Grain Size Control and Ethanol Sensing Properties of Calcined SnO2 Nanoparticles

2011 ◽  
Vol 266 ◽  
pp. 76-79
Author(s):  
Yu Wang ◽  
Xiao Lin Jia ◽  
Lin Dong ◽  
Shao Kang Guan
Keyword(s):  
Sno2 Nanoparticles ◽  
Sol Gel ◽  
Average Particle Size ◽  
Size Control ◽  
High Sensitivity ◽  
Average Particle ◽  
Nanocrystal Growth ◽  
Grain Size Control ◽  
Concentration Detection Limit ◽  
Ethanol Sensing

SnO2 nanoparticles were prepared via a sol-gel method by heating the mixture of hydrous SnO2 nanoparticles and SiO2 nanospheres at 600 °C. The average particle size of the obtained SnO2 nanoparticles is 3.3 nm, smaller than that of the SnO2 nanoparticles (~ 6.4 nm) prepared by calcining the pure hydrous SnO2 at 600 °C. The SiO2 nanospheres play an important role in restricting SnO2 nanocrystal growth. The ~3.3 nm-sized SnO2 nanoparticles exhibited high sensitivity for ethanol as well as quick response and recovery time. The concentration detection limit can be as low as 5 ppm at room temperature.

scholarly journals Semiconductor Sensor With Loaded SnO2 Nanoparticles For Early Warning Of Indoor Fires

2019 ◽  
Vol Vol. 14, No.1 ◽  
pp. 37-42 ◽  
Author(s):  
Nelly Maksymovyc ◽  
Ludmila Oleksenko ◽  
Georgiy Fedorenko ◽  
Ganna Arinarkhova ◽  
Keyword(s):  
Early Warning ◽  
Tin Dioxide ◽  
Sno2 Nanoparticles ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Sensitivity ◽  
Average Particle ◽  
Sensitive Layer ◽  
Semiconductor Sensor ◽  
Wide Range

Nanosized tin dioxide material with an average particle size of 10-11 nm was prepared by a sol-gel method. The material has been tested as a gas sensitive layer of a semiconductor sensor. Platinum was introduced into the gas sensitive layer to increase the sensor response to hydrogen. It was shown that the Pt-containing sensor has high sensitivity to hydrogen: its electrical resistance changes in 9.2 times in the presence of 22 ppm H2 in air. It was demonstrated that the sensor applicable to a wide range of H2 measurements in air (3-935 ppm) and has a fast dynamic response. The sensor demonstrates rather good reproducibility of its signal to H2 and withstands hydrogen overload (935 ppm) without a loss of its sensitivity to H2 microconcentration (22 ppm). The results are prospective for applying the sensor in the detectors for early warning of indoor fires.

scholarly journals Adsorption-Semiconductor Sensor Based on Nanosized SnO2 for Early Warning of Indoor Fires

2021 ◽  
Author(s):  
Nelli Maksymovych ◽  
Ludmila Oleksenko ◽  
George Fedorenko
Keyword(s):  
Tin Dioxide ◽  
Early Stage ◽  
Dynamic Properties ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Sensitivity ◽  
Average Particle ◽  
Semiconductor Sensor ◽  
Wide Range

The paper is devoted for a solution of indoors fires prevention at early stage by determination of H2 (fire precursor gas) in air using a semiconductor sensor. A material based on Pt-containing nanosized tin dioxide with an average particle size of 10–11 nm obtained via a sol–gel method was created for a gas sensitive layer of the sensor. The developed sensor has high sensitivity to H2 micro concentration, a wide range of its detectable content in air, selectivity of H2 measuring in the presence of СО and СН4, good dynamic properties. The combination of these properties is very important for prevention of inflammations on their early stages before the open fires appearance. Economic benefit of the proposed sensor is due to a lower cost and higher reliability of the fire situation detection.

scholarly journals An Ultrahigh Sensitivity Acetone Sensor Enhanced by Light Illumination

Sensors ◽  
2018 ◽  
Vol 18 (7) ◽  
pp. 2318 ◽  
Author(s):  
Heng Zhang ◽  
Hongwei Qin ◽  
Chengyong Gao ◽  
Jifan Hu
Keyword(s):  
Operating Temperature ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Sensitivity ◽  
Optimum Operating ◽  
Average Particle ◽  
Light Illumination ◽  
Acetone Vapor ◽  
Optimum Operating Temperature ◽  
Ultrahigh Sensitivity

Au:SmFe0.9Zn0.1O3 is synthesized by a sol-gel method and annealed at 750 °C. Through XRD, SEM and XPS analysis methods, the microstructure of the material has been observed. The average particle size is about 50 nm. The sensor shows a high sensitivity toward acetone vapor. As the relative humidity increases, the resistance and sensitivity of the sensor decline. To obtain a low optimum operating temperature, light illumination with different wavelengths has been introduced. The sensitivity toward acetone is improved at lower operating temperature when the sensor is irradiated by light. The smaller the wavelengths, the better the sensitivity of the sensor. Compared with other gases, the sensor shows excellent selectivity to acetone vapor, with better sensitivity, selectivity and stability when under light illumination.

