scholarly journals Combustion Conduct Of A Single-Cylinder Spark-Ignition Affected By Ethanol Fuel Mixtures of Supplement Hydroxy Gas (HHO)

2021 ◽  
Vol 14 (2) ◽  
pp. 125-129
Author(s):  
Gatot Setyono ◽  
Navik Kholili
Keyword(s):  
Fossil Fuels ◽  
Engine Speed ◽  
Performance Test ◽  
Fuel Injection ◽  
Automatic Transmission ◽  
Combustion Process ◽  
Engine Performance ◽  
Calorific Value ◽  
Spark Ignition ◽  
Fuel Mixtures

Ethanol is an alternative fuel to replace fossil fuels. Ethanol's high octane value can substitute for power in spark-ignition engines (SI). Gasoline mixed with ethanol will reduce the calorific value generated and intensify the combustion process in the combustion chamber. Through the engine performance test, we can find out the increase in the performance of the SI engine. Several essential variables can improve engine performance, such as gasoline-ethanol variations, iridium spark plugs, and hydroxy gas generators (HHO). This research uses an experimental method by utilizing gasoline (octane-92)-ethanol variations (35%, 45%, and 55% v/v) with the intake of hydroxy gas during the combustion process. The SI automatic transmission engine has a capacity of 124.8 cubic centimeters (one cylinder-four stroke), a compression ratio of 11/1, fuel injection, and iridium spark plugs. Engine performance test using chassis dyno test with engine speed variations of 4000-9000 rpm. This study resulted in optimal performance on a 55% increase in gasoline-ethanol mixture with an intensify in output-power, pressure, and thermal efficiency at an engine-speed of 8000 rpm. It is contrary to the specific fuel consumption has decreased.

Study on Fuel and Injection Influence on a Spark Ignition Aeropiston Engine

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Wang Xiaogang ◽  
Liu Bolan ◽  
Yu Xiyang ◽  
Yan Chao ◽  
Yu Fei ◽  
...  
Keyword(s):  
Performance Test ◽  
Fuel Injection ◽  
Combustion Process ◽  
Weight Ratio ◽  
Engine Performance ◽  
Spark Ignition ◽  
Performance Comparison ◽  
Power Performance ◽  
Test Rig ◽  
Injection Methods

Abstract Spark ignition aeropiston engines have good prospects due to light weight and high power to weight ratio. Both gasoline and kerosene can be utilized on these engines by using either traditional port fuel injection (PFI) or the novel air-assisted fuel injection (A2FI). In this article, the effects of different fuels and injection methods on the performance of a four-cylinder opposed aeropiston engine were studied. The spray performance test rig and the engine performance test rig were established. First, the influence of different injection methods on engine performance were compared, which indicated that A2FI is superior to PFI in engine power and starting performance. Furthermore, the fuel performance comparison by using A2FI was conducted, which demonstrates that kerosene is inferior to gasoline in terms of spray characteristics and power performance. Finally, detailed working characteristics of A2FI system using kerosene were studied, which indicated that the stable and reliable operation of the spark-ignition operation can be realized and the kerosene's spark-ignition combustion process can be optimized similar to that of gasoline. Results shows that the use of kerosene combined with A2FI is the best technical way to achieve ideal working process of the spark ignition aeropiston engine.

An Experimental and Numerical Investigation of Spark Ignition Engine Operation on H2, CO, CH4, and Their Mixtures

2009 ◽  
Vol 132 (3) ◽  
Author(s):  
Hailin Li ◽  
Ghazi A. Karim ◽  
A. Sohrabi
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Combustion Characteristics ◽  
Spark Ignition Engine ◽  
Engine Operation ◽  
Dry Air ◽  
Fuel Mixtures ◽  
Co Addition ◽  
H2 Addition

