Experimental Studies of a Ranque-Hilsch Vortex Tube

2013 ◽  
Vol 390 ◽  
pp. 670-674 ◽  
Author(s):  
Azizul Mohamad ◽  
Nasrul Amri Mohd Amin ◽  
Zuradzman Mohamad Razlan ◽  
Mohd Shukry Abdul Majid
Keyword(s):  
Vortex Tube ◽  
Experimental Studies ◽  
The Other ◽  
Maximum Temperature ◽  
Physical Parameters ◽  
Inlet Temperature ◽  
Heating Effect ◽  
Design Features ◽  
Air Mass ◽  
Very High

Vortex tube is a device that separates a compressed flow of gas into two streams simultaneously, one giving kinetic energy to the other, resulting one hotter than the inlet temperature and one lower, without having any moving part. This research focuses on investigating the effects of various physical parameters on the performance of the vortex tube, namely cold nozzle diameter, length of the tube, and air mass flow rate at the hot end of the tube. In general, there are two major design features associated with the vortex tube, namely (a) maximum temperature differentials in vortex tube to produce small amount of air with very low and very high temperatures, and (b) maximum cooling/heating effect by producing large quantity of air with moderate temperatures. By considering the experimental results, an optimized set of parameters that contribute to the most efficient vortex tube design would be proposed depending on the desired design features.

Performance Characteristics of a Microscale Ranque–Hilsch Vortex Tube

2008 ◽  
Vol 130 (10) ◽  
Author(s):  
A. F. Hamoudi ◽  
A. Fartaj ◽  
G. W. Rankin
Keyword(s):  
Reynolds Number ◽  
Vortex Tube ◽  
Reynolds Numbers ◽  
Performance Characteristics ◽  
Energy Separation ◽  
Dimensionless Temperature ◽  
Inlet Temperature ◽  
Separation Performance ◽  
Air Mass ◽  
Cold Air

The results of an experimental investigation of the energy separation performance of a microscale Ranque–Hilsch vortex tube are presented. The supply channel Reynolds number of a microscale Ranque–Hilsch vortex tube is varied over a considerable range, which extends into the laminar flow regime in order to determine the minimum conditions for cooling. Experiments are conducted for a fixed geometry and control valve setting. At low Reynolds numbers based on the inlet tube hydraulic diameter and average velocity, the results exhibit an increase in dimensionless temperature in both the hot and cold outlets as the Reynolds number is increased from zero, reaching maximum values below 500 and 1000, respectively. The hot outlet dimensionless temperature decreases after reaching its maximum and achieves a minimum value at a Reynolds number below 1500. It then increases steadily with further increases in Reynolds number. The cold outlet dimensionless temperature decreases steadily after the maximum to become negative at a Reynolds number of approximately 1800. This implies that the cooling effect occurs at Reynolds numbers consistent with turbulent flow. The performance characteristics of the microscale vortex tube operating at higher inlet pressures of 200kPa, 300kPa, and 400kPa with an average inlet temperature of 293.6K are also presented for cold air mass ratio values over the range of 0.05–0.95. An increase in the inlet pressure causes the values of the dimensionless cold temperature difference to increase over the whole range of the cold air mass fraction. An unstable operation is observed at a length to diameter ratio of approximately 10, causing radial mixing between the cold and hot flow streams and a dramatic change in the cold mass flow fraction plot.

Effects of Attachment Styles on the Experience of Equity in Heterosexual Couples Relationships

2003 ◽  
Vol 50 (4) ◽  
pp. 298-310 ◽  
Author(s):  
Ina Grau ◽  
Jörg Doll
Keyword(s):  
Attachment Theory ◽  
Attachment Style ◽  
Intimate Relationships ◽  
Attachment Styles ◽  
Experimental Studies ◽  
The Other ◽  
Heterosexual Couples ◽  
Secure Attachment ◽  
Dependent Variables ◽  
Equity Ratio

Abstract. Employing one correlational and two experimental studies, this paper examines the influence of attachment styles (secure, anxious, avoidant) on a person’s experience of equity in intimate relationships. While one experimental study employed a priming technique to stimulate the different attachment styles, the other involved vignettes describing fictitious characters with typical attachment styles. As the specific hypotheses about the single equity components have been developed on the basis of the attachment theory, the equity ratio itself and the four equity components (own outcome, own input, partner’s outcome, partner’s input) are analyzed as dependent variables. While partners with a secure attachment style tend to describe their relationship as equitable (i.e., they give and take extensively), partners who feel anxious about their relationship generally see themselves as being in an inequitable, disadvantaged position (i.e., they receive little from their partner). The hypothesis that avoidant partners would feel advantaged as they were less committed was only supported by the correlational study. Against expectations, the results of both experiments indicate that avoidant partners generally see themselves (or see avoidant vignettes) as being treated equitably, but that there is less emotional exchange than is the case with secure partners. Avoidant partners give and take less than secure ones.

