A Study of the Mechanical Properties and Recrystallization of Two Types of Foil of Aluminium 1050 A

2009 ◽  
Vol 423 ◽  
pp. 137-145
Author(s):  
J. Pérez-Ilzarbe ◽  
J. Fernández Carrasquilla ◽  
C.J. Luis-Pérez
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Experimental Study ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Continuous Casting ◽  
Rolling Process ◽  
Final Thickness ◽  
Rolling Strip ◽  
Different Thickness

An experimental study of the variation of the mechanical properties of sheets of aluminium alloy 1050A due to heat treatment has been carried out. For this purpose, sheets and foils rolled from continuous casting strip (CCS) and from hot rolling strip (HRS) have been prepared in the laboratory. Initially, CCS and HRS had a thickness of 7,5 mm and 3,0 mm respectively. The final thickness achieved in both cases was 0,20 mm. In order to obtain hardening curves for CCS and HRS sheets and foils, specimens of different thickness were taken during the rolling process. Oven treatments were carried out for drawing softening curves of foils. Foil proceeding from CCS presents hardening due to the precipitation of Al3Fe particles at a temperature range of 160°C to 220 °C. HRS foil has a lower hardening in the same range of temperatures owing to its low supersaturation of Fe. Correlation between ultimate tensile strength Rm and Vickers hardness is studied. Micrographies of optical microscopy are offered at hard and recrystallized conditions.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

scholarly journals The Phase Composition and Mechanical Properties of the Novel Precipitation-Strengthening Al-Cu-Er-Mn-Zr Alloy

2020 ◽  
Vol 10 (15) ◽  
pp. 5345
Author(s):  
Sayed Amer ◽  
Olga Yakovtseva ◽  
Irina Loginova ◽  
Svetlana Medvedeva ◽  
Alexey Prosviryakov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Phase Composition ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Precipitation Strengthening ◽  
The Novel ◽  
Annealed Alloy ◽  
Zr Alloy

The microstructure, phase composition, and mechanical properties during heat treatment and rolling of the novel Al-5.0Cu-3.2Er-0.9Mn-0.3Zr alloy were evaluated. A new quaternary (Al,Cu,Mn,Er) phase with possible composition Al25Cu4Mn2Er was found in the as-cast alloy. Al20Cu2Mn3 and Al3(Zr,Er) phases were nucleated during homogenization, and θ″(Al2Cu) precipitates were nucleated during aging. The metastable disc shaped θ″(Al2Cu) precipitates with a thickness of 5 nm and diameter of 100–200 nm were nucleated mostly on the Al3(Zr,Er) phase precipitates with a diameter of 35 nm. The hardness Vickers (HV) peak was found after the annealing of a rolled alloy at 150 °C due to strengthening by θ″(A2Cu) precipitates, which have a larger effect in materials hardness than do the softening processes. The novel Al-Cu-Er-Mn-Zr alloy has a yield strength (YS) of 320–332 MPa, an ultimate tensile strength (UTS) of 360–370 MPa, and an El. of 3.2–4.0% in the annealed alloy after rolling condition.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

Effect of Solution Treatment and Extrusion on the Microstructure and Mechanical Properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr Alloy

2011 ◽  
Vol 197-198 ◽  
pp. 1125-1128 ◽  
Author(s):  
Jing Jiang Nie ◽  
Liang Meng ◽  
Xiu Rong Zhu ◽  
Yong Dong Xu ◽  
Yue Yi Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Time ◽  
Solution Treatment ◽  
Solution Treated ◽  
Microstructure And Mechanical Properties ◽  
Combined Action ◽  
Strength And Ductility

The effect of the combined action of hot work and heat treatment on the microstructure and mechanical properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr (wt. %) (E21) alloy was investigated. Results showed that the solution treatment time of the ingot played a great effect on the mechanical properties of the extruded alloy. With solution treating time of the ingot increasing, the tensile strength of the extruded alloy decreased gradually, but the elongation increased greatly. The best combination of strength and ductility was achieved for the extruded alloy after the ingot solution treated at 520°C for 3 h, extrusion at 400°C and aging at 200°C for 16 h, namely ultimate tensile strength = 331MPa and elongation = 7.1%.

