Impact of Tooth Shape Parameters on Strength Safety Coefficient of Herringbone Planetary Train

2014 ◽  
Vol 989-994 ◽  
pp. 2753-2757
Author(s):  
Zeng Bao Zhu ◽  
Chao Qun Shu ◽  
Ying Li Xu ◽  
Can Li ◽  
Min Yin
Keyword(s):  
Bending Strength ◽  
High Strength ◽  
Tip Clearance ◽  
Shape Parameters ◽  
Tooth Shape ◽  
Safety Coefficient ◽  
Lubrication Condition ◽  
Spiral Angle ◽  
The Impact ◽  
Train System

The influence of tooth profile parameters on the strength safety coefficient can provides the basis for the design of high strength herringbone planetary train system. Through calculation of the three strength safety coefficients (contact strength, bending strength, bonding strength), curves of the relationships between the tooth shape parameters (addendum coefficient, tip clearance coefficient, spiral angle) and the strength safety coefficients have been obtained and the impact of tooth shape parameters on the three strength safety coefficients have been analyzed. The research results show that the bigger addendum coefficient can be selected for the design of high strength herringbone planetary train system. In order to satisfy bending strength, no-undercut and lubrication condition the smaller tip clearance coefficient should be taken. The strength safety coefficients are bigger with the increase of spiral angle, so a bigger spiral angle may be appropriately chosen.

scholarly journals INCREASING IN IMPACT VISCOSITY OF FIBER-ASH-CONCRETE

2021 ◽  
Vol 3 (6) ◽  
pp. 5-16
Author(s):  
R. Fedyuk ◽  
Yu. Liseycev ◽  
A. Taskin ◽  
R. Timohin ◽  
Sergey Klyuev ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Building Materials ◽  
Bending Strength ◽  
Materials Science ◽  
Basalt Fiber ◽  
Dynamic Strength ◽  
High Strength ◽  
Cement Composite ◽  
Fiber Reinforced Concrete ◽  
The Impact

The trend in building materials science is to replace the different proportions of Portland cement in the binder. Therefore, the paper proposes the principles of controlling the static and dynamic strength of fiber-reinforced concrete, consisting in the complex effect of the hydro-removed ash and slag mix and basalt fiber on the processes of structure formation of the cement composite. A four-stage purification system for the hydro-removed ash and slag mixture has been developed, including disintegration, flotation and two-stage magnetic separation. It was found that the density of the fresh mix from the dose behaves naturally, and the density of solid samples at low doses slightly decreases. High early strength of the developed composites is noted, in particular, for specimens with ASM, one and a half increase in compressive strength is traced in comparison with non-additive specimens. Combinations of "fiber + ASM" with a quadrupling of strength have a significant effect on bending strength. Successful approximations of the compressive strength and bending strength on the ASM dose for different ages (1, 7, 28 days) are traced with the regular behavior of the coefficients in the power dependences. Revealed a multiple increase in the impact strength of the developed compositions. The use of the results will lead to the possibility of designing high-strength concretes, including for special structures.

Ceramic Materials. Effects of Fracture Origin and Microstructure on Bending Strength of High-Strength Si3N4.

1994 ◽  
Vol 43 (489) ◽  
pp. 599-605 ◽  
Author(s):  
Akira YAMAKAWA ◽  
Takehisa YAMAMOTO ◽  
Tomoyuki AWAZU ◽  
Kenji MATSUNUMA ◽  
Takao NISHIOKA
Keyword(s):  
Bending Strength ◽  
High Strength ◽  
Ceramic Materials ◽  
Fracture Origin

scholarly journals Impact resistance of steel materials to ballistic ejecta and shelter development using steel deck plates

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Kohei Tateyama ◽  
Shino Naruke ◽  
Hisashi Sasaki ◽  
Shinichi Torigata ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Test ◽  
Impact Resistance ◽  
Protective Layer ◽  
High Strength ◽  
Steel Plates ◽  
Corrugated Plates ◽  
Shelter Construction ◽  
The Impact ◽  
Ballistic Ejecta

