Comparative Study of Phenol Adsorption from Aqueous Solution onto Four Kinds of Absorbents

2014 ◽  
Vol 1056 ◽  
pp. 134-137
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Xin Pang
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Fly Ash ◽  
Comparative Study ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Contact Time ◽  
Carbon Powder ◽  
Nay Zeolite ◽  
Phenol Adsorption

The absorbents including MnO2, fly ash, NaY zeolite and activated carbon powder were used to study the adsorption capacity of phenol. The effect of contact time and dosage of absorbents on the removal efficiency were investigated. The experimental results suggested that activated carbon powder is most effective absorbent, following as fly ash, MnO2 and NaY zeolite which the removal efficiency could reached 98.41%,77.65%, 60.19% and 24.13% at 90min respectively. The data indicated that the activated carbon powder was favorable for adsorption while NaY zeolite was unfit for absorbent of phenol from aqueous solution due to lower removal.

Microwave Preparation of Modified Activated Carbons for Phenol Adsorption in Aqueous Solution

2013 ◽  
Vol 726-731 ◽  
pp. 1883-1889
Author(s):  
Brim Stevy Ondon ◽  
Bing Sun ◽  
Zhi Yu Yan ◽  
Xiao Mei Zhu ◽  
Hui Liu
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Activated Carbons ◽  
Microwave Energy ◽  
Adsorptive Capacity ◽  
Obvious Effect ◽  
Phenol Adsorption ◽  
Adsorption Capacities ◽  
Modified Activated Carbons

Microwave energy was used to prepare modified activated carbons (GAC, GAC/MW, GAC/Ni, and GAC/Cu). The modified activated carbons were used for phenol adsorption in aqueous solution. The adsorption conditions were optimized. Adsorption capacities of the different modified activated carbons were evaluated. The effect of microwave pretreatment of activated carbons was investigated. A comparative study on the activated carbons adsorption capacities was also investigated. Under optimal conditions the results showed that there was no obvious effect on activated carbons adsorption when rising temperature and pH during the adsorption process. Stirring has a very high effect on the activated carbons adsorption capacity. The adsorption capacity of the modified activated carbons reaches 95%. MW/GAC, GAC/Ni and GAC/Cu adsorptive capacity was higher compared to the Granulated Activated Carbon (GAC) used as received. GAC treated with microwave energy has highest adsorption capacity. The adsorption capacity of GAC loaded with ion Ni2+ is higher than the activated carbon loaded with Cu2+. The untreated GAC has the lowest adsorption capacity. These results can be explained by the effect of microwave irradiation on GAC.The activated carbon loaded with Ni2+ adsorbs more microwave energy than the GAC loaded with Cu2+.

scholarly journals Removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones

2019 ◽  
Vol 6 (2) ◽  
pp. 81-88 ◽  
Author(s):  
Dariush Naghipour ◽  
Abdoliman Amouei ◽  
Kamran Taher Ghasemi ◽  
Kamran Taghavi
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Contact Time ◽  
Wastewater Treatment Plants ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Pine Cones ◽  
Adsorbent Dose

Background: Metoprolol (MTP) with its low biodegradability is one of the most dominant micropollutant in the effluent of wastewater treatment plants. The aim of this study was to investigate the removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones. Methods: The pine cones were activated using thermal activation method. Characteristics of the adsorbent were determined using Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM). In this study, the influent of different parameters such as pH, contact time, initial concentrations of metoprolol, adsorbent dose, temperature, adsorption isotherms, and kinetics were investigated. Results: The maximum removal efficiency of MTP (89.2%) was obtained at pH=8.5, adsorbent dose=1.5 g, contact time=60 min, and initial concentration=50 mg/L. By increasing the adsorbent dose, the removal efficiency also increased, but the adsorption capacity decreased, however, by increasing the initial concentration, the removal efficiency decreased, but the adsorption capacity increased. The isotherm experimental data for metoprolol was best fitted using the Langmuir model, and kinetic data were better described by pseudo-second-order kinetic model. The thermodynamic study indicated that the adsorption of MTP by the adsorbent was feasible, spontaneous, and endothermic. Conclusion: MTP removal by the activated carbon prepared from pine cones showed that this natural adsorbent is appropriate for removal of metoprolol from aqueous solutions regarding cost, efficiency, and production method.