Effect of Heat Treatment Process on Microstructure and Mechanical Properties of SWRS82B Wire Rod

2010 ◽  
Vol 97-101 ◽  
pp. 752-755 ◽  
Author(s):  
Jia Qi Zhang ◽  
Yi Long Liang ◽  
Song Xiang ◽  
Xiao Di Yang ◽  
Ming Yang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Process ◽  
Block Size ◽  
Interlamellar Spacing ◽  
Heat Treatment Process ◽  
Austenitizing Temperature ◽  
Isothermal Temperature

The effect of the heat treatment process parameters on the mechanical properties and microstructure of SWRS82B wire rods were investigated. Specimens were austenitized at 850°C~900°C and held at 500°C~600°C. The results show that the interlamellar spacing and the pearlite block size become finer with the decrease of the isothermal temperature. At the same isothermal temperature condition, the interlamellar spacing decreases with the increase of austenitizing temperature. The fine interlamellar spacing increases the yield strength and ultimate tensile strength.

Microstructure and Mechanical Properties of Al-1.1Mg-0.6Si-0.4Cu Alloy Manufactured by Casting-Forging Integrated Technology

2016 ◽  
Vol 850 ◽  
pp. 762-767
Author(s):  
Shun Cheng Wang ◽  
Dong Fu Song ◽  
Jing Xu ◽  
Kai Hong Zheng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Tensile Fracture ◽  
Forging Process ◽  
T6 Heat Treatment ◽  
Fracture Modes ◽  
Integrated Technology ◽  
Microstructure And Mechanical Properties

In the present investigation the casting-forging integrated technology was adopted to manufacture Al-1.1Mg-0.6Si-0.4Cu alloy automobile brake calipers. The effect of forging pressure on the microstructure and mechanical properties of Al-1.1Mg-0.6Si-0.4Cu alloy calipers were studied. The results showed that the shrinkage porosities and cracks in the Al-1.1Mg-0.6Si-0.4Cu alloy calipers could be removed by the forging process. The ultimate tensile strength and elongation of Al-1.1Mg-0.6Si-0.4Cu alloy calipers increased with the increase of forging pressure. When the forging pressure was 120 MPa, the ultimate tensile strength and elongation of Al-1.1Mg-0.6Si-0.4Cu alloy calipers with T6 heat treatment were 365.3 MPa and 11.5%, which were improved by 22.8% and 38.2%, respectively compared with that of Al-1.1Mg-0.6Si-0.4Cu alloy calipers without forging. The tensile fracture images revealed that the fracture modes of Al-1.1Mg-0.6Si-0.4Cu alloy calipers were more ductile at higher forging pressure.

scholarly journals Microstructure and Mechanical Properties of Aged and Hot Rolled AZ80 Magnesium Alloy Sheets

Crystals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 239 ◽  
Author(s):  
Bing He ◽  
Yaobo Hu ◽  
Tianshuo Zhao ◽  
Qingshan Yao ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Ageing Time ◽  
Rolling Process ◽  
Second Phase ◽  
Texture Intensity ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Basal Type

This study focused on the effects of ageing for various time at 175 °C before hot rolling on microstructure and mechanical properties of AZ80 magnesium alloys. The amount of γ-Mg17Al12 increased in line with ageing time and during the rolling process could facilitate the fine grains and sub-grains, which resulted in an inhomogeneous or bimodal microstructure, and weakening basal-type texture intensity or occurrence of double-peak texture. However, a larger quantity of γ-Mg17Al12 distributed on the matrix in the alloy aged for 240 min, or the precipitates decorating the grain boundaries in the alloy aged for 75 min, were detrimental to the mechanical properties, and lower ultimate tensile strength with elongation were obtained in the two alloys as a result. When the alloy was aged for 200 min, it showed an optimum mechanical property with its yield strength of 281 MPa, ultimate tensile strength of 363 MPa and a medium elongation of 13.3%, which was mainly attributed to the interaction of the hard second phase particles with dislocation movement and the lowest basal-type texture intensity that favored the basal slip.

Sign in / Sign up

Export Citation Format

Share Document