Calcined Mg-Fe Layered Double Hydroxide Adsorbent for Acid Red G Dye Removal

2013 ◽  
Vol 864-867 ◽  
pp. 719-726
Author(s):  
Li Qun Sun ◽  
Zhi Quan Ren
Keyword(s):  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Kinetic Studies ◽  
Order Kinetic ◽  
High Adsorption ◽  
Solution Ph ◽  
Equilibrium Data ◽  
High Adsorption Capacity ◽  
Co Precipitation ◽  
Acid Red G

The calcined Mg-Fe LDH adsorbent (CLDH) was fabricated by co-precipitation and calcination processes. The adsorbent was characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy. The adsorbent exhibited high adsorption capacity for the removal of acid red G (ARG) dye. The effects of the adsorbent dose, solution pH, contact time, reaction temperature and initial ARG dye concentrations upon the ARG dye adsorption were investigated in detail. The kinetic studies indicated that the adsorption process was fitted well with the pseudo-second-order kinetic model (R2> 0.99). The equilibrium data were well described by the Freundlich equation. Moreover, after three regeneration cycles, the CLDH still showed high adsorption capacity. The results showed that the CLDH is an efficient adsorbent for the removal of organic pollutants from wastewater.

scholarly journals Effective Poly (Cyclotriphosphazene-Co-4,4′-Sulfonyldiphenol)@rGO Sheets for Tetracycline Adsorption: Fabrication, Characterization, Adsorption Kinetics and Thermodynamics

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1540
Author(s):  
Muhammad Ahmad ◽  
Tehseen Nawaz ◽  
Mohammad Mujahid Alam ◽  
Yasir Abbas ◽  
Shafqat Ali ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
High Adsorption ◽  
Clean Environment ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
High Adsorption Capacity ◽  
Adsorption Equilibrium Data

The development of excellent drug adsorbents and clarifying the interaction mechanisms between adsorbents and adsorbates are greatly desired for a clean environment. Herein, we report that a reduced graphene oxide modified sheeted polyphosphazene (rGO/poly (cyclotriphosphazene-co-4,4′-sulfonyldiphenol)) defined as PZS on rGO was used to remove the tetracycline (TC) drug from an aqueous solution. Compared to PZS microspheres, the adsorption capacity of sheeted PZS@rGO exhibited a high adsorption capacity of 496 mg/g. The adsorption equilibrium data well obeyed the Langmuir isotherm model, and the kinetics isotherm was fitted to the pseudo-second-order model. Thermodynamic analysis showed that the adsorption of TC was an exothermic, spontaneous process. Furthermore, we highlighted the importance of the surface modification of PZS by the introduction of rGO, which tremendously increased the surface area necessary for high adsorption. Along with high surface area, electrostatic attractions, H-bonding, π-π stacking and Lewis acid-base interactions were involved in the high adsorption capacity of PZS@rGO. Furthermore, we also proposed the mechanism of TC adsorption via PZS@rGO.

scholarly journals Study on the adsorption of methylene blue from aqueous solution using hydrogel glucomannan/graphene oxide

2021 ◽  
Vol 10 (1) ◽  
pp. 59-66
Author(s):  
Son Le Lam ◽  
Phu Nguyen Vinh ◽  
Hieu Le Trung ◽  
Tan Le Thua ◽  
Nhan Dang Thi Thanh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Dye Adsorption ◽  
Order Kinetic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Glucomannan/graphene oxide (GM/GO) hydrogel was synthesized by using calcium hydroxide as the crosslinker. The synthesized material was characterized by using IR, XRD, SEM, EDX and RAMAN technology. The composite hydrogel was used for removal of organic dyes from aqueous solution. The results showed that the GM/GO hydrogel had a porous structure and a high adsorption capacity toward methylene blue (MB). The pseudo-second-order kinetic model could fit the rate equation of MB adsorption onto the GM/GO hydrogel. The adsorption of MB onto GM/GO hydrogel was a spontaneous process. In addition, the equilibrium adsorption isotherm data indicated that equilibrium data were fitted to the Langmuir isotherm and the maximum dye adsorption capacity was 198,69 mg.g-1. Moreover, the hydrogel was stable and easily recovered and adsorption capacity was around 97% of the initial saturation adsorption capacity after being used five times.

