Study on Pure Aqueous Extraction Method of PHB/Ectoine Co-Products Based on Osmotic Downshock

2014 ◽  
Vol 955-959 ◽  
pp. 3377-3380 ◽  
Author(s):  
Qing Chen ◽  
Te Wang ◽  
Jin Dan Zhao ◽  
Fu Hui Kang ◽  
Yi Ming Zhang ◽  
...  
Keyword(s):  
Ion Exchange ◽  
Hollow Fiber ◽  
Extraction Method ◽  
Pure Water ◽  
Aqueous Extraction ◽  
Extraction Rate ◽  
Extraction Temperature ◽  
Optimal Conditions ◽  
Pressure Extraction ◽  
Osmotic Downshock

The simultaneously co-production of Poly-β-hydroxybutyrate (PHB) and ectoine in a process (PHB/Ect co-production) and co-products extraction have great significant for reducing the manufacture cost and promoting industrialization of PHB and ectoine. The pure aqueous extraction method based on osmotic downshock was used for the extraction of PHB/Ect co-products byH. salina. The effects of osmotic pressure, extraction temperature and extraction time on the extraction rate of PHB were investigated. The ectoine was extracted and purified by the techniques of hollow fiber and ion exchange. The optimal conditions for PHB extraction were osmotic downshock in pure water, extraction temperature at 60 °C and extraction for 4 h. The extraction rate of PHB was 87.5%. The extraction rate of ectoine was 84.2%.

Studies on the Aqueous Extraction Method of Sesame Oil

2013 ◽  
Vol 634-638 ◽  
pp. 1542-1547 ◽  
Author(s):  
Li Xia Hou ◽  
Xiao Lei Shang ◽  
Xiao Xia Wang ◽  
Jing Liu ◽  
Lei Zhou
Keyword(s):  
Extraction Method ◽  
Oil Extraction ◽  
Sesame Oil ◽  
Aqueous Extraction ◽  
Extraction Rate ◽  
Optimal Conditions ◽  
Single Factor ◽  
Technological Parameters ◽  
Single Factor Experiment ◽  
Water Ratio

The aqueous extracting method of sesame oil was studied in this paper．On basis of the single-factor experiment, the orthogonal trial was used in optimization of technological parameters. The optimal conditions for sesame oil extraction were solid to water ratio of 0.8 g/ml (v/w), 70°Cand pH 5.0, under which the extraction rate reached 82.49％．

Study on Synthesis of PHB by Moderate Halophile and Aqueous Extraction of PHB

2013 ◽  
Vol 448-453 ◽  
pp. 160-163
Author(s):  
Qing Chen ◽  
Ling Hua Zhang
Keyword(s):  
Extraction Efficiency ◽  
Rate Increase ◽  
Sodium Dodecyl ◽  
Halophilic Bacterium ◽  
Aqueous Extraction ◽  
Extraction Rate ◽  
Moderate Halophile ◽  
Extraction And Purification ◽  
Nacl Concentration ◽  
Osmotic Downshock

PHB (Poly-β-hydroxybutyrate) has been widely in the areas of industrial packaging, pharmacy and agriculture. Currently, its production cost, especially in extraction and purification are high. A moderate halophilic bacterium was used for PHB synthesis and an aqueous extraction method based on osmotic downshock was investigated in this paper to further improve the extraction efficiency. PHB synthesised by moderate halophile with certain NaCl concentration can be released with cell lysis by osmotic downshock. Meanwhile the high temperature, ultrasonic and SDS (Sodium dodecyl sulfate) can enhance the release. After 48 h of fermentation, the production of PHB by Halomonas salina was 6.5 g/L. The extraction rate of PHB was 24.6% with osmotic downshock and 35.4% with additional ultrasonic assistance at 65 °C. A further addition of 0.5% SDS made the extraction rate increase to 75.4%. Thereinto, the addition of 6% NaCl had significantly improved the aqueous extraction rate to 92.3%.

scholarly journals Orthogonal Optimization of Polysaccharide Extraction from Millet Bran

2019 ◽  
Vol 78 ◽  
pp. 02011
Author(s):  
Songling Cai ◽  
Min Pang
Keyword(s):  
Extraction Method ◽  
Extraction Process ◽  
Orthogonal Test ◽  
Extraction Rate ◽  
Extraction Time ◽  
Alkali Concentration ◽  
Extraction Temperature ◽  
Solid Ratio ◽  
Optimum Parameters ◽  
Orthogonal Optimization

This paper investigated the effects of liquid-solid ratio, extraction time, extraction temperature and alkali concentration on the extraction rate of millet bran polysaccharides by the enzymatic hydrolysis and alkaline extraction method, then the L9 (34) orthogonal test was designed to optimize the extraction process according to the single factor experiment.The optimum parameters were obtained as follow: 15:1 liquid-solid ratio, five hours extraction time, 80° extraction temperature, and 0.7 mol/l concentration of sodium hydroxide. The extraction rate of millet bran polysaccharide reached 11.46% through the verification experiments under these conditions,and the RSD was 1.79%. Therefore, it can provide some experimental basis for the scientific research of millet bran polysaccharides in the future.

