Research on In Situ Anionic Polymerization of PA6/PI Alloy

2011 ◽  
Vol 295-297 ◽  
pp. 21-25
Author(s):  
Hong Kai Zhao ◽  
Li Guang Xiao ◽  
Hong Jie Wang
Keyword(s):  
Molecular Weight ◽  
Bisphenol A ◽  
High Performance ◽  
Hot Spot ◽  
Microscopic Analysis ◽  
Infrared Analysis ◽  
Elongation At Break ◽  
System Temperature ◽  
Lamellar Crystals

High performance trend of plastics has become a hot spot of current research. Select bisphenol A dianhydride and bisphenol A diamine with excellent water resistance as the reactant monomers to obtain anhydride-terminated polyimide with very high molecular weight by two-step polymerization, graft the active radicals of acyl caprolactam using the activity of anhydride and obtain PI modified nylon resin by polymerization.When the system temperature is above 160 °C and the added modifiers are greater than 10%, the system viscosity increases very fast; when the system temperature reaches 140 °C and the added modifiers are at 5%, the system viscosity increases very slowly. It is proved that the reaction in each above step is successful through infrared analysis. The mechanical properties of modified PI nylon increases with the increase of consumption and molecular weight of polyimide, when the molecular weight is selected to be about 8000~10000 and the adding amount is 10wt%~15 wt%, the tensile strength reaches over 85MPa, the notch impact strength is increased to 19.6kJ.m-2 and the elongation at break reaches 18%, which are remarkably better than general engineering plastics.Through microscopic analysis, the molecules of polyimide does not enter crystallization phase of nylon resin, but forms compact lamellar crystals existing in nylon matrix.

Preparation and Performance Research of Polyimide Modified Nylon Resin

2011 ◽  
Vol 236-238 ◽  
pp. 548-551
Author(s):  
Hong Kai Zhao ◽  
Li Guang Xiao ◽  
Xiao Jing Zhang
Keyword(s):  
Bisphenol A ◽  
High Performance ◽  
Water Resistance ◽  
Hot Spot ◽  
Microscopic Analysis ◽  
Infrared Analysis ◽  
Lamellar Crystals ◽  
And Performance ◽  
Performance Research ◽  
Very High

High performance trend of plastics has become a hot spot of current research. Select bisphenol A dianhydride and bisphenol A diamine with excellent water resistance as the reactant monomers to obtain anhydride-terminated polyimide with very high molecular weight by two-step polymerization, graft the active radicals of acyl caprolactam using the activity of anhydride and obtain PI modified nylon resin by polymerization. It is proved that the reaction in each above step is successful through infrared analysis. Through microscopic analysis, the molecules of polyimide does not enter crystallization phase of nylon resin, but forms compact lamellar crystals existing in nylon matrix.

Research on Performance of Polyimide In Situ Modification Anionic Polymerization Nylon 6

2014 ◽  
Vol 1052 ◽  
pp. 242-248
Author(s):  
Hong Kai Zhao ◽  
Hong Li Wang
Keyword(s):  
Bisphenol A ◽  
Water Absorption ◽  
In Situ Polymerization ◽  
Microscopic Analysis ◽  
Nylon 6 ◽  
Grafting Reaction ◽  
Lamellar Crystals ◽  
End Capping ◽  
Short Time

Through the polymerization and grafting reaction of bisphenol A dianhydride and bisphenol A diamine, the polyimide activator (PI activator) of acyl caprolactam end capping is obtained and then the anionic in-situ polymerization modified nylon 6 resin is obtained. Viscosity analysis shows that PI consumption is higher than 0.1 (of monomer mass), the reaction temperature is higher than 160°C, the viscosity rises rapidly in a short time and the rapid polymerization molding can be realized; when PI consumption is higher than 0.15 (of monomer mass), the water absorption of matrix resin will be lower than 1.4%; compared with the nylon resin, its water absorption is significantly lowered and its mechanical property is improved greatly; microscopic analysis shows that PI molecules fail to enter the crystalline phase of the nylon 6 and form lamellar crystals in the nylon matrix, which plays a role of enhancement and obstruction; differential thermal analysis shows that PI reduces the melting enthalpy and melting point temperature of nylon 6 resin, which indicates that PI reduces the crystallization capacity of nylon 6.

scholarly journals In Situ Formation of Ionic Liquid by Metathesis Reaction for the Rapid Removal of Bisphenol A from Aqueous Solutions