Thrombotic Thrombocytopenic Purpura: Mechanism for Effectiveness of Plasmapheresis

1979 ◽  
Author(s):  
J. G. Kelton ◽  
P. B. Neame ◽  
I. Walker ◽  
A. G. Turpie ◽  
J. McBride ◽  
...  
Keyword(s):  
Platelet Count ◽  
Thrombotic Thrombocytopenic Purpura ◽  
The Other ◽  
Unknown Etiology ◽  
Normal Range ◽  
Antiplatelet Antibody ◽  
Thrombocytopenic Purpura ◽  
Serious Illness ◽  
Normal Platelet ◽  
Very High

Thrombotic thrombocytopenic purpura (TTP) is a rare but serious illness of unknown etiology. Treatment by plasmapheresis has been reported to be effective but the mechanism for benefit is unknown. We have investigated the effect of plasmapheresis in 2 patients with TTP by quantitating platelet associated IgG (PAIgG) levels prior to and following plasmapheresis. Both patients had very high levels of PAIgG at presentation (90 and A8 fg IgG/platelet respectively, normal 0-5). in both, the PAIgG levels progressively fell to within the normal range and the platelet count rose following plasmapheresis. One patient remained in remission with normal platelet counts and PAIgG levels. The other relapsed after plasmapheresis and the PAIgG level rose prior to the fall in platelet count. Plasmapheresis was repeated and resulted in normalization of both the platelet count and PAIgG level. It is suggested that plasmapheresis removes antiplatelet antibody or immune complexes which may be of etiological importance in this illness.

Computational and experimental studies of the strength of full-scale samples of pipes with defects "metal loss" and "dent with groove"

2020 ◽  
Vol 10 (3) ◽  
pp. 226-233
Author(s):  
Dmitry A. Neganov ◽  
◽  
Victor M. Varshitsky ◽  
Andrey A. Belkin ◽  
◽  
...  
Keyword(s):  
Internal Pressure ◽  
Experimental Studies ◽  
Full Scale ◽  
The Other ◽  
Metal Loss ◽  
Calculation Methods ◽  
Reliable Operation ◽  
Sufficient Stability ◽  
Comparative Results ◽  
The Moment

The article contains the comparative results of the experimental and calculated research of the strength of a pipeline with such defects as “metal loss” and “dent with groove”. Two coils with diameter of 820 mm and the thickness of 9 mm of 19G steel were used for full-scale pipe sample production. One of the coils was intentionally damaged by machining, which resulted in “metal loss” defect, the other one was dented (by press machine) and got groove mark (by chisel). The testing of pipe samples was performed by applying static internal pressure to the moment of collapse. The calculation of deterioration pressure was carried out with the use of national and foreign methodical approaches. The calculated values of collapsing pressure for the pipe with loss of metal mainly coincided with the calculation experiment results based on Russian method and ASME B31G. In case of pipe with dent and groove the calculated value of collapsing pressure demonstrated greater coincidence with Russian method and to a lesser extent with API 579/ASME FFS-1. In whole, all calculation methods demonstrate sufficient stability of results, which provides reliable operation of pipelines with defects.

COMPUTATIONAL AND EXPERIMENTAL STUDIES OF A LOW-EMISSION BURNER FOR A PERSPECTIVE TURBOJET ENGINE WITH THE COMPRESSION RATIO EXCEEDING 40

2020 ◽  
Author(s):  
M. A. Danilov ◽  
◽  
M. V. Drobysh ◽  
A. N. Dubovitsky ◽  
F. G. Markov ◽  
...  
Keyword(s):  
Compression Ratio ◽  
Experimental Studies ◽  
The Other ◽  
Aircraft Engines ◽  
Engine Efficiency ◽  
Other Hand ◽  
Turbojet Engine ◽  
Low Emission ◽  
Civil Aircraft ◽  
The One

Restrictions of emissions for civil aircraft engines, on the one hand, and the need in increasing the engine efficiency, on the other hand, cause difficulties during development of low-emission combustors for such engines.

