Analysis of Vapor Evaporation Loss in Filling Gasoline into Tank

2011 ◽  
Vol 347-353 ◽  
pp. 372-375 ◽  
Author(s):  
Wei Qiu Huang ◽  
Feng Li ◽  
Shu Hua Zhao ◽  
Jing Zhong
Keyword(s):  
Mass Transfer ◽  
Experimental System ◽  
Pilot Scale ◽  
Convective Transport ◽  
Operating Conditions ◽  
Vapor Concentration ◽  
Air Mass ◽  
Evaporation Loss ◽  
Gas Space ◽  
Gasoline Evaporation

A pilot-scale experimental system of filling gasoline into a tank was built to investigate gasoline vapor-air mass transfer in the tank gas space and the vapor evaporation loss from the tank in different operating conditions. The results showed that the higher the location of filling pipe exit inside the tank, the quicker the speed of the filling gasoline, and the higher the initial vapor concentration in the tank gas space, then the more severe the vapor-air convective transport and the larger the gasoline evaporation loss rates.

scholarly journals Development and evaluation of silicone membrane as aerators for membrane bioreactors

2005 ◽  
Author(s):  
◽  
Xolani Proffessor Mbulawa
Keyword(s):  
Mass Transfer ◽  
Experimental Study ◽  
Dissolved Oxygen ◽  
Oxygen Concentration ◽  
Silicone Rubber ◽  
Convective Transport ◽  
Operating Conditions ◽  
Pure Oxygen ◽  
Bulk Liquid ◽  
Dissolved Oxygen Concentration

In bubble-less aeration oxygen diffuses through the membrane in a molecular form and dissolves in the liquid. Oxygen is fed through the lumen side of silicone rubber tube. On the outer surface of the membrane there is a boundary layer that is created by oxygen. This then gets transported to the bulk liquid by convective transport created by water circulation through the pump. The driving force of the convective transport is due to concentration difference between the dissolved oxygen in water and oxygen saturation concentration in water at a particular temperature and pressure. The design of a membrane aerated bioreactor needs an understanding of the factors that govern oxygen mass transfer. It is necessary to know the effects of operating conditions and design configurations. Although various methods of bubble-less aeration have been reported, there still exists a lack of knowledge on the immersed membrane systems. This study is aiming at contributing to the development of an immersed membrane bioreactor using silicone rubber tubular membrane as means of providing oxygen. The secondary objective was to investigate the influence that the operating conditions and module configuration have on the system behaviour. From the experimental study, the characteristic dissolved oxygen -time curve show that there is a saturation limit equivalent to the equilibrium dissolved oxygen concentration, after which there is no increase in dissolved oxygen with time. At ambient conditions the equilibrium dissolved oxygen is approximately 8 mg/L. This is when water is in contact with air at one atmospheric pressure. At the same conditions the equilibrium dissolved oxygen concentration when water is in contact with pure oxygen is approximately 40 mg/L. This is why all the experiments were conducted from 2mg/L dissolved oxygen concentration in water, to enable enough time to reach equilibrium so as to determine mass transfer coefficient. The most important parameters that were investigated to characterise the reactor were, oxygen supply pressure, crossflow velocity, temperature and module orientation. Observations from the experimental study indicated that when the system is controlled by pressure, crossflow does not have a significant effect on mass transfer. When the system is controlled by the convective transport from the membrane surface to the bulk liquid, pressure does not have a significant effect on mass transfer. All four effects that were investigated in the study are discussed.

scholarly journals Effects of geometric parameters on volumetric mass transfer coefficient of non-Newtonian fluids in stirred tanks

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Haider Ali ◽  
Sofia Zhu ◽  
Jannike Solsvik
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Scale Up ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Volumetric Mass Transfer Coefficient ◽  
Transfer Coefficients ◽  
Stirred Tanks

Abstract Scaling up stirred tanks is a significant challenge because of the research gaps between laboratory and industrial-scale setups. It is necessary to understand the effects of scale-up on the mass transfer in stirred tanks, and this requires meticulous experimental analysis. The present study investigates the effects of tank size and aspect ratio ( H L T ${H}_{L}}{T}$ ) on the volumetric mass transfer coefficients of shear-thinning fluids. The experiments were conducted in three stirred tanks of different sizes (laboratory and pilot scale) and geometries (standard and nonstandard). H L T ${H}_{L}}{T}$ was 1 for the standard tanks and 3.5 for the nonstandard stirred tanks. Three sizes of stirred tanks were used: 11 L with H L T ${H}_{L}}{T}$ of 1, 40 L with H L T ${H}_{L}}{T}$ of 3.5, and 47 L with H L T ${H}_{L}}{T}$ of 1. Impeller stirring speeds and gas flow rates were in the range of 800–900 rev min−1 and 8–10 L min−1, respectively. The volumetric mass transfer coefficient was estimated based on the dissolved oxygen concentration in the fluids, and the effects of rheology and operating conditions on the volumetric mass transfer coefficient were observed. The volumetric mass transfer coefficient decreased as tank size increased and increased with an increase in operating conditions, but these effects were also clearly influenced by fluid rheology. The impacts of scale-up and operating conditions on the volumetric mass transfer coefficient decreased as liquid viscosity increased.