Water ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 2087 ◽  
Author(s):  
Yesica Vicente-Martínez ◽  
Manuel Caravaca ◽  
Antonio Soto-Meca ◽  
Óscar De Francisco-Ortíz ◽  
Carmen Fernández-López
Keyword(s):  
Ionic Liquid ◽  
Bisphenol A ◽  
Aqueous Solutions ◽  
High Performance ◽  
Cost Effective ◽  
Metathesis Reaction ◽  
Experimental Conditions ◽  
Easy Method ◽  
Dispersive Liquid Liquid Microextraction

In this work we present a rapid and easy method to remove the totality of bisphenol A from aqueous solutions using ionic liquid (IL). Dispersive liquid–liquid microextraction is employed. The IL 1-octyl-3-methylimidazolium bis((trifluoromethane)sulfonyl)imide ([C8C1im] [NTf2]) is formed in situ because of the mixture of 1-octyl-3-methylimidazolium chloride ([C8C1im]Cl) and lithium bis(trifluoromethanesulfonyl)imide (Li[NTf2]) aqueous solutions. A cloud of microdroplets of IL formed by the dispersion generated through the precursors metathesis reaction allows the rapid and total extraction of bisphenol A (BPA). After centrifugation, the formed IL phase is deposited at the bottom of the flask and the total amount of BPA is extracted in the sedimented phase. The volume of IL is very low, in the order of microliters, which enables us to remove all the BPA from the solution. The technique studied is highly efficient, cost-effective, and presents less environmental impact than other extraction techniques, thus becoming an outstanding alternative to the most commonly used methods. BPA concentration is determined by high performance liquid chromatography by injecting the IL phase directly. An extraction kinetic model for the kinetic profile has been tested for this method, which allows to infer the ideal experimental conditions to execute the extraction method.

scholarly journals Multi-Scale Digital Image Correlation Analysis of In Situ Deformation of Open-Cell Porous Ultra-High Molecular Weight Polyethylene Foam

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2607
Author(s):  
Eugene S. Statnik ◽  
Codrutza Dragu ◽  
Cyril Besnard ◽  
Alexander J.G. Lunt ◽  
Alexey I. Salimon ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Digital Image Correlation ◽  
High Molecular Weight ◽  
Digital Image ◽  
High Performance ◽  
Image Correlation ◽  
Deformation Bands ◽  
Open Cell ◽  
Ultra High Molecular Weight

Porous ultra-high molecular weight polyethylene (UHMWPE) is a high-performance bioinert polymer used in cranio-facial reconstructive surgery in procedures where relatively low mechanical stresses arise. As an alternative to much stiffer and more costly polyether-ether-ketone (PEEK) polymer, UHMWPE is finding further wide applications in hierarchically structured hybrids for advanced implants mimicking cartilage, cortical and trabecular bone tissues within a single component. The mechanical behaviour of open-cell UHMWPE sponges obtained through sacrificial desalination of hot compression-moulded UHMWPE-NaCl powder mixtures shows a complex dependence on the fabrication parameters and microstructural features. In particular, similarly to other porous media, it displays significant inhomogeneity of strain that readily localises within deformation bands that govern the overall response. In this article, we report advances in the development of accurate experimental techniques for operando studies of the structure–performance relationship applied to the porous UHMWPE medium with pore sizes of about 250 µm that are most well-suited for live cell proliferation and fast vascularization of implants. Samples of UHMWPE sponges were subjected to in situ compression using a micromechanical testing device within Scanning Electron Microscope (SEM) chamber, allowing the acquisition of high-resolution image sequences for Digital Image Correlation (DIC) analysis. Special masking and image processing algorithms were developed and applied to reveal the evolution of pore size and aspect ratio. Key structural evolution and deformation localisation phenomena were identified at both macro- and micro-structural levels in the elastic and plastic regimes. The motion of pore walls was quantitatively described, and the presence and influence of strain localisation zones were revealed and analysed using DIC technique.

