scholarly journals Design of a Centrifugal Compressor Test Rig

2020 ◽  
Vol 79 (1) ◽  
pp. 63-80
Author(s):  
S. V. Ajaicimhan ◽  
Natteri M Sudharsan
Keyword(s):  
Working Conditions ◽  
Centrifugal Compressor ◽  
Test Facility ◽  
Measuring Instruments ◽  
Test Rig ◽  
Centrifugal Compressors ◽  
Basic Operating ◽  
Complete Test ◽  
The Given ◽  
Good Agreement

Centrifugal compressors find their use in many areas especially in turbochargers which are used extensively in automobiles and in aircrafts and defence systems. This paper presents the design of a complete test facility for testing centrifugal compressors. It starts with design of a Combustor - the driving unit for the test facility. The Centrifugal compressor being tested is a part of a turbocharger. The combustor feeds the Turbine side of the test section with hot gases for running the compressor at desired speeds. This particular choice eliminates the need for the inclusion of heavy speed reducing gears when an electric motor is used as the driving unit. The designed combustor was numerically simulated and subsequently optimized for the given working conditions. The simulated results showed good agreement with the target criteria. Further, the choice and placement of the measuring instruments for the entire test rig and their permissible deviations are listed and finally the basic operating sequence for the entire rig is also drafted for in-house development of automation of the entire test rig thereby making it a complete guide for the setting up of such facility, hitherto establishing a complete guideline of all subsystems which will enable in building such similar facilities in varying magnitudes in the future.

The Effect of Inlet Distortion on the Performance Characteristics of a Centrifugal Compressor

1983 ◽  
Vol 105 (2) ◽  
pp. 223-230 ◽  
Author(s):  
I. Ariga ◽  
N. Kasai ◽  
S. Masuda ◽  
Y. Watanabe ◽  
I. Watanabe
Keyword(s):  
Centrifugal Compressor ◽  
Total Pressure ◽  
Performance Characteristics ◽  
Performance Tests ◽  
Velocity Measurements ◽  
Test Rig ◽  
Low Speed ◽  
Inlet Distortion ◽  
Surge Margin ◽  
The Given

The present paper concerns itself with the effects of total pressure (and thus velocity) distortion on performance characteristics and surge margin of centrifugal compressors. Both radial and circumferential distortions were investigated. The performance tests as well as the velocity measurements within the impeller passages were carried out with a low-speed compressor test rig with the inlet honeycomb as the distortion generators and compared with the case of “no distortion” as a datum. The results indicated that the inlet distortion exerted unfavorable influences on the efficiency and the surge margin of the given compressor, though the influence of the radial distortion was much stronger than that of the circumferential one. Various distortion indices were further examined in order to correlate the performance to the inlet distortion.

scholarly journals The Effect of Inlet Distortion on the Performance Characteristics of a Centrifugal Compressor

1982 ◽  
Author(s):  
I. Ariga ◽  
N. Kasai ◽  
S. Masuda ◽  
Y. Watanabe ◽  
I. Watanabe
Keyword(s):  
Centrifugal Compressor ◽  
Total Pressure ◽  
Performance Characteristics ◽  
Performance Tests ◽  
Velocity Measurements ◽  
Test Rig ◽  
Low Speed ◽  
Inlet Distortion ◽  
Surge Margin ◽  
The Given

The present paper concerns itself with the effects of total pressure (and thus velocity) distortion on performance characteristics and surge margin of centrifugal compressors. Both radial and circumferential distortions were investigated. The performance tests as well as the velocity measurements within the impeller passages were carried out with a low speed compressor test rig with the inlet honeycomb as the distortion generators and compared with the case of “no distortion” as a datum. The results indicated that the inlet distortion exerted unfavorable influences on the efficiency and the surge margin of the given compressor, though the influence of the radial distortion was much stronger than that of the circumferential one. Various distortion indices were further examined in order to correlate the performance to the inlet distortion.