On Entropy Generation and the Effect of Heat and Mass Transfer Coupling in a Distillation Process

2018 ◽  
Vol 43 (1) ◽  
pp. 57-74
Author(s):  
Paulina Burgos-Madrigal ◽  
Diego F. Mendoza ◽  
Mariano López de Haro
Keyword(s):  
Mass Transfer ◽  
Entropy Production ◽  
Heat And Mass Transfer ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Entropy Production Rate ◽  
Distillation Columns ◽  
First Case ◽  
Three Stages ◽  
Cold Liquid

AbstractThe entropy production rates as obtained from the exergy analysis, entropy balance and the nonequilibrium thermodynamics approach are compared for two distillation columns. The first case is a depropanizer column involving a mixture of ethane, propane, n-butane and n-pentane. The other is a weighed sample of Mexican crude oil distilled with a pilot scale fractionating column. The composition, temperature and flow profiles, for a given duty and operating conditions in each column, are obtained with the Aspen Plus V8.4 software by using the RateFrac model with a rate-based nonequilibrium column. For the depropanizer column the highest entropy production rate is found in the central trays where most of the mass transfer occurs, while in the second column the highest values correspond to the first three stages (where the vapor mixture is in contact with the cold liquid reflux), and to the last three stages (where the highest temperatures take place). The importance of the explicit inclusion of thermal diffusion in these processes is evaluated. In the depropanizer column, the effect of the coupling between heat and mass transfer is found to be negligible, while for the fractionating column it becomes appreciable.

Application of a Pilot-Scale Pulsed Electrocoagulation system to OCC-Based Paper Mill Effluent

TAPPI Journal ◽  
2009 ◽  
Vol 8 (3) ◽  
pp. 14-20 ◽  
Author(s):  
YUAN-SHING PERNG ◽  
EUGENE I-CHEN WANG ◽  
SHIH-TSUNG YU ◽  
AN-YI CHANG
Keyword(s):  
Water Quality ◽  
Quality Indicators ◽  
Paper Mill ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Optimal Dosage ◽  
Water Quality Indicators ◽  
Paper Mill Effluent ◽  
Treated Effluent ◽  
True Color

Trends toward closure of white water recirculation loops in papermaking often lead to a need for system modifications. We conducted a pilot-scale study using pulsed electrocoagulation technology to treat the effluent of an old corrugated containerboard (OCC)-based paper mill in order to evaluate its treatment performance. The operating variables were a current density of 0–240 A/m2, a hydraulic retention time (HRT) of 8–16 min, and a coagulant (anionic polyacrylamide) dosage of 0–22 mg/L. Water quality indicators investigated were electrical con-ductivity, suspended solids (SS), chemical oxygen demand (COD), and true color. The results were encouraging. Under the operating conditions without coagulant addition, the highest removals for conductivity, SS, COD, and true color were 39.8%, 85.7%, 70.5%, and 97.1%, respectively (with an HRT of 16 min). The use of a coagulant enhanced the removal of both conductivity and COD. With an optimal dosage of 20 mg/L and a shortened HRT of 10 min, the highest removal achieved for the four water quality indicators were 37.7%, 88.7%, 74.2%, and 91.7%, respectively. The water qualities thus attained should be adequate to allow reuse of a substantial portion of the treated effluent as process water makeup in papermaking.

A pilot web former designed to study retention-formation relationships

2010 ◽  
Vol 25 (2) ◽  
pp. 185-194
Author(s):  
Anna Svedberg ◽  
Tom Lindström
Keyword(s):  
Pilot Scale ◽  
Operating Conditions ◽  
Montmorillonite Clay ◽  
Speed Ratio ◽  
Good Reproducibility ◽  
Total Solids ◽  
Retention Aids ◽  
Solids Content ◽  
Relationship Of ◽  
The Relationship

Abstract A pilot-scale fourdrinier former has been developed for the purpose of investigating the relationship between retention and paper formation (features, retention aids, dosage points, etc.). The main objective of this publication was to present the R-F (Retention and formation)-machine and demonstrate some of its fields of applications. For a fine paper stock (90% hardwood and 10% softwood) with addition of 25% filler (based on total solids content), the relationship between retention and formation was investigated for a microparticulate retention aid (cationic polyacrylamide together with anionic montmorillonite clay). The retention-formation relationship of the retention aid system was investigated after choosing standardized machine operating conditions (e.g. the jet-to-wire speed ratio). As expected, the formation was impaired when the retention was increased. Since good reproducibility was attained, the R-F (Retention and formation)-machine was found to be a useful tool for studying the relationship between retention and paper formation.

