In Vitro Compatibility of Hydroxyapatite Nanoparticles (HAp-NPs) for Restoration Purposes of Archaeological Lime-Based Plasters

2019 ◽  
Vol 60 ◽  
pp. 162-173
Author(s):  
Hussein Marey Mahmoud
Keyword(s):  
Calcium Nitrate ◽  
Ammonium Hydroxide ◽  
Experimental Tests ◽  
Bet Surface Area ◽  
Size Analysis ◽  
Hydroxyapatite Nanoparticles ◽  
Pore Size Analysis ◽  
The Stability ◽  
Present Trial

For a number of years, nanomaterials have been considered as a perfect solution to maintain the stability of different cultural heritage materials. In the present trial, hydroxyapatite nanoparticles (HAp-NPs) have been synthesized via the wet chemical reaction of calcium nitrate and ammonium hydroxide. Then, the possible efficiency of HAp-nanoparticles was evaluated to improve restoration formulas for some archaeological lime-based plasters. A broad series of analytical methods, namely OM, FE-SEM, TEM, AFM, XRD and BET surface area-pore size analysis, was selected for characterizing the archaeological samples and to rate the experimental tests. Further, the physical-mechanical behavior of samples was measured. The emulated modifications induced by the HAp-NPs treatment have been evaluated and discussed.

Adsorption characteristics of benzene on biosolid adsorbent

2003 ◽  
Vol 47 (1) ◽  
pp. 83-87
Author(s):  
C. Hung-Lung ◽  
T.-C. Chen ◽  
M.-C. Tsai ◽  
Y.-L. Chen
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Diameter ◽  
Treatment Plant ◽  
Raw Material ◽  
Bet Surface Area ◽  
Size Analysis ◽  
Average Pore ◽  
Pore Size Analysis ◽  
Different Temperatures

This study selected biosolids from a petrochemical wastewater treatment plant as the raw material. The sludge was immersed in 0 to 5 mol l-1 of ZnCl2 solutions and pyrolyzed at different temperatures. When the sludge was pyrolyzed for 30 min at temperatures of 400, 500, 600, and 700°C, the corresponding surface area of the biosolid adsorbent was 46, 401, 921, and 727 m2/g, respectively. Pore size analysis indicated that the mesopore (20 to 500 Å) contributed more than the macropore and micropore in the sludge pyrolytic residue. When the benzene influent concentration was 800 ppmv, the adsorption capacity ranged from 59 to 164 mg/g for different biosolid adsorbents. A larger BET surface area and smaller average pore diameter yielded a larger benzene adsorption capacity.

Simple and efficient ion imprinted polymer for recovery of uranium from environmental samples

2012 ◽  
Vol 65 (4) ◽  
pp. 728-736 ◽  
Author(s):  
V. E. Pakade ◽  
E. M. Cukrowska ◽  
J. Darkwa ◽  
G. Darko ◽  
N. Torto ◽  
...  
Keyword(s):  
Contact Time ◽  
Uranyl Ion ◽  
Bet Surface Area ◽  
Size Analysis ◽  
Ion Imprinted Polymer ◽  
Imprinted Polymer ◽  
Solution Ph ◽  
Retention Capacity ◽  
Pore Size Analysis ◽  
Ion Imprinted

Ion imprinted polymer material (IIP) was prepared by forming ternary complexes of uranyl imprint ion with 1-(prop-2-en-1-yl)-4-(pyridin-2-ylmethyl)piperazine and methacrylic acid followed by thermal copolymerization with ethylene glycol dimethacrylate as the cross-linking monomer in the presence of 1,1′-azobis(cyclohexanecarbonitrile) initiator and 2-methoxy ethanol porogenic solvent. HCl solution (5 mol/L) was used to leach out the uranyl template ion from the IIP particles. Similarly, the control polymer (CP) material was also prepared exactly under the same conditions as the IIP but without the uranyl ion template. Various parameters such as solution pH, initial concentration, aqueous phase volume, sorbent dosage, contact time and leaching solution volumes were investigated. SEM, IR and BET-surface area and pore size analysis were used for the characterization of IIP and CP materials. The extraction efficiency of the IIP and CP was compared using a batch and SPE mode of extraction. The optimal pH for quantitative removal is 4.0–8.0, sorbent amount is 20 mg, contact time is 20 min and the retention capacity is 120 mg of uranyl ion per g of IIP. The IIP prepared demonstrated superior selectivity towards coexisting cations and therefore it can be used for selective removal of uranium from complex matrices.