The knock and combustion characteristics of CO, H2, CH4, and their mixtures were determined experimentally in a variable compression ratio spark ignition (SI) cooperative fuel research (CFR) engine. The significant effects of gaseous fuel mixtures containing H2 in enhancing the combustion and oxidation process of CH4 were examined. The unique combustion characteristics of CO in dry air and its distinct performance in mixtures with H-containing fuels were investigated. The addition of a simulated synthesis gas (2H2+CO) to CH4 was found to enhance the combustion process of the resulting mixture and lowers its knock resistance. The effectiveness of such an addition is slightly weaker than that of a comparable H2 addition but much stronger than that with CO addition only. A predictive model with detailed kinetic chemistry was used successfully to simulate SI engine operation fuelled with CH4, H2, CO, and their mixtures. The predicted engine performance and knock limits of CH4, H2, CO, and their mixtures agree well with experimental data with the exception around pure CO operation in dry air with the presence of small amounts of CH4 or H2. A remedial approach to improve the prediction of the knock limits of fuel mixtures containing mainly CO with a small amount of H-containing fuels such as H2 and CH4 was proposed and discussed.

scholarly journals Impact of Pyrolysis Oil Addition to Ethanol on Combustion in the Internal Combustion Spark Ignition Engine

2021 ◽  
Vol 3 (2) ◽  
pp. 450-461
Author(s):  
Magdalena Szwaja ◽  
Mariusz Chwist ◽  
Stanislaw Szwaja ◽  
Romualdas Juknelevičius
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Calorific Value ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
Pyrolysis Oil ◽  
Indicated Mean Effective Pressure ◽  
Spark Timing

Thermal processing (torrefaction, pyrolysis, and gasification), as a technology can provide environmentally friendly use of plastic waste. However, it faces a problem with respect to its by-products. Pyrolysis oil obtained using this technology is seen as a substance that is extremely harmful for living creatures and that needs to be neutralized. Due to its relatively high calorific value, it can be considered as a potential fuel for internal combustion spark-ignition engines. In order make the combustion process effective, pyrolysis oil is blended with ethanol, which is commonly used as a fuel for flexible fuel cars. This article presents results from combustion tests conducted on a single-cylinder research engine at full load working at 600 rpm at a compression ratio of 9.5:1, and an equivalence ratio of 1. The analysis showed improvements in combustion and engine performance. It was found that, due to the higher calorific value of the blend, the engine possessed a higher indicated mean effective pressure. It was also found that optimal spark timing for this ethanol-pyrolysis oil blend was improved at a crank angle of 2–3° at 600 rpm. In summary, ethanol-pyrolysis oil blends at a volumetric ratio of 3:1 (25% pyrolysis oil) can successfully substitute ethanol in spark-ignition engines, particularly for vehicles with flexible fuel type.

Diesel engine performance mapping using a parametrized mixing time model

2017 ◽  
Vol 19 (2) ◽  
pp. 202-213 ◽  
Author(s):  
Michal Pasternak ◽  
Fabian Mauss ◽  
Christian Klauer ◽  
Andrea Matrisciano
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Mixing Time ◽  
Combustion Process ◽  
Engine Performance ◽  
Injection Timing ◽  
Engine Control ◽  
Reactor Model ◽  
Time Model ◽  
Tabulated Chemistry

A numerical platform is presented for diesel engine performance mapping. The platform employs a zero-dimensional stochastic reactor model for the simulation of engine in-cylinder processes. n-Heptane is used as diesel surrogate for the modeling of fuel oxidation and emission formation. The overall simulation process is carried out in an automated manner using a genetic algorithm. The probability density function formulation of the stochastic reactor model enables an insight into the locality of turbulence–chemistry interactions that characterize the combustion process in diesel engines. The interactions are accounted for by the modeling of representative mixing time. The mixing time is parametrized with known engine operating parameters such as load, speed and fuel injection strategy. The detailed chemistry consideration and mixing time parametrization enable the extrapolation of engine performance parameters beyond the operating points used for model training. The results show that the model responds correctly to the changes of engine control parameters such as fuel injection timing and exhaust gas recirculation rate. It is demonstrated that the method developed can be applied to the prediction of engine load–speed maps for exhaust NOx, indicated mean effective pressure and fuel consumption. The maps can be derived from the limited experimental data available for model calibration. Significant speedup of the simulations process can be achieved using tabulated chemistry. Overall, the method presented can be considered as a bridge between the experimental works and the development of mean value engine models for engine control applications.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

scholarly journals Impact of Simulated Biogas Compositions (CH4 and CO2) on Vibration, Sound Pressure and Performance of a Spark Ignition Engine

