Measurement System for Oil-Water-Air Interface Position and Oil Layer Thickness

2014 ◽  
Vol 701-702 ◽  
pp. 518-521
Author(s):  
Yue Feng Li ◽  
Jie Sun ◽  
Hao Ren
Keyword(s):  
Layer Thickness ◽  
Measurement System ◽  
Optical Amplification ◽  
Interface Position ◽  
Air Interface ◽  
Amplification System ◽  
Oil Water ◽  
The Difference ◽  
Physical And Chemical ◽  
Air Interfaces

The measurement system adopts linear CCD as photographic element. Through the optical amplification system, the images of oil-water and oil-air interfaces were clearly imaged onto CCD chip. CCD transforms optical signals into electronically signals, and then submits data to PC through USB channel. After Savitzky-Golay smoothing on light intensity data, the software analyzes the data and calculate out the positions of oil-water-air interfaces. By calculating the difference between two positions, the oil layer thickness is gotten. The experiment results that the measurement system given in this paper is reasonable, stable, effective and accurate. This measurement system has wide application in the physical and chemical industry field.

scholarly journals Investigations on the Optical Properties of InGaN/GaN Multiple Quantum Wells with Varying GaN Cap Layer Thickness

2020 ◽  
Vol 15 (1) ◽  
Author(s):  
Xiaowei Wang ◽  
Feng Liang ◽  
Degang Zhao ◽  
Zongshun Liu ◽  
Jianjun Zhu ◽  
...  
Keyword(s):  
Optical Properties ◽  
Quantum Wells ◽  
Layer Thickness ◽  
Stark Effect ◽  
Chemical Vapor ◽  
Multiple Quantum ◽  
Three Samples ◽  
Measurement Results ◽  
Cap Layer ◽  
The Difference

Abstract Three InGaN/GaN MQWs samples with varying GaN cap layer thickness were grown by metalorganic chemical vapor deposition (MOCVD) to investigate the optical properties. We found that a thicker cap layer is more effective in preventing the evaporation of the In composition in the InGaN quantum well layer. Furthermore, the quantum-confined Stark effect (QCSE) is enhanced with increasing the thickness of GaN cap layer. In addition, compared with the electroluminescence measurement results, we focus on the difference of localization states and defects in three samples induced by various cap thickness to explain the anomalies in room temperature photoluminescence measurements. We found that too thin GaN cap layer will exacerbates the inhomogeneity of localization states in InGaN QW layer, and too thick GaN cap layer will generate more defects in GaN cap layer.

scholarly journals Influence of the Bottom Color Modification and Material Color Modification Process on the Performance of Modified Poplar

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 660
Author(s):  
Qingqing Liu ◽  
Di Gao ◽  
Wei Xu
Keyword(s):  
Chemical Properties ◽  
Target Color ◽  
Modification Process ◽  
Red Color ◽  
The Difference ◽  
Pre Treatment ◽  
Physical And Chemical ◽  
Surface Differentiation ◽  
Color Modification ◽  
And Chemical Properties

According to the old surface coating process of European and American furniture, the surface of modified poplar is first differentiated pre-treatment, and then the bottom color modification and material color modification are respectively applied to the modified poplar after the surface differentiation treatment. The visual physical quantity and physical and chemical properties were measured and compared with mahogany, which is commonly used in old furniture in Europe and America to explore the effect of colorants and coloring steps, as well as different surface pretreatments on the coloring effect. Finally, it is concluded that continuous coloring operations can narrow the difference in brightness and red color value in the coloring layer of modified poplar and mahogany. Continuous coloring operations increase the difference between the yellow-green color values of modified poplar and mahogany. Therefore, the coloring difference between modified poplar and mahogany was affected by the colorant and coloring steps. Through color accumulation, the gap between the two in the target color coloring effect can be reduced, thereby reducing the difference between the coloring effect of modified poplar and mahogany.

Design of Measurement System of the Center of Gravity

2013 ◽  
Vol 706-708 ◽  
pp. 733-736
Author(s):  
Fang Li
Keyword(s):  
Measurement System ◽  
Center Of Gravity ◽  
Actual Position ◽  
Ideal Position ◽  
The Future ◽  
The Difference ◽  
New System ◽  
The Ideal

It is very difficult to confirm the position of the center of gravity irregular object.This paper introduces a new system,which can be used in measuring and adjusting of the center of gravity.The irregular object was put on the support parts,then the center of gravity was given.When the actual position was compared with the ideal position,the difference was given. Until actual position and ideal position were coincided,the machining was continuing. Matlab was programmed in this measure system. It will be applied widely in the future.