Explosive Decompression Resistance of Centrifugal Compressor O-Ring Seals: A Comparative Test Summary and Procedure

1988 ◽  
Vol 110 (2) ◽  
pp. 289-294 ◽  
Author(s):  
W. N. Shade ◽  
D. W. Legg
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Centrifugal Compressor ◽  
Atmospheric Pressure ◽  
Comparative Test ◽  
Test Results ◽  
Test Rig ◽  
Centrifugal Compressors ◽  
Ring Seal ◽  
Sealing Elements

Explosive decompression is a phenomenon that can destroy O-ring sealing elements in high-pressure (>3.4 MPa) natural gas compressors during rapid venting to atmospheric pressure. A test rig and procedure have been developed to identify important parameters influencing O-ring seal explosive decompression failure, consistent with utilization of these seals in high-pressure centrifugal compressors. The test rig and procedure are described and comparative test results presented.

An Overview of Flow Instabilities Occurring in Centrifugal Compressors Operating At Low Flow Rates

2021 ◽  
Author(s):  
Jiri Vacula ◽  
Pavel Novotny
Keyword(s):  
Centrifugal Compressor ◽  
Flow Instabilities ◽  
Low Flow ◽  
Centrifugal Compressors ◽  
Computational Tools ◽  
Flow Rates ◽  
The World ◽  
The Given

Abstract Researchers from all over the world have been researching the aerodynamics of centrifugal compressors. They have explained many properties of the aerodynamic phenomena occurring in centrifugal compressors during their operation and have introduced various terms. This work presents the crucial knowledge that has been published on the flow instabilities occurring in centrifugal compressors operating at low flow rates. It also introduces the capabilities of the computational tools used for the simulation of these phenomena. The characteristic of the centrifugal compressor including highlighted areas of possible occurrence of typical flow instabilities is presented. This review is extended to include a frequency description of the vibroacoustic behaviour related to these aerodynamic instabilities. The frequency description enables better identification of the given aerodynamic phenomena based on measurements or computations, and relevant sources of literature are provided. The researchers will receive a structured summary of key publications leading to the better understanding of the flow instabilities in centrifugal compressors.

A Discussion of the Factors Affecting Surge in Centrifugal Compressors

1985 ◽  
Vol 107 (2) ◽  
pp. 499-506 ◽  
Author(s):  
R. L. Elder ◽  
M. E. Gill
Keyword(s):  
Mathematical Model ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Factors Affecting ◽  
Pressure Losses ◽  
Complex Mathematical Model ◽  
Good Agreement

The process of surge in a centrifugal compressor has been studied and found to be dependent on a number of complex and often interrelated factors. A major factor defining surge in high-speed, vaned diffuser designs appears to be the flow in the semivaneless space. By developing work initiated by others it has been possible to propose some explanation of previously presented apparently conflicting data. In addition, a more complex mathematical model capable of assessing additional factors is proposed. Using this model good agreement with experimental surge has been obtained. This model takes into consideration pressure losses in the impeller, diffuser, and collector, and by using this model it was possible to identify the stalling elements that are responsible for overall compressor instability.

scholarly journals Quantitative Shape-Classification of Misfitting Precipitates during Cubic to Tetragonal Transformations: Phase-Field Simulations and Experiments

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1373
Author(s):  
Yueh-Yu Lin ◽  
Felix Schleifer ◽  
Markus Holzinger ◽  
Na Ta ◽  
Birgit Skrotzki ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Phase Field ◽  
Phase Field Model ◽  
Invariant Moments ◽  
Plane Normal ◽  
Plane Shape ◽  
Formation And Evolution ◽  
The Given ◽  
Good Agreement

