scholarly journals Energy Consumption for Uniform Movement of the Upper Parts of Plants between the Upper Conveyor Belt and the Deck

2021 ◽  
pp. 80-84
Author(s):  
В.А. Николаев ◽  
В.В. Гумённый ◽  
В.А. Генералов
Keyword(s):  
Energy Consumption ◽  
Linear Part ◽  
Fluid Pressure ◽  
Conveyor Belt ◽  
Working Fluid ◽  
Grinding Method ◽  
Hydraulic Cylinders ◽  
Maximum Impact Force ◽  
Two Stages ◽  
The Impact

Комбайн, который производил бы выделение зёрен из колосьев методом вытирания, имеет два варианта исполнения устройства для извлечения зёрен из колосьев: с декой, совершающей колебания, и с неподвижной декой. Рассмотрено выделение зёрен из колосьев при неподвижной деке. Перемещение верхних частей растений между лентой верхнего транспортёра и декой включает два этапа. На первом этапе происходит ускорение колосьев, на втором – их равномерное движение. Рассмотрена схема воздействия на колос ленты верхнего транспортёра и деки в начале её равномерного перемещения на прямолинейном участке деки. Определены силы воздействия зерновки на деку и реакции деки. Проанализированы эпюры напряжений, возникающих в колосе от воздействия на колос ленты верхнего транспортёра и деки. Установлено, что напряжения, возникающие в связи зерновок с основанием колоса достаточны для извлечения зерновок из колоса. Выявлено общее максимальное усилие воздействия деки на все колосья, исходя из которого можно произвести расчёт на прочность элементов деки. Вычислено давление рабочей жидкости в гидроцилиндрах поддержки жёлоба, обеспечиваемое гидропневмоаккумулятором. В результате расчётов определены затраты энергии на равномерное перемещение верхних частей растений в промежутке между лентой верхнего транспортёра и декой. The combine, which would extract grains from the ears by grinding method, has two versions of the device for extracting grains from the ears: with a deck making vibrations and with a fixed deck. Grain extraction from ears at fixed deck is considered. The movement of the upper parts of plants between the belt of the upper conveyor and the deck includes two stages. At the first stage the ears accelerate, at the second – their uniform movement takes place. The scheme of influence on the ear of the upper conveyor belt and the deck at the beginning of its uniform movement on the linear part of the deck was considered. The forces of bruchid weevil effect on the deck and reaction of the deck were determined. Stress diagrams arising in the ear from the impact on the ear of the upper conveyor belt and deck were analyzed. It has been found that the stresses arising in connection of the bruchid weevils with the base of the ear are sufficient to extract the bruchid weevils from the ear. The total maximum impact force of the deck on all ears was revealed, based on which it is possible to calculate the strength of the deck elements. Working fluid pressure in gutter support hydraulic cylinders provided by hydro-pneumatic accumulator was calculated. As a result of the calculations, the energy consumption for the uniform movement of the upper parts of plants in the interval between the upper conveyor belt and the deck were determined.

Modeling workflows of energy-saving hydraulic drive of technological equipment of timber-hauling machine

2015 ◽  
Vol 5 (1) ◽  
pp. 223-234
Author(s):  
Посметьев ◽  
Viktor Posmetev ◽  
Канищев ◽  
Denis Kanishchev ◽  
Попиков ◽  
...  
Keyword(s):  
Energy Saving ◽  
Fluid Pressure ◽  
Hydraulic Drive ◽  
Vertical Axis ◽  
Working Fluid ◽  
Forward Movement ◽  
Restoring Force ◽  
Hydraulic Manipulators ◽  
Wide Range ◽  
Hydraulic Cylinders

Workflow mechanisms of forestry cranes tower rotation are accompanied by large dynamic loads that cause sudden changes in fluid pressure in balancing and braking modes. When the rotary column stops at different positions damping of pressure of the working fluid vibration occurs due to its overflow from one chamber to another through an orifice, wherein the hydraulic energy is transformed into heat one, resulting in overheating and energy loss of fluid. Efficient are energy-saving hydropneumatic drives of column of the manipulator which are able to recover energy during transient conditions and to return some of the energy back into the system. For hydraulic manipulators with four paired hydraulic cylinders of rotation mechanism of the column one pair of cylinders is proposed to be replaced by pneumatic cylinders connected to a rotary column through the gear and toothed rack that allows you to transfer it into recovery mode of energy. A mathematical model of the boom rotation of the manipulator is developed; equations for a hydro pneumatic system recovery are made. In the model three mechanical processes are considered: the rotational movement of the column about the vertical axis of the manipulator, the forward movement of the plunger along the axis of the damper, and sway of the load relative to the attachment point on the manipulator arm. To solve the system of differential equations, computer program for the simulation of hydraulic manipulator equipped with a hydraulic damper is composed. The dependence of the restoring force of the displacement of the toothed rack is get. In the vicinity of the equilibrium position, this dependence is nearly linear over a wide range of rack movement: from about 50 to 180 mm. With significant turns of the column volume of one of the chambers of the air cylinder approaches zero value, whereby the restoring force of the module increases significantly, which helps braking of the column in the final step of rotation and influences the process of energy accumulation.