Self-assembled three-dimensional graphene-based materials for dye adsorption and catalysis

2015 ◽  
Vol 3 (18) ◽  
pp. 10031-10037 ◽  
Author(s):  
Xueping Zhang ◽  
Dong Liu ◽  
Lu Yang ◽  
Limin Zhou ◽  
Tianyan You
Keyword(s):  
Adsorption Capacity ◽  
Self Assembly ◽  
Three Dimensional ◽  
Dye Adsorption ◽  
Reduction Process ◽  
High Adsorption ◽  
Graphene Aerogel ◽  
High Adsorption Capacity ◽  
Self Assembled

Graphene aerogel (GA) fabricated via a simultaneous self-assembly and reduction process showed high adsorption capacity towards dyes.

scholarly journals Mg-Cr Layered Double Hydroxide Intercalated Oxalic Anion to Remove Cationic Dye Solutions: Rhodamine B and Methylene Blue

2020 ◽  
Vol 9 (2) ◽  
pp. 383-391
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Layered Double Hydroxide ◽  
Rhodamine B ◽  
Physical Adsorption ◽  
Dye Adsorption ◽  
Kinetic Studies ◽  
Economic Feasibility ◽  
Order Kinetic ◽  
Double Hydroxide

A MgCr-based layered double hydroxide (LDH) was synthesized by a coprecipitation method, followed by an intercalation process using an oxalic anion. The materials were characterized using X-ray diffraction analysis, FT-IR spectroscopy, and pH pzc measurement. The materials were then applied as adsorbents for removal of methylene blue (MB) and rhodamine B (RhB) from aqueous solution. Pristine Mg/Cr LDH exhibited RhB adsorption capacity of 32.154 mg g⁻1, whereas the use of intercalated Mg/Cr LDH caused an increase in the capacity (139.526 mg g⁻1). Kinetic studies indicated that the dye adsorption using both LDHs followed a pseudo-second-order kinetic model; the K2 values of pristine and modified Mg/Cr LDH for RhB and MB were 6.970, 0.001, 0.426, and 2.056 g mg⁻1 min⁻1, respectively. The thermodynamic study identified that the adsorption of both dyes onto the LDHs was a spontaneous process and can be classified as physical adsorption with adsorption energies of <40 kJ/mol. Moreover, the desorption and regeneration experiments indicated the high economic feasibility and reusability of the LDHs. By using HCl as the optimal solvent, the LDHs could desorb as much as 98% of the dye and could be used as adsorbents with high adsorption capacity over three cycles.

Parametric and adsorption kinetic studies of methylene blue removal from simulated textile water using durian (Durio zibethinus murray) skin

2015 ◽  
Vol 72 (6) ◽  
pp. 896-907 ◽  
Author(s):  
S. M. Anisuzzaman ◽  
Collin G. Joseph ◽  
D. Krishnaiah ◽  
A. Bono ◽  
L. C. Ooi
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Durio Zibethinus

In this study, durian (Durio zibethinus Murray) skin was examined for its ability to remove methylene blue (MB) dye from simulated textile wastewater. Adsorption equilibrium and kinetics of MB removal from aqueous solutions at different parametric conditions such as different initial concentrations (2–10 mg/L), biosorbent dosages (0.3–0.7 g) and pH solution (4–9) onto durian skin were studied using batch adsorption. The amount of MB adsorbed increased from 3.45 to 17.31 mg/g with the increase in initial concentration of MB dye; whereas biosorbent dosage increased from 1.08 to 2.47 mg/g. Maximum dye adsorption capacity of the durian skin was found to increase from 3.78 to 6.40 mg/g, with increasing solution pH. Equilibrium isotherm data were analyzed according to Langmuir and Freundlich isotherm models. The sorption equilibrium was best described by the Freundlich isotherm model with maximum adsorption capacity of 7.23 mg/g and this was due to the heterogeneous nature of the durian skin surface. Kinetic studies indicated that the sorption of MB dye tended to follow the pseudo second-order kinetic model with promising correlation of 0.9836 &lt; R2 &lt; 0.9918.

scholarly journals Adsorption of Cu(II) by Poly-γ-glutamate/Apatite Nanoparticles

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 962
Author(s):  
Kuo-Yu Chen ◽  
Wei-Yu Zeng
Keyword(s):  
Adsorption Capacity ◽  
Kinetic Studies ◽  
Maximum Adsorption Capacity ◽  
Gravimetric Analysis ◽  
Solution Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Initial Adsorption ◽  
Adsorption Equilibrium Data