Synthesis of Cu Loaded TiO2 Nanoparticles for the Improved Photocatalytic Degradation of Rhodamine B

2016 ◽  
Vol 15 (05n06) ◽  
pp. 1660002 ◽  
Author(s):  
V. Kavitha ◽  
P. S. Ramesh ◽  
D. Geetha
Keyword(s):  
Titanium Dioxide ◽  
Rhodamine B ◽  
Sol Gel ◽  
Average Particle Size ◽  
Visible Spectrum ◽  
Xrd Analysis ◽  
Bandgap Energy ◽  
Average Particle ◽  
Titanium Tetraisopropoxide ◽  
Photoexcited Electron

Copper doped Titanium dioxide TiO2 nanoparticles were synthesized by sol–gel method using titanium tetraisopropoxide and copper sulfate as precursors. The synthesized nanoparticles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), UV-Visible spectroscopy (UV-Vis), Photoluminesce spectroscopy (PL) and atomic force microscopy (AFM). XRD analysis confirms the formation of anatase titanium dioxide and average particle size was 35[Formula: see text]nm. Cu– TiO2 exhibits a shift in the absorption edge toward visible spectrum. The rate of recombination and transfer behavior of the photoexcited electron–hole pairs in the semiconductors was recorded by photoluminescence. From SEM spherical shaped nanoparticles was observed. Comparing with pure TiO2 nanoparticles, Cu doped TiO2 photocatalyst exhibited enhanced photocatalytic activity under natural sunlight irradiation in the decomposition of rhodamine B aqueous solution. The maximum 97% of degradation efficiency of Rhodamine B was observed at 0.6% Cu–TiO2 within 180[Formula: see text]min. The photocatalytic efficiency of Rhodamine B of Cu doped TiO2 nanoparticle was higher than the pure TiO2, which could be attributed to the small crystallinity intense light absorption in Sunlight and narrow bandgap energy of Copper.

Nanocrystalline α-Fe2O3: A Superparamagnetic Material for w-LED Application and Waste Water Treatment

2021 ◽  
Author(s):  
Mahesh Gaidhane ◽  
Deepak Taikar ◽  
Pravin Gaidhane ◽  
Kalpana Nagde
Keyword(s):  
Photocatalytic Activity ◽  
Waste Water Treatment ◽  
Sol Gel ◽  
Average Particle Size ◽  
Emission Spectra ◽  
Broad Emission Band ◽  
Average Particle ◽  
X Ray ◽  
Prepared Material ◽  
Cie Chromaticity

Abstract Nanocrystalline α-Fe2O3 is synthesized by sol-gel technique. The prepared nanomaterial was characterized by X-ray diffraction (XRD), SEM, TEM, Fourier Transform Infrared (FTIR) spectroscopy, Vibrating Sample Magnetometry (VSM) and photoluminescence (PL) techniques. X-ray powder diffraction analysis confirmed the formation of α-Fe2O3. Electron microscopy showed spherical morphologies with an average particle size of 30-40 nm. The magnetic property of the prepared material was studied by VSM at room temperature. VSM study shows superparamagnetic nature of the synthesized nanoparticles. Photoluminescence (PL) emission spectra show intense broad emission band centered at 570 nm with 393 nm excitation indicating its usefulness for w-LED application. The CIE-chromaticity color coordinates of prepared material were calculated. The photocatalytic activity of the α-Fe2O3 nanoparticles was analyzed and the nanopowder exhibited good photocatalytic activity for the removal AO7 from its aqueous solution.

Preparation of Magnesium-Based Cobalt-Ferrites (Co1−xMgxFe2O4) Nanoparticles by Sol–Gel Auto Combustion Method

2017 ◽  
Vol 17 (01n02) ◽  
pp. 1760012
Author(s):  
S. Gowreesan ◽  
A. Ruban Kumar
Keyword(s):  
Particle Size ◽  
Structural Parameters ◽  
Sol Gel ◽  
Average Particle Size ◽  
Combustion Method ◽  
Dielectric Behavior ◽  
Powder Xrd ◽  
Average Particle ◽  
Cobalt Ferrites ◽  
Auto Combustion

The scope of the present work is in enhancing the particle size, and dielectric properties of Mg-substituted Cobalt ferrites nanoparticles prepared by sol–gel auto combustion method. The different ratios of Mg-substituted Co Ferrites (Co[Formula: see text]MgxFe2O4([Formula: see text], 0.05, 0.10, 0.15, 0.20 and 0.30)) are calcinated at 850[Formula: see text]C. The synthesized nanoparticles were characterized by powder XRD, FTIR, FE-SEM, EDX techniques and dielectric behavior. The structural parameters were confirmed from powder XRD and the average particle size is obtained from 39 to 67 nm due to the substitution of Mg[Formula: see text] which was calculated by Debye Scherrer’s formula. FE-SEM showed the surface morphology of the different ratio of the sample. The dielectric loss has measured the frequency range of 50[Formula: see text]Hz–5[Formula: see text]MHz. From electrical modulus, conductivity relaxation and thermal activation of charge carriers has been discussed.