Experimental study of thermohydraulic characteristics and irreversibility analysis of novel axial corrugated tube with spring tape inserts

2020 ◽  
Vol 92 (3) ◽  
pp. 30901
Author(s):  
Suvanjan Bhattacharyya ◽  
Debraj Sarkar ◽  
Ulavathi Shettar Mahabaleshwar ◽  
Manoj K. Soni ◽  
M. Mohanraj
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Thermal Performance ◽  
Working Fluid ◽  
The Novel ◽  
Heat Exchanger Tube ◽  
Heat Transfer Augmentation ◽  
Corrugated Tube ◽  
The Impact ◽  
Exchanger Tube

The current study experimentally investigates the heat transfer augmentation on the novel axial corrugated heat exchanger tube in which the spring tape is introduced. Air (Pr = 0.707) is used as a working fluid. In order to augment the thermohydraulic performance, a corrugated tube with inserts is offered. The experimental study is further extended by varying the important parameters like spring ratio (y = 1.5, 2.0, 2.5) and Reynolds number (Re = 10 000–52 000). The angular pitch between the two neighboring corrugations and the angle of the corrugation is kept constant through the experiments at β = 1200 and α = 600 respectively, while two different corrugations heights (h) are analyzed. While increasing the corrugation height and decreasing the spring ratio, the impact of the swirling effect improves the thermal performance of the system. The maximum thermal performance is obtained when the corrugation height is h = 0.2 and spring ratio y = 1.5. Eventually, correlations for predicting friction factor (f) and Nusselt number (Nu) are developed.

Interference mitigation in point to point wireless sensor networks using LSP protocol and time division multiplexing approach

2020 ◽  
Vol 39 (4) ◽  
pp. 5449-5458
Author(s):  
A. Arokiaraj Jovith ◽  
S.V. Kasmir Raja ◽  
A. Razia Sulthana
Keyword(s):  
Energy Consumption ◽  
Large Scale ◽  
Control Parameter ◽  
Interference Mitigation ◽  
Wireless Sensor ◽  
Point To Point ◽  
A Minor ◽  
Two Stages ◽  
Time Division ◽  
And Control

Interference in Wireless Sensor Network (WSN) predominantly affects the performance of the WSN. Energy consumption in WSN is one of the greatest concerns in the current generation. This work presents an approach for interference measurement and interference mitigation in point to point network. The nodes are distributed in the network and interference is measured by grouping the nodes in the region of a specific diameter. Hence this approach is scalable and isextended to large scale WSN. Interference is measured in two stages. In the first stage, interference is overcome by allocating time slots to the node stations in Time Division Multiple Access (TDMA) fashion. The node area is split into larger regions and smaller regions. The time slots are allocated to smaller regions in TDMA fashion. A TDMA based time slot allocation algorithm is proposed in this paper to enable reuse of timeslots with minimal interference between smaller regions. In the second stage, the network density and control parameter is introduced to reduce interference in a minor level within smaller node regions. The algorithm issimulated and the system is tested with varying control parameter. The node-level interference and the energy dissipation at nodes are captured by varying the node density of the network. The results indicate that the proposed approach measures the interference and mitigates with minimal energy consumption at nodes and with less overhead transmission.