scholarly journals Microcrystalline cellulose (MCC) as an adsorbent in copper removal from aqueous solution

2021 ◽  
Vol 1195 (1) ◽  
pp. 012022
Author(s):  
N A Khalil ◽  
N S Abdullah ◽  
A S A Rahman ◽  
H A Hamid ◽  
A N S Fizal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Microcrystalline Cellulose ◽  
Contact Time ◽  
Adsorption Process ◽  
Adsorption Parameters ◽  
Temperature Ranges ◽  
Higher Temperature ◽  
Lower Temperature

Abstract Many studies have been done on the natural adsorbent, natural/raw cellulose, modified cellulose and modified MCC as media for removing copper. However, the usage of unmodified microcrystalline cellulose (MCC) as an adsorbent to remove heavy metals contaminants such as copper from an aqueous solution is scarcely being explored. Thus, the current study was done to assess the performance of the MCC, without any modification, based on the adsorption capacity and the Cu removal efficiency under varied process parameters. The MCC was successfully used for Cu2+ or Cu (II) removal at pH < pH6. The adsorption parameters such as pH (1 to 6), contact time (0.5 to 24 hours), temperature (25 to 70 °C), initial Cu concentrations (1 to 5 mg/L) and MCC dosage (0.05 to 0.5 g) were significantly influenced the adsorption performance of the MCC. This study indicated the adsorption process occurred at pH ranging from pH 2.8 to 6 with 3 to 24 hours of duration were required to achieve the equilibrium condition. Lower temperature ranges (25 to 30 °C) were more favourable for adsorption than higher temperature ranges (40 to 70 °C). The increase in initial Cu concentration enhanced the adsorption capacity of MCC but decreased Cu removal. On the other hand, the increase in the MCC dosage resulted in the decreased adsorption capacity, however, increased Cu removal. MCC dosage of 0.225 g managed to remove Cu (II) with 95% efficiency at the initial Cu concentration of 1 mg/L, pH 5 and temperature 25 °C within 24 hours of contact time with 0.18 mg/g of adsorption capacity. Overall, high Cu removal efficiency (up to 95%) was achieved by the MCC which render its usage as adsorbent.

scholarly journals Adsorption of Chlorophenol from Aqueous Solution on Fluted and Commercial Activated Carbon

2012 ◽  
Vol 27 ◽  
pp. 1-10 ◽  
Author(s):  
O. A. Ekpete ◽  
M. Horsfall ◽  
T. Tarawou
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Sorption Capacity ◽  
Contact Time ◽  
Fluted Pumpkin ◽  
Adsorbate Concentration ◽  
Adsorption Data ◽  
Elovich Equation ◽  
Better Than

The adsorption of chlorophenol by an agro-based activated carbon prepared from fluted pumpkin stem waste was investigated to assess its possible use as adsorbent. The effect of pH, initial adsorbate concentration, adsorbent dosage and contact time were studied to identify adsorption capacity of the fluted activated carbon (FAC). The results were compared to a commercial activated carbon (CAC). Adsorption data were modelled with the Langmuir, Elovich and Dubinin-Radushkevich classical adsorption isotherms. The data fitted the Elovich isotherm model better than Langmuir and Dubinin-Radushkevich. According to the evaluation using Elovich equation showed the sorption capacity obtained for chlorophenol on fluted activated carbon as 47.62 mg/g and chlorophenol for commercial activated carbon as 38.46 mg/g. The data showed that fluted activated carbon derived from fluted pumpkin stem waste, an environmental nuisance in Nigeria could be converted to a useful activated carbon for chlorophenol removal in aqueous solution.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6435 J. Nepal Chem. Soc., vol. 27, 2011 p.1-10Uploaded date: 16 July, 2012

scholarly journals Evaluation of removal efficiency of residual diclofenac in aqueous solution by nanocomposite tungsten-carbon using design of experiment

2017 ◽  
Vol 76 (6) ◽  
pp. 1466-1473 ◽  
Author(s):  
M. H. Salmani ◽  
M. Mokhtari ◽  
Z. Raeisi ◽  
M. H. Ehrampoush ◽  
H. A. Sadeghian
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Design Of Experiment ◽  
High Efficiency ◽  
Carbon Powder ◽  
Batch Adsorption ◽  
Effective Parameters ◽  
Initial Concentration ◽  
Carbon Nanocomposite ◽  
Maximum Removal