Growth Characteristics of Activated Sludges Acclimated to para-Nitrophenol in Batch and Continuous Modes

1994 ◽  
Vol 29 (7) ◽  
pp. 327-333
Author(s):  
Y. Matsui ◽  
F. Yamaguchi ◽  
Y. Suwa ◽  
Y. Urushigawa
Keyword(s):  
Growth Characteristics ◽  
The Other ◽  
Operational Mode ◽  
Continuous Mode ◽  
Relative Resistance ◽  
Batch Mode ◽  
The Given ◽  
Operational Modes ◽  
Very High ◽  
Sensitive Group

Activated sludges were acclimated to p-nitrophenol (PNP) in two operational modes, a batch and a continuous. The operational mode of the PNP acclimation of activated sludges strongly affected the physiological characteristics of predominant microorganisms responsible for PNP degradation. Predominant PNP degraders in the sludge in batch mode (Sludge B) had lower PNP affinity and were relatively insensitive to PNP concentration. Those of the sludge in continuous mode (Sludge C), on the other hand, had very high PNP affinity and were sensitive to PNP. MPN enumeration of PNP degraders in sludge B and C using media with different PNP concentrations (0.05, 0.2,0.5 and 2.0 mM) supported the above results. Medium with 0.2 mM of PNP did not recover PNP degraders in sludge C well, while it recovered PNP degraders in sludge B as well as the medium with 0.05 mM did. When switching from one operational mode to the other, the predominant population in sludge B shifted to the sensitive group, but that of sludge C did not shift at the given loading of PNP, showing relative resistance to inhibitive concentration.

Islamic hedging for pilgrimage funds: case of Indonesia

2019 ◽  
Vol 11 (3) ◽  
pp. 328-341
Author(s):  
Rifki Ismal ◽  
Nurul Izzati Septiana
Keyword(s):  
Exchange Rate ◽  
The Other ◽  
Exchange Rate Risk ◽  
Content Type ◽  
Other Hand ◽  
Rate Risk ◽  
Risk Identify ◽  
Hajj Season ◽  
The Right ◽  
Very High

Purpose The demand for Saudi Arabian real (SAR) is very high in the pilgrimage (hajj) season while the authority, unfortunately, does not hedge the hajj funds. As such, the hajj funds are potentially exposed to exchange rate risk, which can impact the value of hajj funds and generate extra cost to the pilgrims. The purpose of this paper is to conduct simulations of Islamic hedging for pilgrimage funds to: mitigate and minimize exchange rate risk, identify and recommend the ideal time, amount and tenors of Islamic hedging for hajj funds, estimate cost saving by pursuing Islamic hedging and propose technical and general recommendations for the authority. Design/methodology/approach Forward transaction mechanism is adopted to compute Islamic forward between SAR and Rupiah (Indonesian currency) or IDR. Findings – based on simulations, the paper finds that: the longer the Islamic hedging tenors, the better is the result of Islamic hedging, the decreasing of IDR/USD is the right time to hedge the hajj funds and, on the other hand, the IDR/SAR appreciation is not the right time to hedge the hajj funds. Findings Based on simulations, the paper finds that: the longer the Islamic hedging tenors, the better is the result of Islamic hedging, the decreasing of IDR/USD is the right time to hedge the hajj funds and, on the other hand, the IDR/SAR appreciation is not the right time to hedge the hajj funds. Research limitations/implications The research suggests the authority to (and not to) hedge the hajj fund, depending on economic conditions and market indicators. Even though the assessment is for the Indonesian case, other countries maintaining hajj funds might also learn from this paper. Originality/value To the best of author’s knowledge, this is the first paper in Indonesia that attempts to simulate the optimal hedging of hajj funds.

scholarly journals Numerical Investigation of the Effect of Air Leaking into the Working Fluid on the Performance of a Steam Ejector

2021 ◽  
Vol 11 (13) ◽  
pp. 6111
Author(s):  
He Li ◽  
Xiaodong Wang ◽  
Jiuxin Ning ◽  
Pengfei Zhang ◽  
Hailong Huang
Keyword(s):  
Flow Structure ◽  
Mass Fraction ◽  
Internal Flow ◽  
Working Fluid ◽  
Physical Parameters ◽  
Entrainment Ratio ◽  
Air Mass ◽  
Steam Ejector ◽  
Primary Fluid ◽  
Mass Fractions

