Differential Reflectometry of Fiber Bragg Gratings

2010 ◽  
Vol 437 ◽  
pp. 324-328
Author(s):  
Yuriy N. Kulchin ◽  
Anatoly M. Shalagin ◽  
Oleg B. Vitrik ◽  
Sergey A. Babin ◽  
Anton V. Dyshlyuk ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Measurement Range ◽  
Light Power ◽  
Practical Applications ◽  
Fiber Optic Line ◽  
Optical Layout ◽  
Wide Range ◽  
Fbg Sensors ◽  
Interrogation Technique ◽  
Modulated Signals

A reflectometric approach is proposed for interrogation of multiple fiber Bragg grating (FBG) sensors recorded in a single fiber optic line, based on the differential registration FBGs’ response to a short probing laser pulse using conventional OTDR. A special optical layout has been developed allowing transformation of FBG’s spectrally modulated signals into intensity modulated signals and at the same time eliminating the susceptibility of the system to light power fluctuations. Threshold sensitivity of the method amounted to ~50 μstrain within the measurement range of ~4000 μstrain. The maximum number of FBGs interrogated by the proposed technique is estimated at several hundred, which by far surpasses the requirements of most practical applications. Due to its simplicity, efficiency and usage of conventional OTDR equipment the proposed FBG interrogation technique can find a wide range of applications, in particular in structural health monitoring.

scholarly journals Direct detection of charge and discharge process in supercapacitor by fiber-optic LSPR sensors

Nanophotonics ◽  
2020 ◽  
Vol 9 (5) ◽  
pp. 1071-1079 ◽  
Author(s):  
Siyu Qian ◽  
Xinlong Chen ◽  
Shiyu Jiang ◽  
Qiwen Pan ◽  
Yachen Gao ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Direct Detection ◽  
Low Cost ◽  
The State ◽  
State Of Charge ◽  
Localized Surface Plasmon ◽  
High Price ◽  
Discharge Process ◽  
Practical Applications ◽  
Wide Range

AbstractSupercapacitors with high power density, ultralong lifespan and wide range operating temperature have drawn significant attention in recent years. However, monitoring the state of charge in supercapacitors in a cost-effective and flexible way is still challenging. Techniques such as transmission electron microscopy and X-ray diffraction can analyze the characteristics of supercapacitor well. But with large size and high price, they are not suitable for daily monitoring of the supercapacitors’ operation. In this paper, a low cost and easily fabricated fiber-optic localized surface plasmon resonance (LSPR) probe is proposed to monitor the state of charge of the electrode in a supercapacitor. The Au nanoparticles were loading on the fiber core as LSPR sensing region. In order to implant the fiber in the supercapacitor, a reflective type of fiber sensor was used. The results show that this tiny fiber-optic LSPR sensor can provide online monitoring of the state of charge during the charging and discharging process in situ. The intensity shift in LSPR sensor has a good linear relationship with the state of charge calculated by standard galvanostatic charging and discharging test. In addition, this LSPR sensor is insensitive to the temperature change, presenting a great potential in practical applications.

scholarly journals Chip-scale optical airflow sensor

2022 ◽  
Vol 8 (1) ◽  
Author(s):  
Yumeng Luo ◽  
Xiaoshuai An ◽  
Liang Chen ◽  
Kwai Hei Li
Keyword(s):  
Light Emission ◽  
Fast Response ◽  
Measurement Range ◽  
Pdms Membrane ◽  
Great Promise ◽  
Integration Scheme ◽  
Molding Process ◽  
Practical Applications ◽  
Wide Range ◽  
Airflow Sensor