AbstractThe destruction caused by ballistic ejecta from the phreatic eruptions of Mt. Ontake in 2014 and Mt. Kusatsu-Shirane (Mt. Moto-Shirane) in 2018 in Japan, which resulted in numerous casualties, highlighted the need for better evacuation facilities. In response, some mountain huts were reinforced with aramid fabric to convert them into shelters. However, a number of decisions must be made when working to increase the number of shelters, which depend on the location where they are to be built. In this study, we propose a method of using high-strength steel to reinforce wooden buildings for use as shelters. More specifically, assuming that ballistic ejecta has an impact energy of 9 kJ or more, as in previous studies, we developed a method that utilizes SUS304 and SS400 unprocessed steel plates based on existing impact test data. We found that SUS304 is particularly suitable for use as a reinforcing material because it has excellent impact energy absorption characteristics due to its high ductility as well as excellent corrosion resistance. With the aim of increasing the structural strength of steel shelters, we also conducted an impact test on a shelter fabricated from SS400 deck plates (i.e., steel with improved flexural strength provided by work-hardened trapezoidal corrugated plates). The results show that the shelter could withstand impact with an energy of 13.5 kJ (2.66 kg of simulated ballistic ejecta at 101 m/s on impact). In addition, from the result of the impact test using the roof-simulating structure, it was confirmed the impact absorption energy is further increased when artificial pumice as an additional protective layer is installed on this structure. Observations of the shelter after the impact test show that there is still some allowance for deformation caused by projectile impact, which means that the proposed steel shelter holds promise, not only structurally, but also from the aspects of transportation and assembly. Hence, the usefulness of shelters that use steel was shown experimentally. However, shelter construction should be suitable for the target environment.

scholarly journals Experimental Investigation on the Influence of Fiber Path Curvature on the Mechanical Properties of Composites

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2602
Author(s):  
Huaqiao Wang ◽  
Jihong Chen ◽  
Zhichao Fan ◽  
Jun Xiao ◽  
Xianfeng Wang
Keyword(s):  
Tensile Strength ◽  
Path Planning ◽  
Composite Laminates ◽  
Bending Strength ◽  
High Strength ◽  
Bending Test ◽  
Fiber Placement ◽  
Automated Fiber Placement ◽  
Fiber Path ◽  
Path Curvature

Automated fiber placement (AFP) has been widely used as an advanced manufacturing technology for large and complex composite parts and the trajectory planning of the laying path is the primary task of AFP technology. Proposed in this paper is an experimental study on the effect of several different path planning placements on the mechanical behavior of laminated materials. The prepreg selected for the experiment was high-strength toughened epoxy resin T300 carbon fiber prepreg UH3033-150. The composite laminates with variable angles were prepared by an eight-tow seven-axis linkage laying machine. After the curing process, the composite laminates were conducted by tensile and bending test separately. The test results show that there exists an optimal planning path among these for which the tensile strength of the laminated specimens decreases slightly by only 3.889%, while the bending strength increases greatly by 16.68%. It can be found that for the specific planning path placement, the bending strength of the composite laminates is significantly improved regardless of the little difference in tensile strength, which shows the importance of path planning and this may be used as a guideline for future AFP process.

scholarly journals Toughness Property Control by Nb and Mo Additions in High-Strength Quenched and Tempered Boron Steels

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 95
Author(s):  
Irati Zurutuza ◽  
Nerea Isasti ◽  
Eric Detemple ◽  
Volker Schwinn ◽  
Hardy Mohrbacher ◽  
...  
Keyword(s):  
Solid Solution ◽  
Transition Temperature ◽  
High Strength ◽  
Unit Size ◽  
Tempered Martensite ◽  
Size Refinement ◽  
Direct Quenching ◽  
Property Control ◽  
The Impact ◽  
Impact Transition Temperature

The synergetic effect on hardenability by combining boron with other microalloying elements (such as Nb, Mo and Nb + Mo) is widely known for high-strength medium carbon steels produced by direct quenching and subsequent tempering treatment. The improvement of mechanical properties could be reached through optimization of different mechanisms, such as solid solution hardening, unit size refinement, strain hardening, fine precipitation hardening and the effect of carbon in solid solution. The current study proposes a procedure for evaluating the contribution of different microstructural aspects on Charpy impact toughness. First, the effect that austenite conditioning has on low-temperature transformation unit sizes and microstructural homogeneity was analysed for the different microalloying element combinations. A detailed crystallographic characterization of the tempered martensite was carried out using electron backscattered diffraction (EBSD) in order to quantify the effect of unit size refinement and dislocation density. The impact of heterogeneity and presence of carbides was also evaluated. The existing equations for impact transition temperature (ITT50%) predictions were extended from ferrite-pearlite and bainitic microstructures to tempered martensite microstructures. The results show that microstructural refinement is most beneficial to strength and toughness while unit size heterogeneity has a particularly negative effect on ductile-to-brittle transition behaviour. By properly balancing alloy concept and processing, steel having a yield strength above 900 MPa and low impact transition temperature could be obtained by direct quenching and tempering.