scholarly journals Optimization of Ultrasonic Cellulase-Assisted Extraction and Antioxidant Activity of Natural Polyphenols from Passion Fruit

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2494
Author(s):  
Wei Wang ◽  
Yu-Ting Gao ◽  
Ji-Wen Wei ◽  
Yin-Feng Chen ◽  
Qing-Lei Liu ◽  
...  
Keyword(s):  
Antioxidant Activity ◽  
Extraction Method ◽  
Ph Value ◽  
Soxhlet Extraction ◽  
Passion Fruit ◽  
Total Phenol Content ◽  
Extraction Temperature ◽  
Scavenging Activity ◽  
Solid Ratio ◽  
Dpph Scavenging

In this paper, ultrasonic cellulase extraction (UCE) was applied to extract polyphenols from passion fruit. The extraction conditions for total phenol content (TPC) and antioxidant activity were optimized using response surface methodology (RSM) coupled with a Box-Behnken design (BBD). The results showed that the liquid-to-solid ratio (X2) was the most significant single factor and had a positive effect on all responses. The ANOVA analysis indicated quadratic models fitted well as TPC with R2 = 0.903, DPPH scavenging activity with R2 = 0.979, and ABTS scavenging activity with R2 = 0.981. The optimal extraction parameters of passion fruit were as follows: pH value of 5 at 30 °C for extraction temperature, 50:1 (w/v) liquid-to-solid ratio with extraction time for 47 min, the experimental values were found matched with those predicted. Infrared spectroscopy suggested that the extract contained the structure of polyphenols. Furthermore, three main polyphenols were identified and quantified by HPLC. The results showed the content of phenolic compounds and antioxidant activity of the optimized UCE were 1.5~2 times higher than that determined by the single extraction method and the Soxhlet extraction method, which indicates UCE is a competitive and effective extraction technique for natural passion fruit polyphenols.

scholarly journals Hydrophilic Dual Layer Hollow Fiber Membranes for Ultrafiltration

Membranes ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 143
Author(s):  
Lara Grünig ◽  
Ulrich A. Handge ◽  
Joachim Koll ◽  
Oliver Gronwald ◽  
Martin Weber ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Hollow Fiber ◽  
Triblock Copolymer ◽  
Pure Water ◽  
Vinyl Pyrrolidone ◽  
Scattering Data ◽  
Coupling Mechanism ◽  
Additive Concentration ◽  
Hollow Fiber Membranes ◽  
Fiber Membranes

In this study, a triblock copolymer was used as additive to fabricate new dual layer hollow fiber membranes with a hydrophilic active inner surface in order to improve their fouling resistance. The polymeric components of the solutions for membrane fabrication were poly(ether sulfone), poly(N-vinyl pyrrolidone), and the triblock copolymer. The additive consists of three blocks: a middle hydrophobic poly(ether sulfone) block and two outer hydrophilic alkyl poly(ethylene glycol) blocks. By varying the additive concentration in the solutions, it was possible to fabricate dual layer hollow fiber membranes that are characterized by a hydrophilic inner layer, a pure water permeance of over 1800 L/(m2 bar h) and a molecular weight cut-off of 100 kDa similar to commercial membranes. Contact angle and composition determination by XPS measurements revealed the hydrophilic character of the membranes, which improved with increasing additive concentration. Rheological, dynamic light scattering, transmission, and cloud point experiments elucidated the molecular interaction, precipitation, and spinning behavior of the solutions. The low-molecular weight additive reduces the solution viscosity and thus the average relaxation time. On the contrary, slow processes appear with increasing additive concentration in the scattering data. Furthermore, phase separation occurred at a lower non-solvent concentration and the precipitation time increased with increasing additive content. These effects revealed a coupling mechanism of the triblock copolymer with poly(N-vinyl pyrrolidone) in solution. The chosen process parameters as well as the additive solutions provide an easy and inexpensive way to create an antifouling protection layer in situ with established recipes of poly(ether sulfone) hollow fiber membranes. Therefore, the membranes are promising candidates for fast integration in the membrane industry.

Preparation and Characterization of Hydrophilic PVDF Hollow Fiber Ultrafiltration Membrane

2011 ◽  
Vol 480-481 ◽  
pp. 201-206
Author(s):  
Li Guo Wang ◽  
Xiu Ju Wang ◽  
Ai Min Wang ◽  
Wen Juan Liu ◽  
Shi Qi Guo ◽  
...  
Keyword(s):  
Acrylic Acid ◽  
Hollow Fiber ◽  
Polyvinylidene Fluoride ◽  
Breaking Strength ◽  
Pure Water ◽  
Water Flux ◽  
Technical Parameters ◽  
Rupture Pressure ◽  
Pure Water Flux

Hydrophilic Polyvinylidene fluoride (PVDF) hollow fiber ultrafiltration membranes were prepared by wet-spinning method. The effects of technical parameters of acrylic acid grafted onto PVDF on the performance of hydrophilic PVDF membranes were investigated via orthogonal test, the technical parameters of preparation of hydrophilic PVDF membranes were determined, and hydrophilic PVDF membranes were prepared. Then hydrophilic PVDF membranes were characterized in terms of breaking strength, breaking elongation, rupture pressure, pure water flux and rejection. The fouling properties and the conditions of acrylic acid grafted onto PVDF were also examined. The results showed that acrylic acid had been grafted onto PVDF, the breaking strength and rupture pressure improved greatly, and the fouling properties were better than PS hollow fiber UF membrane.