Impact of roof shading on building energy performance in warm & humid climatic places of India

2020 ◽  
pp. 50-64
Author(s):  
Kuladeep Kumar Sadevi ◽  
Avlokita Agrawal
Keyword(s):  
Energy Consumption ◽  
Energy Conservation ◽  
Energy Performance ◽  
General Assumption ◽  
Climatic Conditions ◽  
Building Envelope ◽  
Passive Cooling ◽  
Base Case ◽  
U Value ◽  
The Impact

With the rise in awareness of energy efficient buildings and adoption of mandatory energy conservation codes across the globe, significant change is being observed in the way the buildings are designed. With the launch of Energy Conservation Building Code (ECBC) in India, climate responsive designs and passive cooling techniques are being explored increasingly in building designs. Of all the building envelope components, roof surface has been identified as the most significant with respect to the heat gain due to the incident solar radiation on buildings, especially in tropical climatic conditions. Since ECBC specifies stringent U-Values for roof assembly, use of insulating materials is becoming popular. Along with insulation, the shading of the roof is also observed to be an important strategy for improving thermal performance of the building, especially in Warm and humid climatic conditions. This study intends to assess the impact of roof shading on building’s energy performance in comparison to that of exposed roof with insulation. A typical office building with specific geometry and schedules has been identified as base case model for this study. This building is simulated using energy modelling software ‘Design Builder’ with base case parameters as prescribed in ECBC. Further, the same building has been simulated parametrically adjusting the amount of roof insulation and roof shading simultaneously. The overall energy consumption and the envelope performance of the top floor are extracted for analysis. The results indicate that the roof shading is an effective passive cooling strategy for both naturally ventilated and air conditioned buildings in Warm and humid climates of India. It is also observed that a fully shaded roof outperforms the insulated roof as per ECBC prescription. Provision of shading over roof reduces the annual energy consumption of building in case of both insulated and uninsulated roofs. However, the impact is higher for uninsulated roofs (U-Value of 3.933 W/m2K), being 4.18% as compared to 0.59% for insulated roofs (U-Value of 0.33 W/m2K).While the general assumption is that roof insulation helps in reducing the energy consumption in tropical buildings, it is observed to be the other way when insulation is provided with roof shading. It is due to restricted heat loss during night.

ANALISIS DETERMINAN KUALITAS LINGKUNGAN PERIODE 1999-2013

2016 ◽  
Vol 21 (1) ◽  
pp. 9-20
Author(s):  
Ersalina Tang
Keyword(s):  
Foreign Direct Investment ◽  
Energy Consumption ◽  
Gross Domestic Product ◽  
Co2 Emissions ◽  
Direct Investment ◽  
Meat Consumption ◽  
Domestic Product ◽  
World Data ◽  
The World ◽  
The Impact

The purpose of this study is to analyze the impact of Foreign Direct Investment, Gross Domestic Product, Energy Consumption, Electric Consumption, and Meat Consumption on CO2 emissions of 41 countries in the world using panel data from 1999 to 2013. After analyzing 41 countries in the world data, furthermore 17 countries in Asia was analyzed with the same period. This study utilized quantitative approach with Ordinary Least Square (OLS) regression method. The results of 41 countries in the world data indicates that Foreign Direct Investment, Gross Domestic Product, Energy Consumption, and Meat Consumption significantlyaffect Environmental Qualities which measured by CO2 emissions. Whilst the results of 17 countries in Asia data implies that Foreign Direct Investment, Energy Consumption, and Electric Consumption significantlyaffect Environmental Qualities. However, Gross Domestic Product and Meat Consumption does not affect Environmental Qualities.

The Nexus between Financial Development, Economic Growth and Energy Consumption in India: A VECM Technique

2020 ◽  
pp. 602-612
Keyword(s):  
Economic Growth ◽  
Energy Consumption ◽  
Financial Development ◽  
Consumer Price Index ◽  
Development Economic ◽  
Energy Prices ◽  
Vector Error Correction ◽  
Percent Increase ◽  
Growth Energy ◽  
The Impact

The demand for energy consumption requires efficient financial development in terms of bank credit. Therefore, this study examines the nexus between Financial Development, Economic Growth, Energy Prices and Energy Consumption in India, utilizing Vector Error Correction Model (VECM) technique to determine the nature of short and long term relationships from 2010 to 2019. The estimation of results indicates that a one percent increase in bank credits to private sector results in 0.10 percent increase in energy consumption and 0.28 percent increase in energy consumption responses to 1 percent increase in economic growth. It is also observed that the impact of energy price proxied by consumer price index is statistically significant with a negative sign indicating the consistency with the theory.

scholarly journals Graphene-based 3D XNOR-VRRAM with ternary precision for neuromorphic computing

2021 ◽  
Vol 5 (1) ◽  
Author(s):  
Batyrbek Alimkhanuly ◽  
Joon Sohn ◽  
Ik-Joon Chang ◽  
Seunghyun Lee
Keyword(s):  
Neural Network ◽  
Energy Consumption ◽  
Recognition Accuracy ◽  
Material Selection ◽  
Weighted Sum ◽  
Device Design ◽  
Key Factors ◽  
Neuromorphic Computing ◽  
Device Scaling ◽  
The Impact

