Perancangan Mesin Press Tahu Sistem Pnuematik Dengan Kapasitas 50 Kg

This pneumatic system tofu press machine is a press machine that is used to compress tofu starch with a capacity of 50 kg to make tofu that is ready to be marketed. The pneumatic system tofu press machine is made to make it easier to press tofu. Previously, tofu was pressed manually, namely by using a stone as a tofu press which resulted in the length of the tofu compaction process. Pressing with stones can also cause work accidents. This tofu press machine uses pneumatics as a punch driver which will press the tofu. The way this tofu machine works is by pressing the on button on the machine then the punch will move down towards the tofu essence and press the tofu. Punch paused for a moment to make sure the tofu blended in perfectly. Then press the off button on the machine to return the punch to its original position. This pneumatic system tofu press machine can reduce work accidents, lighten work, shorten processing time and is also more hygienic because it uses air as a punch driver.

Pengaruh VariasiArus dan Posisi Pengelasan SMAW terhadap Sifat Mekanik Baja ST 37

The purpose of this study was to determine the difference in the value of tensile strength, impact and microstructure test results on ST 37 steel plates due to variations in current strength of 80 A, 85 A and 90 A and 1G, 2G and 3G welding positions. The results of this study show the value of Max.load, current strength of 80 A 3G welding position gets the highest value of 5650 kgf, value of Tinsile strength, current strength of 80 A 3G welding position gets the highest value of 44.78 (kgf/mm2), then the strain value, the current strength of 80 A for the 3G welding position gets the highest value of 0.9% and the value of the modulus of elasticity, the current strength of 80 A for the 3G welding position gets the highest value of 97.94 (GPa,KN/mm2), In the value of the impact test results, the current strength of 80 A is the 1G welding position that gets the highest value, which is 116 Joules. In the observation of microstructure testing, 3 points were carried out, Weld metal, HAZ and Base metal at each strong current

Combustion Conduct Of A Single-Cylinder Spark-Ignition Affected By Ethanol Fuel Mixtures of Supplement Hydroxy Gas (HHO)

Ethanol is an alternative fuel to replace fossil fuels. Ethanol's high octane value can substitute for power in spark-ignition engines (SI). Gasoline mixed with ethanol will reduce the calorific value generated and intensify the combustion process in the combustion chamber. Through the engine performance test, we can find out the increase in the performance of the SI engine. Several essential variables can improve engine performance, such as gasoline-ethanol variations, iridium spark plugs, and hydroxy gas generators (HHO). This research uses an experimental method by utilizing gasoline (octane-92)-ethanol variations (35%, 45%, and 55% v/v) with the intake of hydroxy gas during the combustion process. The SI automatic transmission engine has a capacity of 124.8 cubic centimeters (one cylinder-four stroke), a compression ratio of 11/1, fuel injection, and iridium spark plugs. Engine performance test using chassis dyno test with engine speed variations of 4000-9000 rpm. This study resulted in optimal performance on a 55% increase in gasoline-ethanol mixture with an intensify in output-power, pressure, and thermal efficiency at an engine-speed of 8000 rpm. It is contrary to the specific fuel consumption has decreased.

Analisis Kebutuhan Debit Air Di Gedung C RSUD Kota Bukittinggi

In the Bukittinggi City Hospital building which has 6 floors, there is a water pump and a reservoir used to supply clean water for daily needs. Based on the reality in the field where there is no secondary data to determine the type of pump and reservoir. The purpose of this analysis is to obtain clean water discharge requirements, obtain the type of pump and ensure that the reservoir used for building C RSUD Kota Bukittinggi is in accordance with the type of pipe and reservoir installed in building C, floor 6. By using field studies and interviews and applying the formulas related to pump calculations. In determining the type of pump to be used in the building, it includes the required water discharge, determining the capacity of the components to be used such as pipe diameter, water tank capacity on the ground floor and roof of the building and the total head on the pipe. Based on the calculation results, the required water discharge is 0.08333 m 3 /min, the upper reservoir has a capacity of 150,000 liters, the bottom reservoir is 5,000 liters and the Hot that occurs is 18.429 m. Then the required pump specifications are 40 x 32B2 -51.5 Grundfos CM 10-3. The pump specifications are not much different from those that have been applied in the field.

