Experimental Research on Deformation Characteristics and Energy Change of Rock under Different Unloading Rates of Confining Pressures

2011 ◽  
Vol 243-249 ◽  
pp. 2885-2888
Author(s):  
Xian Min Han ◽  
Shou Ding Li
Keyword(s):  
Rock Mass ◽  
Energy Release ◽  
Rock Burst ◽  
Experimental Research ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Deformation Characteristics ◽  
Confining Pressures ◽  
Unloading Rate ◽  
Unloading Confining Pressure

Experiments of unloading confining pressure of rock were conducted to reveal deformation characteristics of rock mass under different excavation intension in thigh geostress condition. It were concluded from tests that volumetric strain of rock is inverse proportional to unloading rate. The smaller the unloading rate, the bigger the ductility of rock. Energy release are bigger under high unloading rate than that under low unloading rate. That means that tendency of rock burst turn smaller when unloading rates decrease.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

scholarly journals The meso-fracturing mechanism of marble under unloading confining pressure paths and constant axial stress

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Linna Sun ◽  
Liming Zhang ◽  
Yu Cong ◽  
Yaduo Song ◽  
Keqiang He
Keyword(s):  
Shear Failure ◽  
Axial Stress ◽  
Confining Pressure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Confining Pressures ◽  
Tension Cracks ◽  
Trial And Error Method ◽  
Unloading Confining Pressure ◽  
Fracturing Mechanism

AbstractFailure tests on marble during unloading confining-pressure under constant axial stress and simulations with the particle flow code were performed. The influence mechanism of the unloading rate of the confining pressure, initial unloading stress, and confining pressure on the failure characteristics of, and crack propagation in, marble was studied. By using the trial-and-error method, the conversion relationship between the unloading rates of confining pressures in laboratory tests and numerical simulations was ascertained. Micro-cracks formed in the unloading process of confining pressure are dominated by tension cracks, accompanied by shear cracks. The propagation of shear cracks lags that of tension cracks. As the confining pressure is increased, more cracks occur upon failure of the samples. The proportion of shear cracks increases while that of tension cracks decreases. The failure mode of samples undergoes a transition from shear-dominated failure to conjugated shear failure.

scholarly journals Acoustic Emission Simulation on Coal Specimen Subjected to Cyclic Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Huiqiang Duan ◽  
Depeng Ma
Keyword(s):  
Numerical Simulation ◽  
Acoustic Emission ◽  
Cyclic Loading ◽  
Confining Pressure ◽  
Rock Masses ◽  
Coal Specimen ◽  
Cycle Number ◽  
Confining Pressures ◽  
Unloading Rate ◽  
Ae Counts

The damage and failure state of the loaded coal and rock masses is indirectly reflected by its acoustic emission (AE) characteristics. Therefore, it is of great significance to study the AE evolution of loaded coal and rock masses for the evaluation of damage degree and prediction of collapse. The paper mainly represents a numerical simulation investigation of the AE characteristics of coal specimen subjected to cyclic loading under three confining pressures, loading-unloading rates, and valley stresses. From the numerical simulation tests, the following conclusions can be drawn: (1) The final cycle number of coal specimen subjected to cyclic loading is significantly influenced by the confining pressure, followed the valley stress. With the increase in confining pressure or valley stress, the cycle number tends to increase. However, the loading-unloading rate has a little influence on it. (2) The AE counts of coal specimen subjected to cyclic loading are greatly influenced by the confining pressure and the valley stress. With the increase in the confining pressure, the cumulative AE counts at the 1st cycle tend to increase but decrease at a cycle before failure; with the decrease in the valley stress, the cumulative AE counts per cycle increase in the relatively quiet phase. However, the loading-unloading rate has a little influence on it. (3) The failure mode of coal specimen subjected to cyclic loading is significantly influenced by the confining pressure. Under the uniaxial stress state, there is an inclined main fractured plane in the coal specimen, under the confining pressures of 5 and 10 MPa, the coal specimen represents dispersion failure. The loading-unloading rate and valley stress have little influence on it. (4) The AE ratio is proposed, and its evolution can better reflect the different stages of coal specimen failure under cyclic loading. (5) The influence of confining pressure on the broken degree of coal specimen subjected to cyclic loading is analyzed, and the higher the confining pressure, the more broken the failed coal specimen.

scholarly journals Experimental Study on Triaxial Unloading Failure of Deep Composite Coal-Rock

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Xin Li ◽  
Hao Li ◽  
Zhen Yang ◽  
Zhongxue Sun ◽  
Jiayu Zhuang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Failure Criterion ◽  
Confining Pressure ◽  
Exponential Relationship ◽  
Partial Fracture ◽  
Triaxial Compressive Strength ◽  
Confining Pressures ◽  
Unloading Rate ◽  
Coal Rock ◽  
And Control

