Mechanical Properties of Composites with Geopolymer Matrices Reinforced by Basalt Fabric

2019 ◽  
Vol 889 ◽  
pp. 289-293
Author(s):  
Iva Petríková ◽  
Bohdana Marvalová ◽  
Jiří Lampa
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Tensile Tests ◽  
Bending Properties ◽  
Bending Tests ◽  
Three Point Bending ◽  
Geopolymer Matrix ◽  
Weave Fabric ◽  
Static Tensile ◽  
Properties Of Composites

The tensile and bending properties of composite materials with geopolymer matrix reinforced by layers of basalt plain weave fabric were investigated experimentally. We present the results of the quasi-static tensile tests and the quasi-static and cyclic three-point bending tests. The composite panels were made by hand laying with subsequent vacuuming. The plates were stayed in a compression press and left in a compressed state for a month. After 5 months the samples were made from the plates and subjected to tests. The material behaves as linear almost to the failure, which occurred at tensions of about 100 MPa. The elastic modulus is between 6000 and 7000 MPa.

Effects of Bending Cyclic Load on Mechanical Properties of 2D Carbon Cloth Laminated C/C Composites

2012 ◽  
Vol 157-158 ◽  
pp. 792-795 ◽  
Author(s):  
Xi Yang ◽  
He Jun Li ◽  
Kua Hai Yu
Keyword(s):  
Mechanical Properties ◽  
Cyclic Load ◽  
Room Temperature ◽  
Chemical Vapor ◽  
Cyclic Fatigue ◽  
Fatigue Tests ◽  
Carbon Cloth ◽  
Bending Tests ◽  
Three Point Bending ◽  
Properties Of Composites

Bending cyclic fatigue tests of 2D laminated C/C composites were conducted under load control at a sinusoidal frequency of 10 Hz. And three-point bending tests of fatigued specimens with various cycles were conducted at room temperature to evaluate the effects of cyclic load on mechanical properties. 2D C/C specimens were prepared by an isothermal chemical vapor deposition (CVD) process. The mechanical properties of composites were improved after cyclic loading at most the flexural strength by about 46% and the modulus 38%. The results show that the flexural properties of C/C composites were enhanced with the increase in fatigue cycles. It is suggested that the weakened interface between matrix and fibers by cyclic load play important roles in enhancing the property of C/C composites.

Investigation of The Elastic Modulus of Sol-Gel Derived Titania Using Three-Point Bending Tests

1996 ◽  
Vol 436 ◽  
Author(s):  
Å. K. Jämting ◽  
J. M. Bell ◽  
M. V. Swain
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Sol Gel ◽  
Bending Tests ◽  
Three Point Bending ◽  
Compositional Uniformity ◽  
Titania Films ◽  
Sol Gel Films ◽  
Film Porosity ◽  
Thickness Measurements

AbstractThere is increasing interest in the use of sol-gel derived films in tribological applications, and this necessitates an understanding of the mechanical properties of these films. Few investigations into the mechanical properties of sol-gel films have been undertaken, and in this study we have concentrated on measurement of the elastic modulus of sol-gel derived titania films as a preliminary stage in a full investigation of stress in sol-gel deposited thin films. Sol-gel films are often very thin and in order to understand the influence of the substrate on the measured elastic modulus, we have used a multiple coating technique to deposit titania films of increasing thickness on various substrates. A three point bending apparatus is used to measure the elastic modulus. The three-point bending apparatus has very low load and displacement measuring capabilities as is required for the very thin sol-gel films. Measurements of the compositional uniformity of the films have been performed using RBS, and this has been combined with film thickness measurements to determine the film porosity. This information ensures that the measured properties relate to intrinsic film properties. The results of all these measurements will be presented.

scholarly journals Influence of Polymer Coatings on the Mechanical Properties of Steel Samples in Tensile and Bending Tests