Experimental Study on the Effect of Waste Valve Load and the Volume of Air Chamber on the Performance of the Hydraulic Ram Pump (Hydram) to Water the Paddy Field in Pakandangan, Padang Pariaman Regency

This 2019 DIPA Grand’s research designed and fabricated the size of hydraulic ram (hydram) pump utilized in Pakandangan, Padang Pariaman Regency. There is a water source in this area which has not been functioned adequately to irrigate the paddy field of 10 hectares due to the location of the paddy field which is higher than the water source. However, the use of designed hydram pump has no been maximized as the pump’s optimal performance was not determined yet. Therefore, a hydram pump was designed by varying the load of waste valve in the weight of 400 g, 600 g, 800 g, 1,000 g, and 1,200 gr. It was also varied in the volume of the chamber when the pump operated which were 4.86 lt, 5.76 lt, 6.48 lt, 7.29 lt, and 8.1lt. The height (Hd) of the inlet pipe was 1 m, and the lift height (Hs) of the outlet pipe was 5 m. The results obtained from Pump performance increases with increasing cylinder volume. The increase in the load of the exhaust valve volume of the tube remains a significant decrease. Hydram pump performance occurs at a load of 400 g with a tube volume of 8.1 l with an efficiency of 53%

Penerapan Quality Control pada Souvenir Logo PNP dengan Metode Box Plot dan Six Sigma

The quality of a product determines the level of market demand. This paper discusses the determination of the quality level of plastic molding with the sigma level method which uses the Box Plot to determine the desired quality limit. The purpose of this research is to determine the level of quality of product using statistics. The object of this research is to determine the weight variation of the souvenir of PNP logo with a weight indicator. The experiment were carried out on 200 samples taken at random.Then each sample is numbered from 1 to 200. Each sample is weighed carefully. The results obtained were processed using a box plot to obtain the numbered of rejected samples from 200 samples that were weighed. The result of data processing obtained 19 reject products from 200 products tested. From this data there are 9,5% of products that do not meet the desired specifications. Furthermore, the sigma level is determined from the results of data processing using a box plot. DPMO of 9.5% is 95000 Defects per Milion Opportunities. The result of determining the sigma level is 2.8 Sigma.

Perancangan Pembangkit Listrik Pikohydro Dengan Tipe Turbin Screw

The screw type water turbine is one type of water turbine that has the potential to generate electricity on a small scale that is environmentally friendly, where this screw type water turbine is very suitable for rivers and irrigation flows in the territory of Indonesia because the use or operation of this turbine only requires low turbine head, looking at the potential for irrigation river water flow with a discharge range of 0.01-0.1 m3/s located in the lowlands in a Karawang district, it is possible to install or apply this screw type water turbine. In this study aims to be able to utilize the source of irrigation flow so that it can be converted into a source of electrical energy that can be utilized by local residents and for lighting on roads that are still poorly lit. In the process of designing a screw type water turbine, mechanical calculations are carried out to determine thedimensions of the turbine blades, turbine shaft, transmission systems such as pulleys and belts, as well as the power that can be generated by the turbine, with a relative head between 0.5 meters, 0.75 meters, and 0.9 meters and determine the correct components. The results of this calculation are obtained in the form of output power from each different head height for head 0.5, the power obtained is 220.89795 watts, for the 0.75 m head, the power is 394.29519 watts, and for the height 0.9, the output power is 356.13926 watts, the results of the design will then be made and will be realized.

Pembuatan Westafel Otomatis dengan Memanfaatkan Kondensasi AC sebagai Sumber Air

The problem of Coronavirus disease (COVID-19) has not stopped. It was necessary to implement the Covid-19 protocol to avoid spreading, one of which is to wash hand regularly using and circulating water. Based on these reasons, it was still necessary to develop automatic hand washing equipment which is currently a primary need in public places, offices, and educational facilities. This study aims to modify the automatic sink using the Arduino Uno R3 microcontroller as a data processor and Ultrasonic HC-SR04 as a sensor; testing the function of the tool, namely automatic soap and water faucet, hand dryer, piezoelectric buzzer as an air level alarm, by utilizing the results of AC condensation as an water source. The results of this automatic sink modification can meet Covid-19 standards and can be used by all groups, especially schools and offices that have started to be active, so that with this tool it can reduce the spread of Covid-19. In addition, it is that the source of water from the condensation can be used as an alternative to water to save the current increasing use of PDAM water.