Wastewater containing pharmaceutical residual components must be treated before being discharged to the environment. This study was conducted to investigate the efficiency of tungsten-carbon nanocomposite in diclofenac removal using design of experiment (DOE). The 27 batch adsorption experiments were done by choosing three effective parameters (pH, adsorbent dose, and initial concentration) at three levels. The nanocomposite was prepared by tungsten oxide and activated carbon powder in a ratio of 1 to 4 mass. The remaining concentration of diclofenac was measured by a spectrometer with adding reagents of 2, 2′-bipyridine, and ferric chloride. Analysis of variance (ANOVA) was applied to determine the main and interaction effects. The equilibrium time for removal process was determined as 30 min. It was observed that the pH had the lowest influence on the removal efficiency of diclofenac. Nanocomposite gave a high removal at low concentration of 5.0 mg/L. The maximum removal for an initial concentration of 5.0 mg/L was 88.0% at contact time of 30 min. The results of ANOVA showed that adsorbent mass was among the most effective variables. Using DOE as an efficient method revealed that tungsten-carbon nanocomposite has high efficiency in the removal of residual diclofenac from the aqueous solution.

scholarly journals Ricinus CommunisPericarp Activated Carbon Used as an Adsorbent for the Removal of Ni(II) From Aqueous Solution

2008 ◽  
Vol 5 (4) ◽  
pp. 761-769 ◽  
Author(s):  
S. Madhavakrishnan ◽  
K. Manickavasagam ◽  
K. Rasappan ◽  
P. S. Syed Shabudeen ◽  
R. Venkatesh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Activated Carbon ◽  
Contact Time ◽  
Metal Ion ◽  
Ricinus Communis ◽  
Ion Concentration ◽  
Batch Mode ◽  
Adsorption Data ◽  
Initial Ph

Activated carbon prepared from Ricinus communis Pericarp was used to remove Ni(II) from aqueous solution by adsorption. Batch mode adsorption experiments are carried out by varying contact time, metal-ion concentration, carbon concentration and pH to assess kinetic and equilibrium parameters. The adsorption data were modeled by using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity (Qo) calculated from the Langmuir isotherm was 31.15 mg/g of activated carbon at initial pH of 5.0±0.2 for the particle size 125-250 µm.

scholarly journals Adsorption of Copper Ions (Cu++) in Aqueous Solution Using Activated Carbon and Biosorbent from Indian Jujube (Ziziphus mauritiana) Seed Hulls

2020 ◽  
pp. 13-24
Author(s):  
Harouna Massai ◽  
Djakba Raphael ◽  
Mouhamadou Sali
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Copper Ions ◽  
Carbon Powder ◽  
Ziziphus Mauritiana ◽  
Batch Mode ◽  
Freundlich Model ◽  
Jar Test ◽  
Standard Procedures ◽  
Indian Jujube

The present work aimed at mitigating the level of copper ions (Cu++) by adsorption in aqueous solution using activated carbon powder (AC) and biosorbent (BS) from the Indian jujube seed hulls. The AC and BS were prepared from the Indian jujube seed hulls and characterized    using standard procedures. In addition, the adsorption effects of Indian jujube seed hulls through the AC and BS were carried out using jar test experiment (batch mode) at different pH (1, 2, 3, and 4), ionic strengths (100-600 mg/L) and stirring speed (120rpm). Therefore, it was found that the adsorption time at equilibrium were 10 and 5 minutes respectively for the AC and the BS.  Furthermore, it was found that the reduction of copper ions were 99.40% and 73.08% for aqueous solutions of 100 ppm and 500 ppm respectively at the equilibrium state. It was also revealed that when the mass of the AC or the BS increases, the quantities of ions adsorbed per gram decrease. The maximum pH of adsorption for the AC was found to be pH=1, while it was found to be pH=4 for the BS. The Freundlich model indicated that the adsorption of copper ions by the Indian jujube is linear while the Temkin and Dubinin-Kagana-Radushkevich models described the adsorption as a physical reaction. It was finally observed that the adsorption of copper ions by the AC and the BS from Indian jujube seed hulls influenced by the addition of some concentration of NaCl.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

Sign in / Sign up

Export Citation Format

Share Document