Study on Three-Point Bending Numerical Tests of CFRP Reinforced Concrete Beam with Initial Crack

2013 ◽  
Vol 838-841 ◽  
pp. 639-643
Author(s):  
Xing Quan Li ◽  
Xiao Yan Sun ◽  
Ya Wei Li
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Reinforced Concrete Beam ◽  
Initial Crack ◽  
Propagation Path ◽  
Three Point Bending ◽  
Numerical Tests

Based on extended finite element method (XFEM) of the finite element software platform-ABAQUS, three-point bending numerical simulation of CFRP reinforced concrete beam with initial crack has been made to predict the 3D crack propagation path. The numerical tests present the crack propagation path under ultimate load and crack damage modes of non-CFRP and some different CFRP plies. The results show that the strength of CFRP reinforced concrete beam is obviously improved and the crack which previous penetrate through doesnt penetrate through concrete beam under CFRP reinforce based on multiple optometric numerical simulation results. The results of this paper can also provide some foundations for damage mode, the ultimate load and CFRP overlay design of reinforced concrete beams.

Numerical Simulation on the Form of Reinforcement of Reinforced Concrete Beam with Openings

2013 ◽  
Vol 444-445 ◽  
pp. 884-888
Author(s):  
Xue Han ◽  
Zheng Liu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Failure Mechanism ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Plasticity Model ◽  
Damage Factor ◽  
Finite Element Software ◽  
Concrete Damaged Plasticity

In order to research the stress performance of reinforced concrete beam with different forms of reinforcement around the openings, a numerical simulation on reinforced concrete beam with circle openings is made by using the finite element software. The constitutive relation of concrete offered by the 2010 edition of code for design of concrete structures and the concrete damaged plasticity model is adopted in this article. The damage factor is introduced in the process of modeling, which can reflect the damage of beams with different forms of reinforcement directly and help to reveal the failure mechanism of members. Thus we can propose the optimization of reinforcement method.

Nonlinear Finite Element Analysis of Layered Steel Fiber Reinforced Concrete Beam

2012 ◽  
Vol 166-169 ◽  
pp. 616-619 ◽  
Author(s):  
Hang Jing ◽  
Yong Quan Li
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Steel Fiber ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Element Analysis

A simplified finite element model for analysis of the Layered steel fiber beams with the concrete damaged plasticity model has been presented. The numerical simulation of load-deflection curve of layered steel fiber reinforced concrete beam under three-point loads is performed using ABAQUS. The results of simulation are generally in conformance with the experiment. The results of numerical simulation show that layered steel fiber has little contribution to the elastic capacity of concrete beam. But it can improve the ultimate bearing capacity of concrete beam obviously. The bending collapse style of layered steel fiber reinforced concrete beam is different from plain concrete beam evidently with obvious ductile characteristic.

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

scholarly journals Numerical Derivation of Iso-Damaged Curve for a Reinforced Concrete Beam Subjected to Blast Loading

2018 ◽  
Vol 149 ◽  
pp. 02016 ◽  
Author(s):  
Yehya Temsah ◽  
Ali Jahami ◽  
Jamal Khatib ◽  
M Sonebi
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Shock Waves ◽  
Concrete Beam ◽  
Blast Loading ◽  
Reinforced Concrete Beam ◽  
Structural Elements ◽  
Finite Element Program ◽  
Element Program ◽  
Structural Engineers

Many engineering facilities are severely damaged by blast loading. Therefore, many manufacturers of sensitive, breakable, and deformed structures (such as facades of glass buildings) carry out studies and set standards for these installations to withstand shock waves caused by explosions. Structural engineers also use these standards in their designs for various structural elements by following the ISO Damage Carve, which links pressure and Impulse. As all the points below this curve means that the structure is safe and will not exceed the degree of damage based on the various assumptions made. This research aims to derive the Iso-Damage curve of a reinforced concrete beam exposed to blast wave. An advanced volumetric finite element program (ABAQUS) will be used to perform the derivation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals Numerical Simulation on Reinforced Concrete Beam with Different Cover Size under Two Point Bending Load

2021 ◽  
Vol 7 (05) ◽  
pp. 39-43
Author(s):  
R Padma Rani & R Harshani
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Structural Analysis ◽  
Concrete Beam ◽  
Failure Modes ◽  
Equivalent Stress ◽  
Reinforced Concrete Beam ◽  
Simulation Software ◽  
Beam Specimen ◽  
Bending Load

Structural analysis is used to assess the behavior of engineering structures under the application of loads. Usually, structural analysis methods include analytical,experimental and numerical methods is used in thisproject, however, only Analytical method is used and the values are taken from literature reference, to get familiar with Finite Element Analysis (FEA) using ANSYS, this is done to acquire practical knowledge about of the effect of the cover. The aim is to identify different failure modes under a range of loading conditions by changing the cover size to get the data of various parameters such as deflection, stress etc. Study of cover helps to observe the stability, reliability and the overall strength of the structural beam. This project attempts made to study the effect of cover on the behavior of reinforced concrete beam. Forthis analytical study, the Reinforced concrete beam specimen of 2000x100x200mm was considered.ANSYS software is a suite of engineering simulation software, based on finite element method, which can solve problems ranging from linear analysis to nonlinear analysis. The Doubly reinforced beams weremodeled by using geometry. In this model,various covers are provided. The beam specimensused in this study were tested under two-point static loading condition until failure of the specimen. From theobtained resultconcluded that the total deformation and directional deformation values are low in 25mm cover compared to other cases but the equivalent stress value is low in 35mm cover size compared to 25mm cover size.

Numerical Analysis of Reinforced Concrete Beam Strengthened with CFRP or GFRP Laminates

2016 ◽  
Vol 707 ◽  
pp. 51-59 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Rania Khattab
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

The behaviour of reinforced concrete beam strengthened with Carbon Fiber Reinforced Polymer (CFRP) and Glass fiber reinforced polymer GFRP laminates was investigated using finite element models and the results are presented in this paper. The numerical investigation assessed the effect of the configuration of FRP strengthening laminates on the behaviour of concrete beams. The load-deflection behaviour, and ultimate load of strengthened beam were compared to those of un-strengthened concrete beams. It was shown that using U-shaped FRP sheets increased the ultimate load. The stiffness of the strengthed beam also increased after first yielding of steel reinforcing bars. At was also observed that strengthening beams with FRP laminates to one-fourth of the beam span, modifies the failure of the beam from shear-controlled near the end of the unstrengthened beam, to flexure-controlled near mid-span. CFRP produced better results compared GFRP in terms of the ability to enhance the behavior of strengthenened reinforced concrete beams.

Sign in / Sign up

Export Citation Format

Share Document