AbstractAirflow sensors are an essential component in a wide range of industrial, biomedical, and environmental applications. The development of compact devices with a fast response and wide measurement range capable of in situ airflow monitoring is highly desirable. Herein, we report a miniaturized optical airflow sensor based on a GaN chip with a flexible PDMS membrane. The compact GaN chip is responsible for light emission and photodetection. The PDMS membrane fabricated using a droplet-based molding process can effectively transform the airflow stimuli into optical reflectance changes that can be monitored by an on-chip photodetector. Without the use of external components for light coupling, the proposed sensor adopting the novel integration scheme is capable of detecting airflow rates of up to 53.5 ms−1 and exhibits a fast response time of 12 ms, holding great promise for diverse practical applications. The potential use in monitoring human breathing is also demonstrated.

scholarly journals On the Use of Embedded Fiber Optic Sensors for Measuring Early-Age Strains in Concrete

Sensors ◽  
2021 ◽  
Vol 21 (12) ◽  
pp. 4171
Author(s):  
K.K. Santos Silva ◽  
F.A.N. Silva ◽  
T. Mahfoud ◽  
A. Khelidj ◽  
A. Brientin ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Fiber Optic Sensors ◽  
Embedded Sensors ◽  
Industry Data ◽  
Practical Applications ◽  
Alternative Technologies ◽  
Current State ◽  
Wide Range ◽  
Cracking Process ◽  
Concrete Elements

Detailed information about concrete behavior in real structures is an important issue in controlling its performance during its service life, and the use of embedded sensors to obtain desired information such as temperature, onset of the cracking process and evolution of strains, has gained the attention of the building concrete industry. Data obtained using this technology can provide valuable information for decision making about the need for corrective interventions that can ensure the integrity and safety of concrete structures for long period of time. This paper presents a review of the current state-of-the-art of embedded fiber optic sensors used to assess concrete information of a wide range of aspects, comprising: existing alternative technologies, characteristics and advantages, practical applications and future developments. Complementarily, the work presents preliminary results of the use of fiber optic sensors to automatically and continuously perform expansion readings of AAR in concrete elements that facilitate both the storage—with elimination of the usual interruptions for manual readings—and the availability of continuous results of expansion data that are not possible to obtain with usual AAR tests code reading recommendations.

A New Detector System For The HB5 Stem Instrument

1985 ◽  
Vol 43 ◽  
pp. 134-135
Author(s):  
J.M. Cowley
Keyword(s):  
Dark Field ◽  
Detector System ◽  
Electron Holography ◽  
Small Specimen ◽  
Bright Field ◽  
Multiple Images ◽  
Practical Applications ◽  
Wide Range ◽  
Diffraction Patterns ◽  
Operational Modes

The HB5 STEM instrument at ASU has been modified previously to include an efficient two-dimensional detector incorporating an optical analyser device and also a digital system for the recording of multiple images. The detector system was built to explore a wide range of possibilities including in-line electron holography, the observation and recording of diffraction patterns from very small specimen regions (having diameters as small as 3Å) and the formation of both bright field and dark field images by detection of various portions of the diffraction pattern. Experience in the use of this system has shown that sane of its capabilities are unique and valuable. For other purposes it appears that, while the principles of the operational modes may be verified, the practical applications are limited by the details of the initial design.

scholarly journals A Resonant Pressure Microsensor with a Wide Pressure Measurement Range

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 382
Author(s):  
Chao Xiang ◽  
Yulan Lu ◽  
Chao Cheng ◽  
Junbo Wang ◽  
Deyong Chen ◽  
...  
Keyword(s):  
Chemical Mechanical Planarization ◽  
Measurement Range ◽  
Silicon On Insulator ◽  
Anodic Bonding ◽  
Pressure Measurements ◽  
Quality Factors ◽  
Deep Reactive Ion Etching ◽  
Wide Range ◽  
Form Pressure ◽  
Silicon Islands