Physical and Chemical Sputtering at Very Low Ion Energy: the Importance of the Sputtering Threshold

1988 ◽  
Vol 129 ◽  
Author(s):  
Christoph Steinbruchel
Keyword(s):  
Threshold Energy ◽  
Surface Binding ◽  
Ion Energy ◽  
Chemical Sputtering ◽  
Surface Binding Energy ◽  
Physical Sputtering ◽  
Chemical Etch ◽  
Ion Energies ◽  
The Difference ◽  
Physical And Chemical

ABSTRACTA variety of data for physical etching (i.e. sputtering) and for ion-enhanced chemical etching of Si and SiO2 is analyzed in the very-low-ion-energy regime. Bombardment by inert ions alone, by reactive ions, and by inert ions in the presence of reactiveneutrals is considered. In all cases the etch yield follows a square root dependence on the ion energy all the way down to the threshold energy for etching. At the same time, the threshold energy has a non-negligible effect on the etch yield even at intermediate ion energies. The difference between physical and ion-enhanced chemical etch yields can be accounted for by a reduction in the average surface binding energy of the etch products and a corresponding reduction in the threshold energy for etching. These results suggest that, in general, the selectivity for ion-enhanced etch processes relative to physical sputtering can be increased significantly at low ion energy.

scholarly journals Molecular gas in the northern nucleus of Mrk 273: Physical and chemical properties of the disc and its outflow

2018 ◽  
Vol 617 ◽  
pp. A20 ◽  
Author(s):  
R. Aladro ◽  
S. König ◽  
S. Aalto ◽  
E. González-Alfonso ◽  
N. Falstad ◽  
...  
Keyword(s):  
Chemical Properties ◽  
Far Infrared ◽  
Molecular Gas ◽  
Dense Gas ◽  
Dynamical Mass ◽  
North West ◽  
North East ◽  
Dust Temperature ◽  
The Difference ◽  
Physical And Chemical

Aiming to characterise the properties of the molecular gas in the ultra-luminous infrared galaxy Mrk 273 and its outflow, we used the NOEMA interferometer to image the dense-gas molecular tracers HCN, HCO+, HNC, HOC+ and HC3N at ∼86 GHz and ∼256 GHz with angular resolutions of 4ʺ̣9 × 4ʺ̣5 (∼3.7 × 3.4 kpc) and 0ʺ̣61 × 0ʺ̣55 (∼460 × 420 pc). We also modelled the flux of several H2O lines observed with Herschel using a radiative transfer code that includes excitation by collisions and far-infrared photons. The disc of the Mrk 273 north nucleus has two components with decoupled kinematics. The gas in the outer parts (R ∼ 1.5 kpc) rotates with a south-east to north-west direction, while in the inner disc (R ∼ 300 pc) follows a north-east to south-west rotation. The central 300 pc, which hosts a compact starburst region, is filled with dense and warm gas, and contains a dynamical mass of (4 −5) × 109 M⊙, a luminosity of L′HCN = (3–4) × 108 K km s−1 pc2, and a dust temperature of 55 K. At the very centre, a compact core with R ∼ 50 pc has a luminosity of LIR = 4 × 1011 L⊙ (30% of the total infrared luminosity), and a dust temperature of 95 K. The core is expanding at low velocities ∼50–100 km s−1, probably affected by the outflowing gas. We detect the blue-shifted component of the outflow, while the red-shifted counterpart remains undetected in our data. Its cold and dense phase reaches fast velocities up to ∼1000 km s−1, while the warm outflowing gas has more moderate maximum velocities of ∼600 km s−1. The outflow is compact, being detected as far as 460 pc from the centre in the northern direction, and has a mass of dense gas ≤8 × 108 M⊙. The difference between the position angles of the inner disc (∼70°) and the outflow (∼10°) indicates that the outflow is likely powered by the AGN, and not by the starburst. Regarding the chemistry in Mrk 273, we measure an extremely low HCO+/HOC+ ratio of 10 ± 5 in the inner disc of Mrk 273.

TRUE AND APPARENT METABOLIZABLE ENERGY VALUES FOR POULTRY OF CANADIAN WHEATS AND OATS MEASURED BY BIOASSAY AND PREDICTED FROM PHYSICAL AND CHEMICAL DATA

1977 ◽  
Vol 57 (2) ◽  
pp. 365-374 ◽  
Author(s):  
I. R. SIBBALD ◽  
K. PRICE
Keyword(s):  
Metabolizable Energy ◽  
Chemical Data ◽  
Accuracy And Precision ◽  
Apparent Metabolizable Energy ◽  
The Difference ◽  
Variation Explained ◽  
Predicted Values ◽  
Naked Oats ◽  
Physical And Chemical ◽  
Better Than