With the deep mining of coal, the phenomenon of high ground stress is more likely to cause dynamic disaster. In view of the above problems, this paper takes the unloading process of coal mining as the background to study the effects of mining rates under different conditions on the mechanical properties and triaxial failure criterion of composite coal-rock, so as to provide a theoretical basis for the prevention and control of dynamic disasters in coal mines. The composite coal-rock models with a composite ratio of 1 : 1 : 1 were tested under different unloading rates or confining pressures. The results show that the triaxial unloading process of coal-rock can be divided into five stages: compaction, single elasticity, elastic-plastic unloading, partial fracture, and complete fracture. In this paper, the failure criterion of composite coal-rock triaxial unloading is derived. The unloading rate has an exponential relationship with the triaxial compressive strength, and the relationship between initial confining pressure and compressive strength is linear. The triaxial compressive strength is determined by both. The peak strains ε of all samples under different unloading conditions were around 0.01. And initial confining pressure had an influence on the strain variation trend during the unloading of composite coal-rock. The higher the initial confining pressure, the greater the elastic modulus. In addition, an increase of initial confining pressure led to the increase of the total energy converted into dissipated part in the process of fracture and caused the obvious increase of the rebound characteristics of the curve. However, the unloading rate had no influence on the strain trend.

scholarly journals Experimental Research into the Evolution of Permeability of Sandstone under Triaxial Compression

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5065
Author(s):  
Liming Zhang ◽  
Shengqun Jiang ◽  
Jin Yu
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Testing Machine ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Rate Of Change ◽  
Peak Strength ◽  
Sudden Increase ◽  
Seepage Pressure ◽  
Confining Pressures

Failure tests on sandstone specimens were conducted under different confining pressures and seepage pressures by using an MTS triaxial rock testing machine to elucidate the corresponding correlations of permeability and characteristic stress with confining pressure and pore pressure during deformation. The results indicate that permeability first decreases and presents two trends, i.e., a V-shaped increase and an S-shaped trend during the non-linear deformation stage. The greater the seepage pressure, the greater the initial permeability and the more obvious the V-shaped trend in the permeability. As the confining pressure was increased, the trend in the permeability gradually changed from V- to S-shaped. Compared with the case at a high confining pressure, the decrease of permeability occurred more quickly, the rate of change becomes greater, and the sudden increase observed in the permeability happened earlier under lower confining pressures. Within the range tested, confining pressure exerted a greater effect on the permeability than the seepage pressure. In comparison with the axial strain, volumetric strain better reflected changes in permeability during compaction and dilation of sandstone. The ratio of crack initiation stress to peak strength ranged from 0.37 to 0.50, while the ratio of dilation stress to peak strength changed from 0.58 to 0.72. Permeabilities calculated based on Darcy and non-Darcy flow changed within the same interval, while the change in permeability was different.

Research on Post-Peak Characteristics of Elastic-Plastic Strain-Softening Model Based on Mohr-Coulomb Strength Criterions

2011 ◽  
Vol 261-263 ◽  
pp. 1439-1443
Author(s):  
Shao Qing Niu ◽  
Shuang Suo Yang ◽  
Lei Cui
Keyword(s):  
Rock Mass ◽  
Strain Softening ◽  
Triaxial Compression ◽  
Dynamic Change ◽  
Confining Pressure ◽  
Strength Parameters ◽  
Underground Engineering ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Damage Extent

Considering the characteristic that rock mass can transform from brittleness to plasticity and the dynamic change of post-peak strength parameters of the rock mass, the invariability of elastic modulus and poisson's ratio, constitutive model of rock mass could be described with the characteristic that strength parameters obey different Mohr-Coulomb failure criterions under different plastic strains. This model may reflect the post-peak subsequent characteristics of rock mass and the fact that rock mass can transform from brittleness to plasticity with the increase of confining pressure. Numerical calculation is applied to simulate the triaxial compression test under different confining pressures and underground engineering example, which proves that this model has the characteristic of reflecting the damage extent of surrounding rock.

scholarly journals Investigating the Permeability of Marble under Moderate Pressure and Temperature

Geofluids ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Jianping Yang ◽  
Weizhong Chen ◽  
Diansen Yang ◽  
Hongming Tian
Keyword(s):  
Volumetric Strain ◽  
Strain Curve ◽  
Confining Pressure ◽  
Crystalline Rock ◽  
Mechanical Tests ◽  
Moderate Pressure ◽  
Test Results ◽  
Permeability Evolution ◽  
Confining Pressures ◽  
Linkage Model

The permeability of intact marble samples collected from the depth of 1.6 km in southwestern China is investigated under moderate confining pressures and temperatures. No microcracks initiate or propagate during the tests, and the variation of permeability is due to the change of aperture of microcracks. Test results show a considerable decrease of permeability along with confining pressure increase from 10 to 30 MPa and temperature increase from 15 to 40°C. The thermal effect on the permeability is notable in comparison with the influence of the stress. A simple permeability evolution law is developed to correlate the permeability and the porosity in the compressive regime based on the microphysical geometric linkage model. Using this law, the permeability in the compressive regime for crystalline rock can be predicted from the volumetric strain curve of mechanical tests.