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 7037
Author(s):  
Donatas Kriaučiūnas ◽  
Tadas Žvirblis ◽  
Kristina Kilikevičienė ◽  
Artūras Kilikevičius ◽  
Jonas Matijošius ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Negative Correlation ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Sound Pressure ◽  
Raw Materials ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Positive Correlation

Biogas has increasingly been used as an alternative to fossil fuels in the world due to a number of factors, including the availability of raw materials, extensive resources, relatively cheap production and sufficient energy efficiency in internal combustion engines. Tightening environmental and renewable energy requirements create excellent prospects for biogas (BG) as a fuel. A study was conducted on a 1.6-L spark ignition (SI) engine (HR16DE), testing simulated biogas with different methane and carbon dioxide contents (100CH4, 80CH4_20CO2, 60CH4_40CO2, and 50CH4_50CO2) as fuel. The rate of heat release (ROHR) was calculated for each fuel. Vibration acceleration time, sound pressure and spectrum characteristics were also analyzed. The results of the study revealed which vibration of the engine correlates with combustion intensity, which is directly related to the main measure of engine energy efficiency—break thermal efficiency (BTE). Increasing vibrations have a negative correlation with carbon monoxide (CO) and hydrocarbon (HC) emissions, but a positive correlation with nitrogen oxide (NOx) emissions. Sound pressure also relates to the combustion process, but, in contrast to vibration, had a negative correlation with BTE and NOx, and a positive correlation with emissions of incomplete combustion products (CO, HC).

scholarly journals Performance and Emissions of a Spark Ignition Engine Operated with Gasoline Supplemented with Pyrogasoline and Ethanol

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4671
Author(s):  
Luís Durão ◽  
Joaquim Costa ◽  
Tiago Arantes ◽  
F. P. Brito ◽  
Jorge Martins ◽  
...  
Keyword(s):  
Fossil Fuels ◽  
Agricultural Land ◽  
Synergistic Effects ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Ternary Mixtures ◽  
Partial Replacement ◽  
Chemical Compositions ◽  
Waste Biomass

The partial replacement of fossil fuels by biofuels contributes to a reduction of CO2 emissions, alleviating the greenhouse effect and climate changes. Furthermore, fuels produced from waste biomass materials have no impact on agricultural land use and reduce deposition of such wastes in landfills. In this paper we evaluate the addition of pyrolysis biogasoline (pyrogasoline) as an additive for fossil gasoline. Pyrogasoline was produced from used cooking oils unfit to produce biodiesel. This study was based on a set of engine tests using binary and ternary mixtures of gasoline with 0, 2.5, and 5% pyrogasoline and ethanol. The use of ternary blends of gasoline and two different biofuels was tested with the purpose of achieving optimal combustion conditions and lower emissions, taking advantage of synergistic effects due to the different properties and chemical compositions of those biofuels. The tests were performed on a spark-ignition engine, operated at full load (100% throttle, or WOT—wide open throttle) between 2000 and 6000 rpm, while recording engine performance and exhaust gases pollutants data. Binary mixtures with pyrogasoline did not improve or worsen the engine’s performance, but the ternary mixtures (gasoline + pyrogasoline + ethanol) positively improved the engine’s performance with torque gains between 0.8 and 3.1% compared to gasoline. All fuels presented CO and unburned hydrocarbons emissions below those produced by this type of engine operated under normal (fossil) gasoline. On the other hand, NOx emissions from oxygenated fuels had contradictory behaviour compared to gasoline. If we consider the gains achieved by the torque with the ternary mixtures and reductions in polluting emissions obtained by mixtures with pyrogasoline, a future for this fuel can be foreseen as a partial replacement of fossil gasoline.

scholarly journals Simulation of spark ignition engine performance working on biogas hydrogen mixture

2018 ◽  
Vol 244 ◽  
pp. 03001
Author(s):  
Donatas Kriaučiūnas ◽  
Saugirdas Pukalskas ◽  
Alfredas Rimkus
Keyword(s):  
Carbon Dioxide ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Simulation Results ◽  
Crankshaft Rotation ◽  
Carbon Dioxide Co2 ◽  
Engine Crankshaft ◽  
Lower Heating