Poly-γ-glutamate/apatite (PGA-AP) nanoparticles were prepared by chemical coprecipitation method in the presence of various concentrations of poly-γ-glutamate (γ-PGA). Powder X-ray diffraction pattern and energy-dispersive spectroscopy revealed that the main crystal phase of PGA-AP was hydroxyapatite. The immobilization of γ-PGA on PGA-AP was confirmed by Fourier transform infrared spectroscopy and the relative amount of γ-PGA incorporation into PGA-AP was determined by thermal gravimetric analysis. Dynamic light scattering measurements indicated that the particle size of PGA-AP nanoparticles increased remarkably with the decrease of γ-PGA content. The adsorption of aqueous Cu(II) onto the PGA-AP nanoparticles was investigated in batch experiments with varying contact time, solution pH and temperature. Results illustrated that the adsorption of Cu(II) was very rapid during the initial adsorption period. The adsorption capacity of PGA-AP nanoparticles for Cu(II) was increased with the increase in the γ-PGA content, solution pH and temperature. At a pH of 6 and 60 °C, a higher equilibrium adsorption capacity of about 74.80 mg/g was obtained. The kinetic studies indicated that Cu(II) adsorption onto PGA-AP nanoparticles obeyed well the pseudo-second order model. The Langmuir isotherm model was fitted well to the adsorption equilibrium data. The results indicated that the adsorption behavior of PGA-AP nanoparticles for Cu(II) was mainly a monolayer chemical adsorption process. The maximum adsorption capacity of PGA-AP nanoparticles was estimated to be 78.99 mg/g.

scholarly journals Mg-Cr Layered Double Hydroxide with Intercalated Oxalic Anion for Removal Cationic Dyes Rhodamine B and Methylene Blue

2020 ◽  
Vol 9 (1) ◽  
pp. 85-94
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Layered Double Hydroxide ◽  
Rhodamine B ◽  
Physical Adsorption ◽  
Dye Adsorption ◽  
Kinetic Studies ◽  
Economic Feasibility ◽  
Order Kinetic ◽  
Double Hydroxide

A MgCr-based layered double hydroxide (LDH) was synthesized by a coprecipitation method, followed by an intercalation process using an oxalic anion. The materials were characterized using X-ray diffraction analysis, FT-IR spectroscopy, and pH pzc measurement. The materials were then applied as adsorbents for removal of methylene blue (MB) and rhodamine B (RhB) from aqueous solution. Pristine Mg/Cr LDH exhibited RhB adsorption capacity of 32.154 mg g⁻1, whereas the use of intercalated Mg/Cr LDH caused an increase in the capacity (139.526 mg g⁻1). Kinetic studies indicated that the dye adsorption using both LDHs followed a pseudo-second-order kinetic model; the K2 values of pristine and modified Mg/Cr LDH for RhB and MB were 6.970, 0.001, 0.426, and 2.056 g mg⁻1 min⁻1, respectively. The thermodynamic study identified that the adsorption of both dyes onto the LDHs was a spontaneous process and can be classified as physical adsorption with adsorption energies of <40 kJ/mol. Moreover, the desorption and regeneration experiments indicated the high economic feasibility and reusability of the LDHs. By using HCl as the optimal solvent, the LDHs could desorb as much as 98% of the dye and could be used as adsorbents with high adsorption capacity over three cycles.

scholarly journals Super-Adsorbent Hydrogels for Removal of Methylene Blue from Aqueous Solution: Dye Adsorption Isotherms, Kinetics, and Thermodynamic Properties

Macromol ◽  
2021 ◽  
Vol 1 (4) ◽  
pp. 256-275
Author(s):  
Buddhabhushan Salunkhe ◽  
Thomas P. Schuman
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Polymer Network ◽  
Dye Adsorption ◽  
Isotherm Models ◽  
High Adsorption ◽  
High Adsorption Capacity ◽  
Efficient Option ◽  
Sodium Styrenesulfonate