Microwave-Assisted Extraction of Chlorophyll from Filter Mud of Sugercane Mill and Component Analysis

2012 ◽  
Vol 518-523 ◽  
pp. 430-435 ◽  
Author(s):  
Hai Rong Guo ◽  
Shao Ying Ma ◽  
Xiao Fei Wang ◽  
Er Fang Ren ◽  
Yuan Yuan Li
Keyword(s):  
Irradiation Time ◽  
Extraction Time ◽  
Extraction Temperature ◽  
Microwave Assisted Extraction ◽  
Optimal Conditions ◽  
Microwave Assisted ◽  
Assisted Extraction ◽  
Conventional Extraction ◽  
Filter Mud ◽  
Strong Absorption Peak

Microwave-assisted extraction (MAE) was used to extract chlorophylls from filter mud. Ethanol was used as the solvent. The optimal conditions for the MAE of chlorophylls were concluded from the study as the irradiation time, 50 s, the ratio of liquid to solid, 8:1 (mL/g), the extraction temperature, 40 °C, and the extraction time, 60 min. Compared with conventional extraction, the MAE of chlorophylls from the filter mud was more effective. The extraction time for MAE was 60 min with 0.277 mg/g chlorophyll yield, while conventional extraction needed 240 min with only about 0.259 mg/g chlorophyll yield. The Ultraviolet Absorption Spectra of the extracted chlorophylls showed that there was a strong absorption peak at about 663 nm. C=N, Mg-N and C-N was not seen existed from the infrared spectroscopy probably because that the mixed extracts were not purified and the chlorophyll content was less.

Optimization of the Ultrasonic Extraction of Gypenoside III from Gynostemma pentaphyllum by Response Surface Methodology

2012 ◽  
Vol 550-553 ◽  
pp. 1866-1870
Author(s):  
Xiao Dan Tang ◽  
Hai Yang Hang ◽  
Shao Yan Wang ◽  
Jing Xiang Cong
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Extraction Yield ◽  
Raw Material ◽  
Extraction Temperature ◽  
Optimal Conditions ◽  
Gynostemma Pentaphyllum ◽  
Bioactive Component ◽  
Yield Value ◽  
Ultrasonic Time

Gypenosides III is a major bioactive component which is rich in Gynostemma pentaphyllum. For better utilization of the native resource, response surface methodology was used to optimize the extraction conditions of gypenosides III from G. pentaphyllum. The effects of three independent variables on the extraction yield of gypenosides III were investigated and the optimal conditions were evaluated by means of Box-Behnken design. The optimal conditions are as follows: ratio of ethanol to raw material 25, extraction temperature 58°C and ultrasonic time 25min. Under these conditions, the yield of gypenoside III is 1.216±0.05%, which is agreed closely with the predicted yield value.

Ion exchange fabric synthesized by graft polymerization and its application to ultra-pure water production

2010 ◽  
Vol 79 (3) ◽  
pp. 223-226 ◽  
Author(s):  
T. Takeda ◽  
M. Tamada ◽  
N. Seko ◽  
Y. Ueki
Keyword(s):  
Ion Exchange ◽  
Graft Polymerization ◽  
Pure Water ◽  
Water Production ◽  
Ultra Pure Water

Extraction Process of Amaranthine Pigment Keeping the Water Wax Fuit Biological Active

2013 ◽  
Vol 295-298 ◽  
pp. 150-154
Author(s):  
Feng Jie Wang ◽  
Xin Qiao Dong ◽  
Xiao Liu
Keyword(s):  
Citric Acid ◽  
Extraction Method ◽  
Raw Materials ◽  
Extraction Process ◽  
Extraction Yield ◽  
Extraction Temperature ◽  
Natural Pigment ◽  
Pigment Extraction ◽  
Acid Aqueous Solution ◽  
The Stability

Development natural pigment retained a variety of nutrition composition is extremely research value.Water Wax Trees Fruit was as raw materials,citric acid aqueous solution was as extracting agent.Amaranthine pigment extraction method were studied on fully grasping the stability of the natural amaranthine pigment and no damage to the water wax fruit biological activity.The effect of extraction yield were studied on Water Wax Trees Fruit natural amaranthine pigment.The results show that the better extraction conditions are extraction temperature at 70 °C, extraction time for 3h,citric acid concentration1.0 % , the material/liquid ration(g/ml) 1:5.The extraction yield is 2.95%.Ultraviolet absorption maximum wavelength is 280 nm.

Sign in / Sign up

Export Citation Format

Share Document