Numerical simulations of Nissan Qashqai HR16DE engine with increased compression ratio from 10,7:1 to 13,5:1 was carried out using AVL BOOST software. Modelled engine work cycles while engine works with biogas (BG) and hydrogen (H2) mixtures. For biogas used mixture of 35 % carbon dioxide (CO2) and 65 % methane (CH4). Three mixtures of biogas with added 5 %, 10 % and 15 % H2 was made. The simulation of engine work cycles was performed at fully opened throttle and changing engine crankshaft rotation speeds: ne1 = 1500, ne2 = 3000, ne3 = 4500, ne4 = 6000 rpm. Simulation results demonstrated what adding hydrogen to biogas increase in-cylinder temperature and nitrogen oxides (NOx) concentration because of higher mixtures lower heating values (LHV) and better combustion process. Other emissions of carbon monoxide (CO) and hydrocarbons (HC) decreased while adding hydrogen due to the fact that hydrogen is carbon-free fuel.

scholarly journals Experimental Methodology and Facility for the J69-Engine Performance and Emissions Evaluation Using Jet A1 and Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4530 ◽  
Author(s):  
Gabriel Talero ◽  
Camilo Bayona-Roa ◽  
Giovanny Muñoz ◽  
Miguel Galindo ◽  
Vladimir Silva ◽  
...  
Keyword(s):  
Fossil Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Experimental Tests ◽  
Experimental Methodology ◽  
Injection System ◽  
Small Scale ◽  
Gas Temperature ◽  
Maximum Increase

Aeronautic transport is a leading energy consumer that strongly contributes to greenhouse gas emissions due to a significant dependency on fossil fuels. Biodiesel, a substitution of conventional fuels, is considered as an alternative fuel for aircrafts and power generation turbine engines. Unfortunately, experimentation has been mostly limited to small scale turbines, and technical challenges remain open regarding operational safety. The current study presents the facility, the instrumentation, and the measured results of experimental tests in a 640 kW full-scale J69-T-25A turbojet engine, operating with blends of Jet A1 and oil palm biodiesel with volume contents from 0% to 10% at different load regimes. Findings are related to the fuel injection system, the engine thrust, and the emissions. The thrust force and the exhaust gas temperature do not expose a significant variation in all the operation regimes with the utilization of up to 10% volume content of biodiesel. A maximum increase of 36% in fuel consumption and 11% in injection pressure are observed at idle operation between B0 and B10. A reduction of the CO and HC emissions is also registered with a maximum variation at the cruise regime (80% Revolutions Per Minute—RPM).

A comparative study of the effect of compression ratio on the efficiency and flame development angle in a Cooperative Fuel Research engine fueled with binary gasoline–alcohol blends

2019 ◽  
pp. 146808741985910 ◽  
Author(s):  
Guillermo Rubio-Gómez ◽  
Lis Corral-Gómez ◽  
David Rodriguez-Rosa ◽  
Fausto A Sánchez-Cruz ◽  
Simón Martínez-Martínez
Keyword(s):  
Comparative Study ◽  
Compression Ratio ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Flame Development ◽  
The Impact

In the last few years, increasing concern about the harmful effects of the use of fossil fuels in internal combustion engines has been observed. In addition, the limited availability of crude oil has driven the interest in alternative fuels, especially biofuels. In the context of spark ignition engines, bioalcohols are of great interest owing to their similarities and blend capacities with gasoline. Methanol and ethanol have been widely used, mainly due to their knocking resistance. Another alcohol of great interest is butanol, thanks to its potential of being produced as biofuel and its heat value closer to gasoline. In this study, a comparative study of gasoline–alcohol blend combustion, with up to 20% volume, with neat gasoline has been carried out. A single-cylinder, variable compression ratio, Cooperative Fuel Research-type spark ignition engine has been employed. The comparison is made in terms of fuel conversion efficiency and flame development angle. Relevant information related to the impact in the combustion process of the use of the three main alcohols used in blends with gasoline has been obtained.

Sign in / Sign up

Export Citation Format

Share Document