Fabrication and Microstructure of ZnO-TiO2 Composite Membranes by a Reverse Micelle and Sol-Gel Processing

2006 ◽  
Vol 510-511 ◽  
pp. 786-789 ◽  
Author(s):  
Dong Sik Bae ◽  
Byung Ik Kim ◽  
Kyong Sop Han
Keyword(s):  
Particle Size ◽  
Reverse Micelle ◽  
Porous Alumina ◽  
Sol Gel ◽  
Average Particle Size ◽  
Composite Membranes ◽  
Dip Coating ◽  
Narrow Particle Size Distribution ◽  
Average Particle ◽  
Alumina Support

ZnO-TiO2 nanoparticles were synthesized by a reverse micelle and sol-gel process. The average particle size of the colloid was below 30 nm and well dispersed in the solution. ZnOTiO2 composite membranes were fabricated by using the dip-coating method on a porous alumina support. ZnO-TiO2 composite membranes showed a crack-free microstructure and narrow particle size distribution even after the heat treatment up to 600°C. The average particle size of the membrane was 30-40nm, and the pore size of ZnO-TiO2 composite membrane was below 10 nm.

Photocatalytically Active Cotton Fabrics Produced with Anatase Synthesized Using a Low-Temperature Sol-Gel Process

2018 ◽  
Vol 762 ◽  
pp. 408-412
Author(s):  
Raivis Eglītis ◽  
Gundars Mežinskis
Keyword(s):  
Photocatalytic Activity ◽  
Uv Light ◽  
Sol Gel ◽  
Average Particle Size ◽  
Synthesis Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Sol Gel Process ◽  
Anatase Nanoparticles ◽  
Pre Treatment

In this work two different hydrosols were used to impregnate a commercially available cotton fabric with anatase nanoparticles to give it photocatalytic activity. To increase the activity, different pre-treatment methods were applied. The nanoparticle size was determined using dynamic light scattering and x-ray diffraction and the fabrics were examined using scanning electron microscopy. Photocatalytic activity was measured using the degradation of methyl-orange while irradiating the samples with UV light. The synthesis method allowed to produce anatase with an average particle size of 32 to 37 nm depending on the synthesis method used.

scholarly journals Oxide Nanomaterials Based on SnO2 for Semiconductor Hydrogen Sensors

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
George Fedorenko ◽  
Ludmila Oleksenko ◽  
Nelly Maksymovych
Keyword(s):  
Tin Dioxide ◽  
Sol Gel ◽  
Average Particle Size ◽  
Fast Response ◽  
Average Particle ◽  
Hydrogen Sensors ◽  
Measuring Range ◽  
X Ray ◽  
Response And Recovery ◽  
Good Repeatability

Nanosized tin dioxide with an average particle size of 5.3 nm was synthesized by a sol-gel method and characterized by IR spectroscopy, TEM, X-ray, and electron diffraction. The obtained SnO2 can be used as initial material for creation of gas-sensitive layers of adsorption semiconductor sensors. Addition of palladium into the initial nanomaterial allows to improve response to hydrogen of such sensors in comparison with sensors based on undoped SnO2 and provides fast response and recovery time, a wide measuring range of hydrogen content in air ambient, and good repeatability of the sensor signal. Such promising properties could make useful the sensors based on these nanomaterials for devices intended to determine hydrogen in air.

Facile Synthesis and Characterization of Fe-Co Nanoparticles Supported Silica Rice Husk

2016 ◽  
Vol 709 ◽  
pp. 66-69
Author(s):  
Jeyashelly Andas ◽  
Rahmah Atikah Rosdi ◽  
Nur Izzati Mohd Anuar
Keyword(s):  
Particle Size ◽  
Rice Husk ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
Silica Source ◽  
Transmission Electron ◽  
Particle Size Analyzer ◽  
Bimetallic Materials ◽  
Co Nanoparticles

A series of Fe-Co nanoparticles were synthesized via sol-gel route at acidic, neutral and basic condition using rice husk as the silica source. The synthesized nanomaterials were designated as Fe-Co3, Fe-Co7 and Fe-Co9 and characterized by Fourier Transform Infrared (FTIR), Transmission Electron Microscope (TEM) and particle size analyzer. The great effect of pH was clearly evidenced from the shifting in the siloxane bond in the FTIR spectrum. TEM investigation confirmed the existence of discrete and almost sphere like nanoparticles. The particle size decreased with an increase in the pH, registering the smallest average particle size at pH 9. In brief, this study promises a fast, rapid and promising method for the conversion of silica rice husk into nanoscale bimetallic materials.

Sign in / Sign up

Export Citation Format

Share Document