scholarly journals Ultrahigh Ballistic Resistance of Twisted Bilayer Graphene

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 206
Author(s):  
Qing Peng ◽  
Sheng Peng ◽  
Qiang Cao
Keyword(s):  
Weight Ratio ◽  
High Strength ◽  
Bilayer Graphene ◽  
Energy Propagation ◽  
Dynamic Simulations ◽  
Protective Material ◽  
Impact Performance ◽  
Ballistic Resistance ◽  
Twisted Bilayer Graphene ◽  
The Impact

Graphene is a good candidate for protective material owing to its extremely high stiffness and high strength-to-weight ratio. However, the impact performance of twisted bilayer graphene is still obscure. Herein we have investigated the ballistic resistance capacity of twisted bilayer graphene compared to that of AA-stacked bilayer graphene using molecular dynamic simulations. The energy propagation processes are identical, while the ballistic resistance capacity of the twisted bilayer graphene is almost two times larger than the AA-bilayer graphene. The enhanced capacity of the twisted bilayer graphene is assumed to be caused by the mismatch between the two sheets of graphene, which results in earlier fracture of the first graphene layer and reduces the possibility of penetration.

scholarly journals Tempforming as an Advanced Processing Method for Carbon Steels

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1566
Author(s):  
Anastasiya Dolzhenko ◽  
Rustam Kaibyshev ◽  
Andrey Belyakov
Keyword(s):  
Impact Toughness ◽  
Crack Propagation ◽  
Large Strain ◽  
High Strength ◽  
Close Relation ◽  
Carbon Steels ◽  
Processing Method ◽  
Propagation Mode ◽  
Displacement Curve ◽  
The Impact

The microstructural mechanisms providing delamination toughness in high-strength low-alloyed steels are briefly reviewed. Thermo-mechanical processing methods improving both the strength and impact toughness are described, with a close relation to the microstructures and textures developed. The effect of processing conditions on the microstructure evolution in steels with different carbon content is discussed. Particular attention is paid to tempforming treatment, which has been recently introduced as a promising processing method for high-strength low-alloyed steel semi-products with beneficial combination of strength and impact toughness. Tempforming consists of large strain warm rolling following tempering. In contrast to ausforming, the steels subjected to tempforming may exhibit an unusual increase in the impact toughness with a decrease in test temperature below room temperature. This phenomenon is attributed to the notch blunting owing to easy splitting (delamination) crosswise to the principle crack propagation. The relationships between the crack propagation mode, the delamination fracture, and the load-displacement curve are presented and discussed. Further perspectives of tempforming applications and promising research directions are outlined.

Effect of Spark Plasma Sintering on the Microstructure Evolution and Properties of M3:2 High-Speed Steel

2014 ◽  
Vol 788 ◽  
pp. 329-333
Author(s):  
Rui Zhou ◽  
Xiao Gang Diao ◽  
Jun Chen ◽  
Xiao Nan Du ◽  
Guo Ding Yuan ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Spark Plasma Sintering ◽  
High Speed ◽  
Bending Strength ◽  
Sintering Temperature ◽  
High Speed Steel ◽  
Continuous Heating ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
The Impact

Effects of sintering temperatures on the microstructure and mechanical performance of SPS M3:2 high speed steel prepared by spark plasma sintering was studied. High speed steel sintering curve of continuous heating from ambient temperature to 1200°C was estimated to analyze the sintering processes and sintering temperature range. The sintering temperature within this range was divided into groups to investigate hardness, relative density and microstructure of M3:2 high-speed steel. Strip and quadrate carbides were observed inside the equiaxed grains. SPS sintering temperature at 900°C can lead to nearly full densification with grain size smaller than 20μm. The hardness and bending strength are higher than that of the conventionally powder metallurgy fabricated ones sintered at 1270°C. However, fracture toughness of the high speed steel is lower than that of the conventional powder metallurgy steels. This can be attributed to the shape and distribution of M6C carbides which reduce the impact toughness of high speed steels.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Sign in / Sign up

Export Citation Format

Share Document