scholarly journals Removal of Cesium from Radioactive Waste Liquids Using Geomaterials

2021 ◽  
Vol 11 (18) ◽  
pp. 8407
Author(s):  
Haixin Zhang ◽  
Mingze Zhu ◽  
Xiaoyu Du ◽  
Sihan Feng ◽  
Naoto Miyamoto ◽  
...  
Keyword(s):  
Fly Ash ◽  
Radioactive Waste ◽  
Adsorption Capacity ◽  
Raw Materials ◽  
Energy Dispersive Spectrometer ◽  
Bet Surface Area ◽  
Size Analysis ◽  
Experimental Conditions ◽  
Pore Size Analysis ◽  
Contaminated Waste

In this study, we investigated the removal of Cs from aqueous solutions using geomaterials. Adsorption was chosen as an effective method to develop for the removal of Cs from radioactive waste liquids. Geomaterials, including fly ash and slag as raw materials, were prepared as adsorbents using an alkali activator. The materials were characterized by X-ray diffraction (XRD); scanning electron microscopy with energy dispersive spectrometer (SEM-EDS); and BET surface area, pore volume, and pore size analysis. The effects of various parameters, such as pH, contact time, and adsorbent dosage on the adsorption of the Cs were studied. The partition coefficient (PC) as well as the adsorption capacity were evaluated to assess the true performance of the adsorbent in this work. The fly ash-based geomaterials showed a maximum Cs adsorption capacity of 89.32 mg·g−1 and a high PC of 31.02 mg·g−1·mM−1 for the Cs under our experimental conditions. From this work, this method can be regarded being practical for use as a potential adsorbent for treating Cs in wastewater. Furthermore, the immobilization of Cs in geomaterials was explored from a chemical perspective. In conclusion, fly ash-based geomaterials may be a promising option for the treatment and disposal of nuclear-contaminated waste.

Formation and Structure of Casein Micelles in Lactating Mammary Tissue

1970 ◽  
Vol 28 ◽  
pp. 150-151
Author(s):  
Robert J. Carroll ◽  
Marvin P. Thompson ◽  
Harold M. Farrell
Keyword(s):  
Size Distribution ◽  
G Protein ◽  
Milk Proteins ◽  
Mammary Tissue ◽  
Colloidal System ◽  
Casein Micelles ◽  
The Stability

Milk is an unusually stable colloidal system; the stability of this system is due primarily to the formation of micelles by the major milk proteins, the caseins. Numerous models for the structure of casein micelles have been proposed; these models have been formulated on the basis of in vitro studies. Synthetic casein micelles (i.e., those formed by mixing the purified αsl- and k-caseins with Ca2+ in appropriate ratios) are dissimilar to those from freshly-drawn milks in (i) size distribution, (ii) ratio of Ca/P, and (iii) solvation (g. water/g. protein). Evidently, in vivo organization of the caseins into the micellar form occurs in-a manner which is not identical to the in vitro mode of formation.

Kinetics of Various 99mTc-Sn-Pyrophosphate Compounds in the Rat

1977 ◽  
Vol 16 (04) ◽  
pp. 157-162 ◽  
Author(s):  
C. Schümichen ◽  
B. Mackenbrock ◽  
G. Hoffmann
Keyword(s):  
Normal Saline ◽  
Half Life ◽  
Compound A ◽  
Short Half Life ◽  
Low Concentrations ◽  
The Stability ◽  
Kinetics Of ◽  
In Vitro Stability

SummaryThe bone-seeking 99mTc-Sn-pyrophosphate compound (compound A) was diluted both in vitro and in vivo and proved to be unstable both in vitro and in vivo. However, stability was much better in vivo than in vitro and thus the in vitro stability of compound A after dilution in various mediums could be followed up by a consecutive evaluation of the in vivo distribution in the rat. After dilution in neutral normal saline compound A is metastable and after a short half-life it is transformed into the other 99mTc-Sn-pyrophosphate compound A is metastable and after a short half-life in bone but in the kidneys. After dilution in normal saline of low pH and in buffering solutions the stability of compound A is increased. In human plasma compound A is relatively stable but not in plasma water. When compound B is formed in a buffering solution, uptake in the kidneys and excretion in urine is lowered and blood concentration increased.It is assumed that the association of protons to compound A will increase its stability at low concentrations while that to compound B will lead to a strong protein bond in plasma. It is concluded that compound A will not be stable in vivo because of a lack of stability in the extravascular space, and that the protein bond in plasma will be a measure of its in vivo stability.