The effectiveness of the mechanism of precipitation strengthening in metallic alloys depends on the shapes of the precipitates. Two different material systems are considered: tetragonal γ′′ precipitates in Ni-based alloys and tetragonal θ′ precipitates in Al-Cu-alloys. The shape formation and evolution of the tetragonally misfitting precipitates was investigated by means of experiments and phase-field simulations. We employed the method of invariant moments for the consistent shape quantification of precipitates obtained from the simulation as well as those obtained from the experiment. Two well-defined shape-quantities are proposed: (i) a generalized measure for the particles aspect ratio and (ii) the normalized λ2, as a measure for shape deviations from an ideal ellipse of the given aspect ratio. Considering the size dependence of the aspect ratio of γ′′ precipitates, we find good agreement between the simulation results and the experiment. Further, the precipitates’ in-plane shape is defined as the central 2D cut through the 3D particle in a plane normal to the tetragonal c-axes of the precipitate. The experimentally observed in-plane shapes of γ′′-precipitates can be quantitatively reproduced by the phase-field model.

scholarly journals Experimental and Numerical Investigation about Small Clearance Journal Bearings under Static Load Conditions

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Carlo Alberto Niccolini Marmont Du Haut Champ ◽  
Fabrizio Stefani ◽  
Paolo Silvestri
Keyword(s):  
Three Dimensional ◽  
Journal Bearings ◽  
Radial Clearance ◽  
Small Scale ◽  
Test Rig ◽  
Small Clearance ◽  
Dimensional Simulation ◽  
Dynamic Loading Conditions ◽  
Static And Dynamic Loading ◽  
Good Agreement

The aim of the present research is to characterize both experimentally and numerically journal bearings with low radial clearances for rotors in small-scale applications (e.g., microgas turbines); their diameter is in the order of ten millimetres, leading to very small dimensional clearances when the typical relative ones (order of 1/1000) are employed; investigating this particular class of journal bearings under static and dynamic loading conditions represents something unexplored. To this goal, a suitable test rig was designed and the performance of its bearings was investigated under steady load. For the sake of comparison, numerical simulations of the lubrication were also performed by means of a simplified model. The original test rig adopted is a commercial rotor kit (RK), but substantial modifications were carried out in order to allow significant measurements. Indeed, the relative radial clearance of RK4 RK bearings is about 2/100, while it is around 1/1000 in industrial bearings. Therefore, the same original RK bearings are employed in this new test rig, but a new shaft was designed to reduce their original clearance. The new custom shaft allows to study bearing behaviour for different clearances, since it is equipped with interchangeable journals. Experimental data obtained by this test rig are then compared with further results of more sophisticated simulations. They were carried out by means of an in-house developed finite element (FEM) code, suitable for thermoelasto-hydrodynamic (TEHD) analysis of journal bearings both in static and dynamic conditions. In this paper, bearing static performances are studied to assess the reliability of the experimental journal location predictions by comparing them with the ones coming from already validated numerical codes. Such comparisons are presented both for large and small clearance bearings of original and modified RKs, respectively. Good agreement is found only for the modified RK equipped with small clearance bearings (relative radial clearance 8/1000), as expected. In comparison with two-dimensional lubrication analysis, three-dimensional simulation improves prediction of journal location and correlation with experimental results.

Roles of vanes in diffuser on stability of centrifugal compressor

2019 ◽  
Vol 233 (14) ◽  
pp. 5380-5392
Author(s):  
Wangzhi Zou ◽  
Xiao He ◽  
Wenchao Zhang ◽  
Zitian Niu ◽  
Xinqian Zheng
Keyword(s):  
High Pressure ◽  
Centrifugal Compressor ◽  
Dynamic Pressure ◽  
Pressure Ratio ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Centrifugal Compressors ◽  
Compression System ◽  
The Stability ◽  
Rotating Instability