Thirty samples of wheat and 28 samples of oats were assayed for true and apparent metabolizable energy (TME, AME). Within grains, the difference TME−AME increased with decreasing AME values; there is evidence that this trend is associated with reduced voluntary consumption of AME assay diets containing low energy grains. The TME and AME data were compared with ME values predicted from physical and chemical data describing the grains. Previously published prediction equations were tested and new equations were derived. Comparisons between predicted and observed data suggested that both the TME and AME values of wheat were predicted with insufficient accuracy and precision for practical use. Similar comparisons using the oat data showed high correlations between observed and predicted values, although the predictions were no more accurate than for wheat; however, when data describing four samples of naked oats were removed, the correlations were reduced substantially. Comparisons involving data for the hulled oats indicated that most equations were able to predict AME better than TME. Multiple regression analysis was used to identify those combinations of variables best able to predict TME data. No combination of variables was best for both wheat and oats. The combinations of variables used in published equations performed quite well. With four variables, the percentage of the TME variation explained was as high as 52 for wheat, 82 for oats and 64 for hulled oats. Predictions based on air-dry data are associated with higher correlations than those based on dry matter data, but the air-dry predictions are the less useful in practice. The reason for this is discussed.

scholarly journals Relationships between physical and chemical characteristics and calculated metabolizable energy values in barley and oats with highly variable volume weights

1978 ◽  
Vol 50 (3) ◽  
pp. 276-284
Author(s):  
Maija-Liisa Salo
Keyword(s):  
Crude Protein ◽  
Starch Content ◽  
Metabolizable Energy ◽  
Chemical Characteristics ◽  
Crude Fibre ◽  
Variable Volume ◽  
Physical And Chemical Characteristics ◽  
Volume Weight ◽  
The Difference ◽  
Physical And Chemical

61 samples of barley with a volume weight of 38—75 kg/hl, and 49 oat samples with a volume weight of 40—65kg/hl were analyzed for physical and chemical characteristics. The approximate metabolizable energy (ME) value was calculated from the composition. The physical characteristics varied more, but the starch content less, in barley than in oats. There was also a negative correlation between starch and crude protein, and ether extract level in barley, but not in oats. Therefore the difference between the ME values of the best and the poorest samples was only 12% for barley, but 27 % for oats. Both the starch and the crude protein content predicted the ME value well: R2 of starch was 78—94 %, and that of crude fibre 55—84 %. The volume weight still gave a good indication for barley, but not at all for oats.

scholarly journals Investigation on compatibility of PLA/PBAT blends modified by epoxy-terminated branched polymers through chemical micro-crosslinking

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Bo Wang ◽  
Yujuan Jin ◽  
Kai’er Kang ◽  
Nan Yang ◽  
Yunxuan Weng ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Glass Transition ◽  
Sem Analysis ◽  
Branched Polymers ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
The Difference ◽  
Physical And Chemical ◽  
The Impact

AbstractIn this study, a type of epoxy-terminated branched polymer (ETBP) was used as an interface compati- bilizer to modify the poly lactic acid (PLA)/poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30) blends. Upon addition of ETBP, the difference in glass transition temperature between PLA and PBAT became smaller. By adding 3.0 phr of ETBP, the elongation at break of the PLA/PBAT blends was found increased from 45.8% to 272.0%; the impact strength increased from 26.2 kJ·m−2 to 45.3 kJ·m−2. In SEM analysis, it was observed that the size of the dispersed PBAT particle decreased with the increasing of ETBP content. These results indicated that the compatibility between PLA and PBAT can be effectively enhanced by using ETBP as the modifier. The modification mechanism was discussed in detail. It proposes that both physical and chemical micro-crosslinking were formed, the latter of which was confirmed by gel content analysis.

A lotus-inspired janus hybrid film enabled by interfacial self-assembly and in situ asymmetric modification

2018 ◽  
Vol 54 (91) ◽  
pp. 12804-12807 ◽  
Author(s):  
Yun Liang ◽  
Jiangwei Shi ◽  
Peng Xiao ◽  
Jiang He ◽  
Feng Ni ◽  
...  
Keyword(s):  
Self Assembly ◽  
Hybrid Film ◽  
Water Interface ◽  
Assembly Process ◽  
Lotus Leaf ◽  
Air Interface ◽  
Oil Water

A lotus leaf inspired Janus hybrid film was exquisitely fabricated through a self-assembly process on the water/air interface with subsequent in situ asymmetric modification at the oil/water interface. The interfacial asymmetric decoration strategy thus provides a novel pathway for achieving a 2D Janus hybrid film with asymmetric wettability and functionality.

Sign in / Sign up

Export Citation Format

Share Document