Melting Behaviors of Lamellar Crystals of Poly(bisphenol A-co-decane ether) Studied by in-Situ Atomic Force Microscopy

Langmuir ◽  
2003 ◽  
Vol 19 (19) ◽  
pp. 8010-8018 ◽  
Author(s):  
Yong Jiang ◽  
Xi-Gao Jin ◽  
Charles C. Han ◽  
Lin Li ◽  
Yong Wang ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Bisphenol A ◽  
Force Microscopy ◽  
Atomic Force ◽  
Lamellar Crystals

A high-performance oil-free backing pump for electron microscopes

1978 ◽  
Vol 36 (1) ◽  
pp. 110-111
Author(s):  
G.K.W. Balkau ◽  
E. Bez ◽  
J.L. Farrant
Keyword(s):  
Molecular Weight ◽  
Electron Microscope ◽  
Hot Spots ◽  
High Performance ◽  
Carbonaceous Material ◽  
Contamination Rate ◽  
Low Molecular Weight ◽  
Principal Source ◽  
Rotary Pumps ◽  
Electron Microscopes

The earliest account of the contamination of electron microscope specimens by the deposition of carbonaceous material during electron irradiation was published in 1947 by Watson who was then working in Canada. It was soon established that this carbonaceous material is formed from organic vapours, and it is now recognized that the principal source is the oil-sealed rotary pumps which provide the backing vacuum. It has been shown that the organic vapours consist of low molecular weight fragments of oil molecules which have been degraded at hot spots produced by friction between the vanes and the surfaces on which they slide. As satisfactory oil-free pumps are unavailable, it is standard electron microscope practice to reduce the partial pressure of organic vapours in the microscope in the vicinity of the specimen by using liquid-nitrogen cooled anti-contamination devices. Traps of this type are sufficient to reduce the contamination rate to about 0.1 Å per min, which is tolerable for many investigations.

Molecular and Microscopic Analysis of Altered Gene Expression in Transgenic and Gene Targeted Mice

1996 ◽  
Vol 54 ◽  
pp. 12-13
Author(s):  
W. K. Jones ◽  
J. Robbins
Keyword(s):  
Gene Expression ◽  
Pulmonary Veins ◽  
Microscopic Analysis ◽  
Mouse Tissue ◽  
Adult Heart ◽  
Heavy Chains ◽  
Altered Gene Expression ◽  
Altered Gene ◽  
Pulmonary Myocardium

Two myosin heavy chains (MyHC) are expressed in the mammalian heart and are differentially regulated during development. In the mouse, the α-MyHC is expressed constitutively in the atrium. At birth, the β-MyHC is downregulated and replaced by the α-MyHC, which is the sole cardiac MyHC isoform in the adult heart. We have employed transgenic and gene-targeting methodologies to study the regulation of cardiac MyHC gene expression and the functional and developmental consequences of altered α-MyHC expression in the mouse.We previously characterized an α-MyHC promoter capable of driving tissue-specific and developmentally correct expression of a CAT (chloramphenicol acetyltransferase) marker in the mouse. Tissue surveys detected a small amount of CAT activity in the lung (Fig. 1a). The results of in situ hybridization analyses indicated that the pattern of CAT transcript in the adult heart (Fig. 1b, top panel) is the same as that of α-MyHC (Fig. 1b, lower panel). The α-MyHC gene is expressed in a layer of cardiac muscle (pulmonary myocardium) associated with the pulmonary veins (Fig. 1c). These studies extend our understanding of α-MyHC expression and delimit a third cardiac compartment.

High performance Nanogold™-in situ hybridzation and its use in the detection of hybridized and PCR-amplified microscopical preparations

1996 ◽  
Vol 54 ◽  
pp. 896-897
Author(s):  
G. W. Hacker ◽  
I. Zehbe ◽  
J. Hainfeld ◽  
A.-H. Graf ◽  
C. Hauser-Kronberger ◽  
...  
Keyword(s):  
Polymerase Chain Reaction ◽  
Messenger Rna ◽  
High Performance ◽  
Detection System ◽  
Direct Methods ◽  
Genetic Alterations ◽  
Chain Reaction ◽  
Protein Encoding ◽  
Polymerase Chain

In situ hybridization (ISH) with biotin-labeled probes is increasingly used in histology, histopathology and molecular biology, to detect genetic nucleic acid sequences of interest, such as viruses, genetic alterations and peptide-/protein-encoding messenger RNA (mRNA). In situ polymerase chain reaction (PCR) (PCR in situ hybridization = PISH) and the new in situ self-sustained sequence replication-based amplification (3SR) method even allow the detection of single copies of DNA or RNA in cytological and histological material. However, there is a number of considerable problems with the in situ PCR methods available today: False positives due to mis-priming of DNA breakdown products contained in several types of cells causing non-specific incorporation of label in direct methods, and re-diffusion artefacts of amplicons into previously negative cells have been observed. To avoid these problems, super-sensitive ISH procedures can be used, and it is well known that the sensitivity and outcome of these methods partially depend on the detection system used.

Sign in / Sign up

Export Citation Format

Share Document