scholarly journals Attenuation Law of Stress Waves in Cracked Rock Mass under Different Confining Pressures

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Xiaoming Lou ◽  
Rui Luo ◽  
Jin Yu
Keyword(s):  
Rock Mass ◽  
Attenuation Coefficient ◽  
Crack Width ◽  
Confining Pressure ◽  
Test System ◽  
Stress Waves ◽  
Attenuation Law ◽  
Deep Rock ◽  
Confining Pressures ◽  
Crack Angle

Through theoretical analysis and indoor model tests, this paper explores the attenuation law of stress waves in the intact confined rock mass and cracked rock mass under different confining pressures, especially the relationship between the stress attenuation coefficient, crack width, and crack angle, respectively. The tests were carried out on a triaxial test system for deep rock mass, which supports both static and dynamic loading. The research results show that the physical attenuation of the stress wave in the intact rock mass first decreases and then increases with the increase of the confining pressure and decreases with the increase of crack width. The attenuation coefficient of stress waves in the cracked rock mass depends on the crack angle and crack width. Specifically, the coefficient is negatively correlated with crack width; under no confining pressure, the coefficient decreases with the increase of the crack angle; when the confining pressure is on a moderate level, the coefficient increases with the crack angle; when the confining pressure exceeds the uniaxial intensity by 34%, the coefficient decreases again with the increase of the crack angle. The theoretical propagation equation of stress waves at the crack, which was derived from the propagation attenuation mechanism of stress waves in the cracked rock mass, was proved feasible through the comparison against the experimental results.

scholarly journals Study on Rock Burst Event Disaster and Prevention Mechanisms of Hard Roof

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Nan Zhou ◽  
Hengfeng Liu ◽  
Jixiong Zhang ◽  
Hao Yan
Keyword(s):  
Rock Mass ◽  
Energy Release ◽  
Rock Burst ◽  
Strain Energy ◽  
Roof Rock ◽  
Coal Mass ◽  
Energy Evolution ◽  
Hard Roof ◽  
Working Face ◽  
Coal Rock

Coal mining under hard roofs is jeopardized by rock burst-induced hazards. In this paper, mechanisms of hard roof rock burst events and key techniques for their prevention are analyzed from the standpoint of energy evolution within geological conditions typical of the hard roofs found in Chinese coal mines. Equations used to calculate the total strain energy densities of the coal-rock mass and hard roof working face are derived. Moreover, several failure-causing energy evolution rules are analyzed under various conditions. Various rock roof and coal mass thicknesses and strengths are considered, and a method of preventing hard roof rock burst events is proposed. The results obtained show that rock burst events can be facilitated by high stress concentrations, significant accumulation of strain energy in the coal-rock mass, and rapid energy release during roof breakage. The above conditions are subdivided into two classes: energy accumulation and energy release. The total strain energies of the coal mass and working faces in the roof are positively correlated with the roof thickness, roof strength, and coal mass strength. The coal mass strength primarily influences the overall accumulation of energy in the working face, and it also has the largest effect on the total energy release (i.e., the earthquake magnitude).

Mechanical Deformation Characteristics of Hard Rock in Deep Excavation

2011 ◽  
Vol 90-93 ◽  
pp. 61-66 ◽  
Author(s):  
Ying Hui Lv ◽  
Bin Yan
Keyword(s):  
Rock Mass ◽  
Simulation Analysis ◽  
Volumetric Strain ◽  
Mechanical Deformation ◽  
Deformation Characteristics ◽  
Deep Excavation ◽  
Tunnel Excavation ◽  
Failure Characteristics ◽  
Excavation Process ◽  
Coulomb Criterion

In the process of deep tunnel excavation, the surrounding rock mass, which often endures high initial geo-stress, is in the state of typical unloading. As the adjustment of stress induced by excavation, rock mass behaves a peculiar kind of mechanical deformation characteristics, different from those in loading conditions. As thus, a series of representative unloading tests on hard granite from DaGangShan power station in China, which is being excavation at 1500 meters deep below earth surface, are carried out to simulate dynamically excavation process for studying the peculiar mechanical deformation characteristics. On the basis of unloading tests, a series of research results are acquired as follows： (1) Under unloading condition, lateral deformation occurs in the unloading direction and volumetric strain changes from compression deformation to dilation deformation. (2) Under unloading condition, hard granites behave brittle failure and Mogi-coulomb criterion can well describe the failure characteristics. (3) According to curves of unloading tests, the constitutive model is deduced for simulation analysis.

Sign in / Sign up

Export Citation Format

Share Document