AbstractRecent studies on neural network quantization have demonstrated a beneficial compromise between accuracy, computation rate, and architecture size. Implementing a 3D Vertical RRAM (VRRAM) array accompanied by device scaling may further improve such networks’ density and energy consumption. Individual device design, optimized interconnects, and careful material selection are key factors determining the overall computation performance. In this work, the impact of replacing conventional devices with microfabricated, graphene-based VRRAM is investigated for circuit and algorithmic levels. By exploiting a sub-nm thin 2D material, the VRRAM array demonstrates an improved read/write margins and read inaccuracy level for the weighted-sum procedure. Moreover, energy consumption is significantly reduced in array programming operations. Finally, an XNOR logic-inspired architecture designed to integrate 1-bit ternary precision synaptic weights into graphene-based VRRAM is introduced. Simulations on VRRAM with metal and graphene word-planes demonstrate 83.5 and 94.1% recognition accuracy, respectively, denoting the importance of material innovation in neuromorphic computing.

scholarly journals Review on Urban Heat Island in China: Methods, Its Impact on Buildings Energy Demand and Mitigation Strategies

2021 ◽  
Vol 13 (2) ◽  
pp. 762
Author(s):  
Liu Tian ◽  
Yongcai Li ◽  
Jun Lu ◽  
Jue Wang
Keyword(s):  
Energy Consumption ◽  
Urban Heat Island ◽  
Building Energy ◽  
Design Stage ◽  
Heat Island ◽  
Building Energy Consumption ◽  
Rapid Urbanization ◽  
Substantial Impact ◽  
Urban Heat ◽  
The Impact

High population density, dense high-rise buildings, and impervious pavements increase the vulnerability of cities, which aggravate the urban climate environment characterized by the urban heat island (UHI) effect. Cities in China provide unique information on the UHI phenomenon because they have experienced rapid urbanization and dramatic economic development, which have had a great influence on the climate in recent decades. This paper provides a review of recent research on the methods and impacts of UHI on building energy consumption, and the practical techniques that can be used to mitigate the adverse effects of UHI in China. The impact of UHI on building energy consumption depends largely on the local microclimate, the urban area features where the building is located, and the type and characteristics of the building. In the urban areas dominated by air conditioning, UHI could result in an approximately 10–16% increase in cooling energy consumption. Besides, the potential negative effects of UHI can be prevented from China in many ways, such as urban greening, cool material, water bodies, urban ventilation, etc. These strategies could have a substantial impact on the overall urban thermal environment if they can be used in the project design stage of urban planning and implemented on a large scale. Therefore, this study is useful to deepen the understanding of the physical mechanisms of UHI and provide practical approaches to fight the UHI for the urban planners, public health officials, and city decision-makers in China.

scholarly journals Economic Development, CO2 Emissions and Energy Use Nexus-Evidence from the Danube Region Countries

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3165
Author(s):  
Eva Litavcová ◽  
Jana Chovancová
Keyword(s):  
Economic Growth ◽  
Energy Consumption ◽  
Co2 Emissions ◽  
Carbon Emissions ◽  
Bounds Testing ◽  
Mutual Cooperation ◽  
Long Run ◽  
Short Run ◽  
Danube Region ◽  
The Impact

The aim of this study is to examine the empirical cointegration, long-run and short-run dynamics and causal relationships between carbon emissions, energy consumption and economic growth in 14 Danube region countries over the period of 1990–2019. The autoregressive distributed lag (ARDL) bounds testing methodology was applied for each of the examined variables as a dependent variable. Limited by the length of the time series, we excluded two countries from the analysis and obtained valid results for the others for 26 of 36 ARDL models. The ARDL bounds reliably confirmed long-run cointegration between carbon emissions, energy consumption and economic growth in Austria, Czechia, Slovakia, and Slovenia. Economic growth and energy consumption have a significant impact on carbon emissions in the long-run in all of these four countries; in the short-run, the impact of economic growth is significant in Austria. Likewise, when examining cointegration between energy consumption, carbon emissions, and economic growth in the short-run, a significant contribution of CO2 emissions on energy consumptions for seven countries was found as a result of nine valid models. The results contribute to the information base essential for making responsible and informed decisions by policymakers and other stakeholders in individual countries. Moreover, they can serve as a platform for mutual cooperation and cohesion among countries in this region.

Sign in / Sign up

Export Citation Format

Share Document