This paper presents a resonant pressure microsensor with a wide range of pressure measurements. The developed microsensor is mainly composed of a silicon-on-insulator (SOI) wafer to form pressure-sensing elements, and a silicon-on-glass (SOG) cap to form vacuum encapsulation. To realize a wide range of pressure measurements, silicon islands were deployed on the device layer of the SOI wafer to enhance equivalent stiffness and structural stability of the pressure-sensitive diaphragm. Moreover, a cylindrical vacuum cavity was deployed on the SOG cap with the purpose to decrease the stresses generated during the silicon-to-glass contact during pressure measurements. The fabrication processes mainly contained photolithography, deep reactive ion etching (DRIE), chemical mechanical planarization (CMP) and anodic bonding. According to the characterization experiments, the quality factors of the resonators were higher than 15,000 with pressure sensitivities of 0.51 Hz/kPa (resonator I), −1.75 Hz/kPa (resonator II) and temperature coefficients of frequency of 1.92 Hz/°C (resonator I), 1.98 Hz/°C (resonator II). Following temperature compensation, the fitting error of the microsensor was within the range of 0.006% FS and the measurement accuracy was as high as 0.017% FS in the pressure range of 200 ~ 7000 kPa and the temperature range of −40 °C to 80 °C.

scholarly journals Ring-Forming Polymerization toward Perfluorocyclobutyl and Ortho-Diynylarene-Derived Materials: From Synthesis to Practical Applications

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1486
Author(s):  
Eugene B. Caldona ◽  
Ernesto I. Borrego ◽  
Ketki E. Shelar ◽  
Karl M. Mukeba ◽  
Dennis W. Smith
Keyword(s):  
Chemical Resistance ◽  
Structural Features ◽  
Review Article ◽  
Aryl Ether ◽  
Aromatic Rings ◽  
Practical Applications ◽  
Repeat Units ◽  
Wide Range ◽  
Synthetic Routes ◽  
The Cost

Many desirable characteristics of polymers arise from the method of polymerization and structural features of their repeat units, which typically are responsible for the polymer’s performance at the cost of processability. While linear alternatives are popular, polymers composed of cyclic repeat units across their backbones have generally been shown to exhibit higher optical transparency, lower water absorption, and higher glass transition temperatures. These specifically include polymers built with either substituted alicyclic structures or aromatic rings, or both. In this review article, we highlight two useful ring-forming polymer groups, perfluorocyclobutyl (PFCB) aryl ether polymers and ortho-diynylarene- (ODA) based thermosets, both demonstrating outstanding thermal stability, chemical resistance, mechanical integrity, and improved processability. Different synthetic routes (with emphasis on ring-forming polymerization) and properties for these polymers are discussed, followed by their relevant applications in a wide range of aspects.

scholarly journals Sensing of Nickel(II) Ions by Immobilizing Ligands and Using Different SPEs

2021 ◽  
Vol 6 (1) ◽  
pp. 2
Author(s):  
Liliana Anchidin-Norocel ◽  
Sonia Amariei ◽  
Gheorghe Gutt
Keyword(s):  
Bismuth Oxide ◽  
Human Population ◽  
Raw Materials ◽  
Sensor Technology ◽  
Cyclic Voltammogram ◽  
Accurate Analysis ◽  
Nickel Allergy ◽  
Nickel Ions ◽  
Practical Applications ◽  
Wide Range

The aim of this paper is the development of a sensor for the quantification of nickel ions in food raw materials and foods. It is believed that about 15% of the human population suffers from nickel allergy. In addition to digestive manifestations, food intolerance to nickel may also have systemic manifestations, such as diffuse dermatitis, diffuse itching, fever, rhinitis, headache, altered general condition. Therefore, it is necessary to control this content of nickel ions for the health of the human population by developing a new method that offers the advantages of a fast, not expensive, in situ, and accurate analysis. For this purpose, bismuth oxide-screen-printed electrodes (SPEs) and graphene-modified SPEs were used with a very small amount of dimethylglyoxime and amino acid L-histidine that were deposited. A potentiostat that displays the response in the form of a cyclic voltammogram was used to study the electrochemical properties of nickel standard solution with different concentrations. The results were compared and the most sensitive sensor proved to be bismuth oxide-SPEs with dimethylglyoxime (Bi2O3/C-dmgH2) with a linear response over a wide range (0.1–10 ppm) of nickel concentrations. Furthermore, the sensor shows excellent selectivity in the presence of common interfering species. The Bi2O3/C-dmgH2 sensor showed good viability for nickel analysis in food samples (cocoa, spinach, cabbage, and red wine) and demonstrated significant advancement in sensor technology for practical applications.