Nanofiltration of colored surface water: Quebec's experience

2003 ◽  
Vol 3 (5-6) ◽  
pp. 15-22
Author(s):  
P. Kouadio ◽  
M. Tétrault
Keyword(s):  
Drinking Water ◽  
Surface Water ◽  
Membrane Fouling ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Quebec City ◽  
Water Regulation ◽  
Eastern Canada

Three colored surface water nanofiltration pilot-scale projects were conducted in the province of Quebec (eastern Canada), between November 2000 and March 2002, by the company H2O Innovation (2000) inc., for the municipalities of Lac Bouchette, Latulipe-et-Gaboury and Charlesbourg (now part of Quebec City). Results indicated that nanofiltration permeate quality has an advance on present drinking water regulation standard in Quebec, but important membrane fouling occurred. Fouling can be controlled by pretreatment and optimization of the operating conditions.

scholarly journals Simulation of a Downdraft Gasifier for Production of Syngas from Different Biomass Feedstocks

2021 ◽  
Vol 5 (2) ◽  
pp. 20
Author(s):  
Mateus Paiva ◽  
Admilson Vieira ◽  
Helder T. Gomes ◽  
Paulo Brito
Keyword(s):  
Modeling And Simulation ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Fuel Gas ◽  
Heating Value ◽  
Downdraft Gasifier ◽  
Process Operation ◽  
Independent Parameters ◽  
Gasification Temperature ◽  
Main Operating

In the evaluation of gasification processes, estimating the composition of the fuel gas for different conditions is fundamental to identify the best operating conditions. In this way, modeling and simulation of gasification provide an analysis of the process performance, allowing for resource and time savings in pilot-scale process operation, as it predicts the behavior and analyzes the effects of different variables on the process. Thus, the focus of this work was the modeling and simulation of biomass gasification processes using the UniSim Design chemical process software, in order to satisfactorily reproduce the operation behavior of a downdraft gasifier. The study was performed for two residual biomasses (forest and agricultural) in order to predict the produced syngas composition. The reactors simulated gasification by minimizing the free energy of Gibbs. The main operating parameters considered were the equivalence ratio (ER), steam to biomass ratio (SBR), and gasification temperature (independent variables). In the simulations, a sensitivity analysis was carried out, where the effects of these parameters on the composition of syngas, flow of syngas, and heating value (dependent variables) were studied, in order to maximize these three variables in the process with the choice of the best parameters of operation. The model is able to predict the performance of the gasifier and it is qualified to analyze the behavior of the independent parameters in the gasification results. With a temperature between 850 and 950 °C, SBR up to 0.2, and ER between 0.3 and 0.5, the best operating conditions are obtained for maximizing the composition of the syngas in CO and H2.

Numerical Analysis of the Heat and Mass Transfer Characteristics in an Autothermal Methane Reformer

2010 ◽  
Vol 7 (5) ◽  
Author(s):  
Joonguen Park ◽  
Shinku Lee ◽  
Sunyoung Kim ◽  
Joongmyeon Bae
Keyword(s):  
Mass Transfer ◽  
Numerical Analysis ◽  
Heat And Mass Transfer ◽  
Steam Reforming ◽  
Space Velocity ◽  
Reaction Model ◽  
Operating Conditions ◽  
Local Thermal Equilibrium ◽  
Inlet Temperature ◽  
Transfer Characteristics

This paper discusses a numerical analysis of the heat and mass transfer characteristics in an autothermal methane reformer. Assuming local thermal equilibrium between the bulk gas and the surface of the catalyst, a one-medium approach for the porous medium analysis was incorporated. Also, the mass transfer between the bulk gas and the catalyst’s surface was neglected due to the relatively low gas velocity. For the catalytic surface reaction, the Langmuir–Hinshelwood model was incorporated in which methane (CH4) is reformed to hydrogen-rich gases by the autothermal reforming (ATR) reaction. Full combustion, steam reforming, water-gas shift, and direct steam reforming reactions were included in the chemical reaction model. Mass, momentum, energy, and species balance equations were simultaneously calculated with the chemical reactions for the multiphysics analysis. By varying the four operating conditions (inlet temperature, oxygen to carbon ratio (OCR), steam to carbon ratio, and gas hourly space velocity (GHSV)), the performance of the ATR reactor was estimated by the numerical calculations. The SR reaction rate was improved by an increased inlet temperature. The reforming efficiency and the fuel conversion reached their maximum values at an OCR of 0.7. When the GHSV was increased, the reforming efficiency increased but the large pressure drop may decrease the system efficiency. From these results, we can estimate the optimal operating conditions for the production of large amounts of hydrogen from methane.

Sign in / Sign up

Export Citation Format

Share Document