2021 ◽  
Vol 12 (5) ◽  
pp. 542-548
Author(s):  
O.A. Pashkov
Keyword(s):  
Mechanical Properties ◽  
Theoretical Study ◽  
Tensile Tests ◽  
Polymer Coatings ◽  
Theory Of Elasticity ◽  
Steel Plates ◽  
Bending Tests ◽  
Three Point Bending ◽  
Coated Plate ◽  
Classical Models

: An experimental and theoretical study of the effect of polymer coatings on an epoxy-polyester base on the mechanical properties of samples in the form of steel plates has been carried out. It is shown that, despite the fact that the thickness of the coatings is only 100 μm, they have a significant effect on the mechanical properties of plates up to 1,5 mm thick, leading to a decrease in Young's modulus, tensile strength and ultimate deformations of the samples. It was shown that the elastic modulus of the coated plate cannot be determined unambiguously from tests for central tension and three-point bending. In bending tests, there is a more significant reduction in plate stiffness compared to tensile tests. This effect is confirmed by calculations within the framework of classical models of the theory of elasticity.

Flexural Properties of Polyamides: Influence of Strain Rate, Friction and Moulding-Induced Anisotropy

2014 ◽  
Vol 601 ◽  
pp. 29-32
Author(s):  
Dan Andrei Serban ◽  
Tudor Voiconi ◽  
Liviu Marsavina ◽  
Vadim V. Silberschmidt
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Tensile Tests ◽  
Flexural Properties ◽  
Induced Anisotropy ◽  
Flexural Behaviour ◽  
Bending Tests ◽  
Three Point Bending ◽  
Cooling Conditions

In recent years, advances in material testing equipment caused the determination of mechanical properties by means of three-point bending tests to lose ground in detriment to more accurate tensile tests. However, if components undergo bending deformation in service, the identification of the materials flexural behaviour is essential. The investigated material is a thermoplastic polymer, test specimens being cut in prismatic shapes from injected sheets, which present a variation in properties due to cooling conditions. This paper presents results of three-point bending tests with emphasis on the influence of strain rate and anisotropy on flexural strength and chord modulus. Results show an increase in flexural properties with strain rate and a considerable influence of anisotropy on mechanical properties.

Study of RIN-Insulation Mechanical Properties for High Voltage Inputs

2021 ◽  
Vol 316 ◽  
pp. 942-948
Author(s):  
Alexander Demidov ◽  
Myrzamamat Karimbekov ◽  
Regina Rodyakina
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
High Voltage ◽  
Tensile Tests ◽  
Climatic Conditions ◽  
Insulation Material ◽  
Working Ability ◽  
Bending Tests ◽  
Three Point Bending ◽  
Strength Tests

This paper presents the results of mechanical properties study for samples of RIN-insulation material (Resin Impregnated Nonwoven – non-woven resin impregnated fabric) for high-voltage inputs at various temperatures, determined by three-point bending tests, impact strength tests and tensile tests with registration of test diagrams. The mechanical properties of RIN-insulation, which ensure working ability of the whole construction of high-voltage inputs, operating in difficult climatic conditions, are determined.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Mechanical Properties of Flat Braided Composites With a Circular Hole

1999 ◽  
Author(s):  
Takeru Ohki ◽  
Shinya Ikegaki ◽  
Ken Kurasiki ◽  
Hiroyuki Hamada ◽  
Masaharu Iwamoto
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Circular Hole ◽  
Fracture Behavior ◽  
Fatigue Property ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Braided Composites ◽  
Static Tensile ◽  
The One

Abstract In this study, fracture behavior and strength in the flat braided bar with a circular hole were investigated by static and fatigue test. Two type of specimens were prepared. They are a braided flat bar with an integrally-formed braided hole and a braided flat bar with a machined hole. Moreover, we also examined a specimen that had a metal pin inserted at the circular hole. This specimen was subjected to a static tensile test. The results of the tensile tests indicate that the strength of the flat bar with a braided hole was larger than that of the one with the machined hole. Furthermore, from the results of the fatigue tests, the flat bar with the braided hole showed higher fatigue property than that of the one with the machined hole.