scholarly journals Novel Bloch wave excitation platform based on few-layer photonic crystal deposited on D-shaped optical fiber

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Esteban Gonzalez-Valencia ◽  
Ignacio Del Villar ◽  
Pedro Torres
Keyword(s):  
Optical Fibers ◽  
High Performance ◽  
Light Propagation ◽  
Fiber Optic ◽  
Layer Structure ◽  
Optical Network ◽  
Building Blocks ◽  
Bloch Wave ◽  
Nanophotonic Devices ◽  
Wide Range

AbstractWith the goal of ultimate control over the light propagation, photonic crystals currently represent the primary building blocks for novel nanophotonic devices. Bloch surface waves (BSWs) in periodic dielectric multilayer structures with a surface defect is a well-known phenomenon, which implies new opportunities for controlling the light propagation and has many applications in the physical and biological science. However, most of the reported structures based on BSWs require depositing a large number of alternating layers or exploiting a large refractive index (RI) contrast between the materials constituting the multilayer structure, thereby increasing the complexity and costs of manufacturing. The combination of fiber–optic-based platforms with nanotechnology is opening the opportunity for the development of high-performance photonic devices that enhance the light-matter interaction in a strong way compared to other optical platforms. Here, we report a BSW-supporting platform that uses geometrically modified commercial optical fibers such as D-shaped optical fibers, where a few-layer structure is deposited on its flat surface using metal oxides with a moderate difference in RI. In this novel fiber optic platform, BSWs are excited through the evanescent field of the core-guided fundamental mode, which indicates that the structure proposed here can be used as a sensing probe, along with other intrinsic properties of fiber optic sensors, as lightness, multiplexing capacity and easiness of integration in an optical network. As a demonstration, fiber optic BSW excitation is shown to be suitable for measuring RI variations. The designed structure is easy to manufacture and could be adapted to a wide range of applications in the fields of telecommunications, environment, health, and material characterization.

scholarly journals Assessment of Linearization Approaches for Multibody Dynamics Formulations

2017 ◽  
Vol 12 (4) ◽  
Author(s):  
Francisco González ◽  
Pierangelo Masarati ◽  
Javier Cuadrado ◽  
Miguel A. Naya
Keyword(s):  
Mechanical System ◽  
Multibody Dynamics ◽  
Equations Of Motion ◽  
Differential Algebraic Equations ◽  
Algebraic Equations ◽  
Practical Applications ◽  
Linearization Methods ◽  
Highly Nonlinear ◽  
Wide Range ◽  
The Way

Formulating the dynamics equations of a mechanical system following a multibody dynamics approach often leads to a set of highly nonlinear differential-algebraic equations (DAEs). While this form of the equations of motion is suitable for a wide range of practical applications, in some cases it is necessary to have access to the linearized system dynamics. This is the case when stability and modal analyses are to be carried out; the definition of plant and system models for certain control algorithms and state estimators also requires a linear expression of the dynamics. A number of methods for the linearization of multibody dynamics can be found in the literature. They differ in both the approach that they follow to handle the equations of motion and the way in which they deliver their results, which in turn are determined by the selection of the generalized coordinates used to describe the mechanical system. This selection is closely related to the way in which the kinematic constraints of the system are treated. Three major approaches can be distinguished and used to categorize most of the linearization methods published so far. In this work, we demonstrate the properties of each approach in the linearization of systems in static equilibrium, illustrating them with the study of two representative examples.

Sign in / Sign up

Export Citation Format

Share Document