Perancangan Mesin Vakum dan Pengemasan Untuk Produksi Olahan Jamur Tiram Dalam Rangka Meningkatkan Nilai Jual dan Masa Pakai

The design of this Vacuum and Packaging Machine is made in order to increase the sale value and service life for processed Oyster Mushroom products. Not only that, this machine can do packaging in a short time and efficiently. This machine consists of Frame, Vacuum Motor, Impulse Sealer, Vacuum Clamp. This Vacuum and Packaging Machine has dimensions of length 700 mm x width 500 mm x height 700 mm. The impulse sealer used is Arashi Ais 400 type by using a VE115N 2 CFM type vacuum motor. From this vacuum motor will later be connected to the vacuum clamp as a tool to clamp the packaging during the process of vacuuming the air in the package. This machine is equipped with a limit switch on the vacuum clamp that works to connect the current to the vacuum motor so that the vacuum motor automatically turns on. The operation of this vacuum and packaging machine is quite simple by inserting the packaging containing the product into the sealer and at the end of the package clamped on the vacuum clamp, the vacuum motor will automatically turn on, the next step is to operate the impulse sealer so that the product is finished packed under vacuum. From the design results, the bending stress of the frame is 3.172 N / mm2, the working time of the vacuum and sealer is 1.54 s per package, and the estimated price of the machine is Rp. 1,879,000

Pengaruh Kecepatan Fluida Pendingin (Udara) Terhadap Unjuk Kerja Dan Karakteristik Perpindahan Panas Pada Radiator Sepeda Motor Yamaha Nmax 155CC

Penelitian ini menggunakan metode ɛ-NTU untuk menganalisis data. Radiator yang digunakan adalah radiator sepeda motor Yamaha Nmax 155cc dengan jenis aliran vertical, flat tube dan louvered fins, kipas/fan sebagai sumber angin simulasi, dengan campuran 50% air + 50% coolant radiator. Laju aliran air konstan 4 lpm dan temperatur fluida panas konstan 80. Variasi kecepatan aliran udara yang digunakan pada pengujian kali ini adalah 4-8 m/s dan diatur menggunakan Dimmer sebagai alat bantu. Dari pengujian yang telah dilakukan didapat laju massa aliran udara yang paling besar terjadi pada kecepatan kipas 8 m/s. Laju perpindahan panas yang paling besar terjadi dikecepatan kipas 8 m/s sebesar 0,0735 kW dan panas menyeluruh terbesar juga terjadi dikecepatan kipas 8 m/s yaitu sebesar 9,50 W/m2°C. Efisiensi radiator maksimum terjadi pada kecepatan kipas 5 m/s dengan nilai sebesar 7,59. Kata kunci: Efektifitas, Metode ε-NTU, Radiator Nmax 155cc. This study uses the ε-NTU method to analyze the data. The radiator used is a 155cc Yamaha Nmax motorcycle radiator with vertical flow type, flat tube and louvered fins, fan/fan as a simulation source, with a mixture of 50% water + 50% coolant radiator. The water flow rate is constant 4 lpm and the hot fluid temperature is constant 80℃. The variation of air flow velocity used in this test is 4-8 m/s and is adjusted using a dimmer as a tool. From the tests that have been carried out, the largest air flow rate occurs at a fan speed of 8 m/s. The highest heat transfer rate occurs at a fan speed of 8 m/s at 0.0735 kW and the largest overall heat also occurs at a fan speed of 8 m/s at 9.50 W/m2°C. The maximum radiator efficiency occurs at a fan speed of 5 m/s with a value of 7.59 Keywords: Effectivenes, ɛ-NTU Method, Nmax 155cc Radiator