This paper investigated the effect of air leaking into the working fluid on the performance of a steam ejector. A simulation of the mixing of air into the primary and secondary fluids was performed using CFD. The effects of air with a 0, 0.1, 0.3 and 0.5 mass fraction on the entrainment ratio and internal flow structure of the steam ejector were studied, and the coefficient distortion rates for the entrainment ratios under these air mass fractions were calculated. The results demonstrated that the air modified the physical parameters of the working fluid, which is the main reason for changes in the entrainment ratio and internal flow structure. The calculation of the coefficient distortion rate of the entrainment ratio illustrated that the air in the primary fluid has a more significant impact on the change in the entrainment ratio than that in the secondary fluid under the same air mass fraction. Therefore, the air mass fraction in the working fluid must be minimized to acquire a precise entrainment ratio. Furthermore, this paper provided a method of inspecting air leakage in the experimental steam ejector refrigeration system.

scholarly journals Effort investment in uncontrollable situations: The moderating role of motivation toward closure

2021 ◽  
Vol 45 (2) ◽  
pp. 186-196
Author(s):  
Paulina Szwed ◽  
Małgorzata Kossowska ◽  
Marcin Bukowski
Keyword(s):  
Blood Pressure ◽  
Experimental Studies ◽  
The Other ◽  
Need For Closure ◽  
Extra Effort ◽  
Moderating Role ◽  
Energy Conservation Principle ◽  
Principle Of Energy Conservation ◽  
Investment Behaviour

AbstractAccording to the principle of energy-conservation principle, effort investment is usually reduced in situations that are perceived as uncontrollable. This is because when success is recognized as impossible, any effortful actions are no longer justified. However, we predicted that individual differences in uncertainty tolerance, i.e., the need for closure (NFC), may moderate effort investment in uncontrollable situations. We tested this prediction in two experimental studies in which we exposed participants with differing levels of NFC to uncontrollable events, and indexed effort through the assessment of systolic blood pressure (SBP) responses. As predicted, in the uncontrollability (vs. controllability) condition, effort investment decreased significantly among low- but not high-NFC participants. Since gaining certainty and achieving closure is not a critical epistemic goal for low-NFC individuals, exerting extra effort to gain certainty is therefore no longer justified. On the other hand, high-NFC participants do not withhold their efforts, as they are highly motivated to obtain certainty. These results may help to account for contradictory findings in effort-investment behaviour and add substantively to the literature concerning motivation toward closure.

Rolling and Recrystallization Textures in High Purity Al Cold Rolled to Very High Rolling Reductions

2005 ◽  
Vol 495-497 ◽  
pp. 603-608 ◽  
Author(s):  
Atsushi Todayama ◽  
Hirosuke Inagaki
Keyword(s):  
Cold Rolling ◽  
High Purity ◽  
Work Hardening ◽  
Dynamic Recovery ◽  
The Other ◽  
Rolling Reduction ◽  
Theoretical Investigations ◽  
Theoretical Predictions ◽  
Cold Rolled ◽  
Very High

On the basis of Taylor-Bishop-Hill’s theory, many previous theoretical investigations have predicted that, at high rolling reductions, most of orientations should rotate along theβfiber from {110}<112> to {123}<634> and finally into the {112}<111> stable end orientations. Although some exceptions exist, experimental observations have shown, on the other hand, that the maximum on the β fiber is located still at about {123}<634> even after 97 % cold rolling. In the present paper, high purity Al containing 50 ppm Cu was cold rolled up to 99.4 % reduction in thickness and examined whether {112}<111> stable end orientation could be achieved experimentally. It was found that, with increasing rolling reduction above 98 %, {110}<112> decreased, while orientations in the range between {123}<634> and {112}<111> increased, suggesting that crystal rotation along the βfiber from {110}<112> toward {123}<634> and {112}<111> in fact took place. At higher rolling reductions, however, further rotation of this peak toward {112}<111> was extremely sluggish, and even at the highest rolling reduction, it could not arrive at {112}<111>. Such discrepancies between theoretical predictions and experimental observations should be ascribed to the development of dislocation substructures, which were formed by concurrent work hardening and dynamic recovery. Since such development of dislocation substructures are not taken into account in Taylor-Bishop-Hill’s theory, it seems that they can not correctly predict the development of rolling textures at very high rolling reductions, i. e. stable end orientations. On annealing specimens rolled above 98 % reduction in thickness, cube textures were very weak, suggesting that cube bands were almost completely rotated into other orientations during cold rolling. {325}<496>, which lay at an intermediate position between {123}<634> and {112}<111> along theβfiber, developed strongly in the recrystallization textures.

Sign in / Sign up

Export Citation Format

Share Document