The stability considerations of centrifugal compressors become increasingly severe with the high pressure ratios, especially in aero-engines. Diffuser is the major subcomponent of centrifugal compressor, and its performance greatly influences the stability of compressor. This paper experimentally investigates the roles of vanes in diffuser on component instability and compression system instability. High pressure ratio centrifugal compressors with and without vanes in diffuser are tested and analyzed. Rig tests are carried out to obtain the compressor performance map. Dynamic pressure measurements and relevant Fourier analysis are performed to identify complex instability phenomena in the time domain and frequency domain, including rotating instability, stall, and surge. For component instability, vanes in diffuser are capable of suppressing the emergence of rotating stall in the diffuser at full speeds, but barely affect the characteristics of rotating instability in the impeller at low and middle speeds. For compression system instability, it is shown that the use of vanes in diffuser can effectively postpone the occurrence of compression system surge at full speeds. According to the experimental results and the one-dimensional flow theory, vanes in diffuser turn the diffuser pressure rise slope more negative and thus improve the stability of compressor stage, which means lower surge mass flow rate.

Backward Traveling Rotating Stall Waves in Centrifugal Compressors

2002 ◽  
Author(s):  
Z. S. Spakovsky
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
First Principles ◽  
Rotating Stall ◽  
Air Injection ◽  
System Stability ◽  
Centrifugal Compressors ◽  
Injection Scheme ◽  
Surge Margin ◽  
Low Order

Rotating stall waves that travel against the direction of rotor rotation are reported for the first time and a new, low-order analytical approach to model centrifugal compressor stability is introduced. The model is capable of dealing with unsteady radially swirling flows and the dynamic effects of impeller-diffuser component interaction as it occurs in centrifugal compression systems. A simple coupling criterion is developed from first principles to explain the interaction mechanism important for system stability. The model findings together with experimental data explain the mechanism for first-ever observed backward traveling rotating stall in centrifugal compressors with vaned diffusers. Based on the low-order model predictions, an air injection scheme between the impeller and the vaned diffuser is designed for the NASA Glenn CC3 high-speed centrifugal compressor. The steady air injection experiments show an increase of 25% in surge-margin with an injection mass flow of 0.5% of the compressor mass flow. In addition, it is experimentally demonstrated that this injection scheme is robust to impeller tip-clearance effects and that a reduced number of injectors can be applied for similar gains in surge-margin. The results presented in this paper firmly establish the connection between the experimentally observed dynamic phenomena in the NASA CC3 centrifugal compressor and a first principles based coupling criterion. In addition, guidelines are given for the design of centrifugal compressors with enhanced stability.

The influence of the trailing edge angle of the micro centrifugal impeller on the performance of the centrifugal compressor

2021 ◽  
pp. 1-15
Author(s):  
Xu Yu-dong ◽  
Li Cong ◽  
Lv Qiong-ying ◽  
Zhang Xin-ming ◽  
Mu Guo-zhen
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Centrifugal Impeller ◽  
Centrifugal Compressors ◽  
Trailing Edge ◽  
Sweep Angle ◽  
Impeller Blade ◽  
Bending Angle ◽  
Edge Angle ◽  
Isentropic Efficiency

In order to study the effect of the trailing edge sweep angle of the centrifugal impeller on the aerodynamic performance of the centrifugal compressor, 6 groups of centrifugal impellers with different bending angles and 5 groups of different inclination angles were designed to achieve different impeller blade trailing edge angle. The computational fluid dynamics (CFD) method was used to simulate and analyze the flow field of centrifugal compressors with different blade shapes under design conditions. The research results show that for transonic micro centrifugal compressors, changing the blade trailing edge sweep angle can improve the compressor’s isentropic efficiency and pressure ratio. The pressure ratio of the compressor shows a trend of increasing first and then decreasing with the increase of the blade bending angle. When the blade bending angle is 45°, the pressure ratio of the centrifugal compressor reaches a maximum of 1.69, and the isentropic efficiency is 67.3%. But changing the inclination angle of the blade trailing edge has little effect on the isentropic efficiency and pressure ratio. The sweep angle of blade trailing edge is an effective method to improve its isentropic efficiency and pressure ratio. This analysis method provides a reference for the rational selection of the blade trailing edge angle, and provides a reference for the design of micro centrifugal compressors under high Reynolds numbers.

Sign in / Sign up

Export Citation Format

Share Document