scholarly journals Mechanical Properties of Sigma 1140+ Sic Fibres Prior and after Composite Processing

2000 ◽  
Vol 9 (4) ◽  
pp. 096369350000900 ◽  
Author(s):  
C. Gonzalez ◽  
J. Llorca
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Elastic Modulus ◽  
Weibull Modulus ◽  
Fibre Diameter ◽  
Tensile Tests ◽  
Fibre Strength ◽  
Composite Processing ◽  
Scanning Electron

The effect of processing on the mechanical properties of Sigma 1140+ SiC fibres was studied through tensile tests carried out on pristine Sigma 1140+ SiC fibres and on fibres extracted from a Ti-6A1-4V-matrix composite. The elastic modulus and the tensile strength were computed after measuring carefully the fibre diameter. The characteristic fibre strength was reduced by 20% and the Weibull modulus by half during composite processing. The analysis of the fracture surfaces in the scanning electron microscope showed that the strength-limiting defects were located around the tungsten core in pristine fibres and predominantly at the surface in fibres extracted from the composite panels. These latter defects were nucleated by the mechanical stresses generated on the fibres during the panel consolidation.

scholarly journals Incidence of mercerization treatment in the mechanical properties of bamboo fibre bundles "Guadua Angustifolia Kunth" from colombian origin

DYNA ◽  
2019 ◽  
Vol 86 (210) ◽  
pp. 156-163 ◽  
Author(s):  
Leidy Johana Quintero Giraldo ◽  
Luis Javier Cruz ◽  
Jaime Alexis García ◽  
Alejandro Alcaraz ◽  
Eugenia González ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Tensile Tests ◽  
Good Correspondence ◽  
Fibre Bundles ◽  
Bamboo Fibre ◽  
Untreated Fibre ◽  
Mercerization Treatment ◽  
Mechanical Extraction

In this article, bamboo fibre bundles of "Guadua Angustifolia Kunth" specie were isolated from different locations of the basa zone: upper, middle and lower, through mechanical extraction method. The elastic modulus and the tensile strength were obtained with preliminary tensile tests. Applying the statistical analysis known as ANOVA, it was determined that the mechanical properties are similar in all the extension of the basa zone. From there, fibre bundles were extracted randomly, and a part of the fibre bundles was treated with NaOH (mercerization). Later, tensile tests with different calibration lengths were made for calculate the elastic modulus and the tensile strength of the treated and untreated fibre bundles. Best results belonged to the treated fibre bundles. A good correspondence between the results obtained in this work and the results reported in the literature was concluded. 

scholarly journals Comparison of Mechanical Properties of Hemp-Fibre Biocomposites Fabricated with Biobased and Regular Epoxy Resins

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5720 ◽  
Author(s):  
Vicente Colomer-Romero ◽  
Dante Rogiest ◽  
Juan Antonio García-Manrique ◽  
Jose Enrique Crespo
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resins ◽  
Raw Materials ◽  
Green Composites ◽  
Bending Tests ◽  
Three Point Bending ◽  
Reinforced Plastics ◽  
Structural Applications ◽  
Glass Fibre Reinforced ◽  
Glass Fibre Reinforced Plastics

Bio- and green composites are mainly used in non-structural automotive elements like interior panels and vehicle underpanels. Currently, the use of biocomposites as a worthy alternative to glass fibre-reinforced plastics (GFRPs) in structural applications still needs to be fully evaluated. In the current study, the development of a suited biocomposites started with a thorough review of the available raw materials, including both reinforcement fibres and matrix materials. Based on its specific properties, hemp appeared to be a very suitable fibre. A similar analysis was conducted for the commercially available biobased matrix materials. Greenpoxy 55 (with a biocontent of 55%) and Super Sap 100 (with a biocontent of 37%) were selected and compared with a standard epoxy resin. Tensile and three-point bending tests were conducted to characterise the hemp-based biocomposite.

Sign in / Sign up

Export Citation Format

Share Document