Reverse torque values of abutment screws after dynamic loading: The effects of sealant agents and the taper of conical connections

2020 ◽  
Author(s):  
Arda Ozdiler ◽  
suleyman dayan ◽  
Burc Gencel ◽  
Gulbahar Isık-Ozkol
Keyword(s):  
Dynamic Loading ◽  
Antibacterial Agent ◽  
In Vitro Study ◽  
Control Group ◽  
Silicone Sealant ◽  
Reverse Torque ◽  
The Stability ◽  
Torque Values ◽  
Chlorhexidine Gel

This in vitro study evaluated the influence of taper angles on the internal conical connections of implant systems and of the application of chlorhexidine gel as an antibacterial agent or a polyvinyl siloxane (PVS) sealant on the reverse torque values of abutment screws after dynamic loading. The current study tested four implant systems with different taper angles (5.4°, 12°, 45°, and 60°). Specimens were divided into three groups: control (neither chlorhexidine gel filled nor silicone sealed), 2% chlorhexidine gel-filled or silicone-sealed group, and group subjected to a dynamic load of 50 N at 1 Hz for 500,000 cycles prior to reverse torque measurements. Quantitative positive correlation was observed between the taper angle degree and the percentage of tightening torque loss. However, this correlation was significant only for the 60° connection groups except in the group in which a sealant was applied ( p = 0.013 for the control group, p = 0.007 for the chlorhexidine group). Percentages of decrease in the torque values of the specimens with silicone sealant application were significantly higher compared with both the control and chlorhexidine groups ( p = 0.001, p = 0.002, p = 0.001, and p = 0.002, respectively, according to the increasing taper angles); the percentage of decrease in torque values due to chlorhexidine application was statistically insignificant when compared with the control group. The application of gel-form chlorhexidine as an antibacterial agent does not significantly affect the stability of the implant–abutment connection under dynamic loads. PVS sealants may cause screw loosening under functional loads.

Using FRET to Measure the Time it Takes for a Cell to Destroy a Virus

2019 ◽  
Author(s):  
Candace E. Benjamin ◽  
Zhuo Chen ◽  
Olivia Brohlin ◽  
Hamilton Lee ◽  
Stefanie Boyd ◽  
...  
Keyword(s):  
Cellular Uptake ◽  
Rhodamine B ◽  
Virus Like Particle ◽  
A Cell ◽  
Viral Nanoparticles ◽  
The Stability ◽  
Open Question ◽  
Viral Surface ◽  
Fret Pair

<div><div><div><p>The emergence of viral nanotechnology over the preceding two decades has created a number of intellectually captivating possible translational applications; however, the in vitro fate of the viral nanoparticles in cells remains an open question. Herein, we investigate the stability and lifetime of virus-like particle (VLP) Qβ - a representative and popular VLP for several applications - following cellular uptake. By exploiting the available functional handles on the viral surface, we have orthogonally installed the known FRET pair, FITC and Rhodamine B, to gain insight of the particle’s behavior in vitro. Based on these data, we believe VLPs undergo aggregation in addition to the anticipated proteolysis within a few hours of cellular uptake.</p></div></div></div>

Applicability of Instability Index for In vitro Protein Stability Prediction

2019 ◽  
Vol 26 (5) ◽  
pp. 339-347 ◽  
Author(s):  
Dilani G. Gamage ◽  
Ajith Gunaratne ◽  
Gopal R. Periyannan ◽  
Timothy G. Russell
Keyword(s):  
Protein Stability ◽  
Caulobacter Crescentus ◽  
Effect Of Temperature ◽  
Instability Index ◽  
Dipeptide Composition ◽  
Experimental Conditions ◽  
The Stability ◽  
Vitro Protein