Removal of dyes through adsorption from wastewater has gained substantial interest in recent years, especially in development of hydrogel based adsorbents, owing to their easy use and economical nature. The aim of the present study was to design a super-adsorbent hydrogel based on sodium styrenesulfonate (NaSS) monomer for removal of dyes like methylene blue (MB). NaSS displays both an aromatic ring and strongly ionic group in its monomer structure that can enhance adsorption capacity. Poly(sodium styrenesulfonate-co-dimethylacrylamide) hydrogels were prepared by solution free radical polymerization using gelatin methacryloyl (GelMA) as crosslinker, creating a highly porous, three-dimensionally crosslinked polymer network contributing to higher swelling ratios of up to 27,500%. These super-adsorbent hydrogels exhibited high adsorption capacity of 1270 mg/g for MB adsorption with above 98% removal efficiency. This is the first report for such a high adsorption capacity for dye absorbance for NaSS-based hydrogels. Additionally, the adsorption kinetics using a pseudo-first-order and the Freundlich adsorption isotherm models for multilayer, heterogeneous adsorption processes has been reported. The adsorbents’ reusability was confirmed through 4 repeated cycles of desorption-adsorption. The results discussed herein illustrate that NaSS based chemistries can be used as an efficient option for removal of organic dyes from contaminated wastewater.

scholarly journals Selective and Recyclable Congo Red Dye Adsorption by Spherical Fe3O4 Nanoparticles Functionalized with 1,2,4,5-Benzenetetracarboxylic Acid

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Sobhan Chatterjee ◽  
Nikita Guha ◽  
Sarathkumar Krishnan ◽  
Amrendra K. Singh ◽  
Pradeep Mathur ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Congo Red ◽  
Dye Adsorption ◽  
Kinetic Studies ◽  
Average Diameter ◽  
Adsorption Model ◽  
Mechanism Study ◽  
New Material ◽  
Co Precipitation ◽  
Red Dye

AbstractIn this study, the new material Fe3O4@BTCA has been synthesized by immobilization of 1,2,4,5-Benzenetetracarboxylic acid (BTCA) on the surface of Fe3O4 NPs, obtained by co-precipitation of FeCl3.6H2O and FeCl2.4H2O in the basic conditions. Characterization by P-XRD, FE-SEM, and TEM confirm Fe3O4 has a spherical crystalline structure with an average diameter of 15 nm, which after functionalization with BTCA, increases to 20 nm. Functionalization also enhances the surface area and surface charge of the material, confirmed by BET and zeta potential analyses, respectively. The dye adsorption capacity of Fe3O4@BTCA has been investigated for three common dyes; Congo red (C.R), Methylene blue (M.B), and Crystal violet (C.V). The adsorption studies show that the material rapidly and selectively adsorbs C.R dye with very high adsorption capacity (630 mg/g), which is attributed to strong H-bonding ability of BTCA with C.R dye as indicated by adsorption mechanism study. The material also shows excellent recyclability without any considerable loss of adsorption capacity. Adsorption isotherm and kinetic studies suggest that the adsorption occurs by the Langmuir adsorption model following pseudo-second-order adsorption kinetics.

scholarly journals Study on Adsorption of Nickel and Methylene Blue in Aqueous Solution by Magnetic Carboxylate-Rich Carbon

2021 ◽  
Vol 37 (2) ◽  
Author(s):  
Doan Van Dat ◽  
Nguyen Hoai Thuong ◽  
Tran Thi Kieu Ngan ◽  
Le Thi Thanh Nhi ◽  
Dao My Uyen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Endothermic Process ◽  
High Adsorption Capacity

In this study, magnetic carboxylate-rich carbon material (Fe3O4@CRC) was synthesized via a low-temperature carbonization method and applied as an adsorbent for adsorption of Ni(II) ions and methylene blue (MB) in aqueous solution. The synthesized Fe3O4@CRC was characterized by various techniques (XRD, FTIR, FE-SEM, TEM, EDX, VSM, and BET). The adsorption kinetics, isotherms, thermodynamics, and the effects of key adsorption factors, including the pH value, initial adsorbate concentration, contact time, adsorbent dose and temperature were investigated in detail. The results showed that Fe3O4@CRC exhibited a high adsorption capacity for MB and Ni(II) with the maximum adsorption capacity of 187.26 mg/g and 106.75 mg/g, respectively. The adsorption of MB and Ni(II) on Fe3O4@CRC was a spontaneous and endothermic process, and was best described with the first-order kinetic model, Freundlich (for MB) and Langmuir (for Ni(II)) isotherm models. In addition, Fe3O4@CRC could maintain a high adsorption capacity after many consecutive cycles. Therefore, the Fe3O4@CRC material can be used as a highly efficient adsorbent for the removal of heavy metals and dyes from wastewater due to the advantages of high adsorption performance, easy separation, and good reusability.  

Sign in / Sign up

Export Citation Format

Share Document