Background: The dipeptide composition-based Instability Index (II) is one of the protein primary structure-dependent methods available for in vivo protein stability predictions. As per this method, proteins with II value below 40 are stable proteins. Intracellular protein stability principles guided the original development of the II method. However, the use of the II method for in vitro protein stability predictions raises questions about the validity of applying the II method under experimental conditions that are different from the in vivo setting. Objective: The aim of this study is to experimentally test the validity of the use of II as an in vitro protein stability predictor. Methods: A representative protein CCM (CCM - Caulobacter crescentus metalloprotein) that rapidly degrades under in vitro conditions was used to probe the dipeptide sequence-dependent degradation properties of CCM by generating CCM mutants to represent stable and unstable II values. A comparative degradation analysis was carried out under in vitro conditions using wildtype CCM, CCM mutants and two other candidate proteins: metallo-β-lactamase L1 and α -S1- casein representing stable, borderline stable/unstable, and unstable proteins as per the II predictions. The effect of temperature and a protein stabilizing agent on CCM degradation was also tested. Results: Data support the dipeptide composition-dependent protein stability/instability in wt-CCM and mutants as predicted by the II method under in vitro conditions. However, the II failed to accurately represent the stability of other tested proteins. Data indicate the influence of protein environmental factors on the autoproteolysis of proteins. Conclusion: Broader application of the II method for the prediction of protein stability under in vitro conditions is questionable as the stability of the protein may be dependent not only on the intrinsic nature of the protein but also on the conditions of the protein milieu.

In Silico and in Vitro Evaluation of Deamidation Effects on the Stability of the Fusion Toxin DAB389IL-2

2019 ◽  
Vol 16 (4) ◽  
pp. 307-313 ◽  
Author(s):  
Nasrin Zarkar ◽  
Mohammad Ali Nasiri Khalili ◽  
Fathollah Ahmadpour ◽  
Sirus Khodadadi ◽  
Mehdi Zeinoddini
Keyword(s):  
In Silico ◽  
Catalytic Domain ◽  
Md Simulations ◽  
Special Importance ◽  
Native Form ◽  
Vitro Experiment ◽  
In Vitro Experiment ◽  
Pharmaceutical Protein ◽  
The Stability

Background: DAB389IL-2 (Denileukin diftitox) as an immunotoxin is a targeted pharmaceutical protein and is the first immunotoxin approved by FDA. It is used for the treatment of various kinds of cancer such as CTCL lymphoma, melanoma, and Leukemia but among all of these, treatment of CTCL has special importance. DAB389IL-2 consists of two distinct parts; the catalytic domain of Diphtheria Toxin (DT) that genetically fused to the whole IL-2. Deamidation is the most important reaction for chemical instability of proteins occurs during manufacture and storage. Deamidation of asparagine residues occurs at a higher rate than glutamine residues. The structure of proteins, temperature and pH are the most important factors that influence the rate of deamidation. Methods: Since there is not any information about deamidation of DAB389IL-2, we studied in silico deamidation by Molecular Dynamic (MD) simulations using GROMACS software. The 3D model of fusion protein DAB389IL-2 was used as a template for deamidation. Then, the stability of deamidated and native form of the drug was calculated. Results: The results of MD simulations were showed that the deamidated form of DAB389IL-2 is more unstable than the normal form. Also, deamidation was carried by incubating DAB389IL-2, 0.3 mg/ml in ammonium hydrogen carbonate for 24 h at 37o C in order to in vitro experiment. Conclusion: The results of in vitro experiment were confirmed outcomes of in silico study. In silico and in vitro experiments were demonstrated that DAB389IL-2 is unstable in deamidated form.

Role of the anconeus in the stability of a lateral ligament and common extensor origin–deficient elbow: an in vitro biomechanical study

2019 ◽  
Vol 28 (5) ◽  
pp. 974-981 ◽  
Author(s):  
Armin Badre ◽  
David T. Axford ◽  
Sara Banayan ◽  
James A. Johnson ◽  
Graham J.W. King
Keyword(s):  
Biomechanical Study ◽  
Lateral Ligament ◽  
The Stability
Sign in / Sign up

Export Citation Format

Share Document