Cyclic Behavior of Composite Truss Beam-to-RC Column Joints in MRFS

2016 ◽  
Vol 711 ◽  
pp. 681-689 ◽  
Author(s):  
Piero Colajanni ◽  
Lidia La Mendola ◽  
Alessia Monaco ◽  
Nino Spinella
Keyword(s):  
Concrete Beams ◽  
Numerical Models ◽  
Cyclic Behavior ◽  
Force Transmission ◽  
Joint Region ◽  
Rc Structures ◽  
Framed Structures ◽  
Standard Code ◽  
Strength Capacity ◽  
Steel Truss

In the present paper, the cyclic behavior of beam-to-column joints made up of Hybrid Steel Trussed Concrete Beams (HSTCBs) connected to Reinforced Concrete (RC) piers is investigated. HSTCBs are a typology of composite beam generally constituted by a steel truss with end zone added rebars embedded within a block of concrete cast in place. HSTCBs represent a structural solution for light industrialization in the civil constructions; the main advantages in their use are the higher construction speed with the minimum site labor, the possibility of covering wide spans with low depths and a final economical convenience. For these reasons, they are also increasingly adopted within seismic framed structures. In the present study, the examined joints are representative of framed RC structures subjected to seismic actions and designed according to the current Italian standard code. Cyclic tests are performed and interpreted by means of analytical and numerical models with the aim of verifying the strength capacity and ductility of the system, focusing on both the global behavior and the force transmission between steel truss and concrete in the joint region.

Behaviour of reinforced GFRP bars concrete beams having strengthened splices using CFRP sheets

2021 ◽  
pp. 136943322110015
Author(s):  
Akram S. Mahmoud ◽  
Ziadoon M. Ali
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
New Method ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Strength Capacity ◽  
Cfrp Sheet ◽  
Carbon Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer

When glass fibre-reinforced polymer (GFRP) bar splices are used in reinforced concrete sections, they affect the structural performance in two different ways: through the stress concentration in the section, and through the configuration of the GFRP–concrete bond. This study experimentally investigated a new method for increasing the bond strength of a GFRP lap (two GFRP bars connected together) using a carbon fibre-reinforced polymer (CFRP) sheet coated in epoxy resin. A new splicing method was investigated to quantify the effect of the bar surface bond on the development length, with reinforced concrete beams cast with laps in the concrete reinforcing bars at a known bending span length. Specimens were tested in four-point flexure tests to assess the strength capacity and failure mode. The results were summarised and compared within a standard lap made according to the ACI 318 specifications. The new method for splicing was more efficient for GFRP splice laps than the standard lap method. It could also be used for head-to-head reinforcement bar splices with the appropriate CFRP lapping sheets.

scholarly journals Statistical and Reliability Study on Shear Strength of Recycled Coarse Aggregate Reinforced Concrete Beams

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3321
Author(s):  
Hyunjin Ju ◽  
Meirzhan Yerzhanov ◽  
Alina Serik ◽  
Deuckhang Lee ◽  
Jong R. Kim
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Construction Material ◽  
Safety Margin ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Construction And Demolition Waste ◽  
Demolition Waste ◽  
Rc Structures ◽  
Coarse Aggregates

The consumption of structural concrete in the construction industry is rapidly growing, and concrete will remain the main construction material for increasing urbanization all over the world in the near future. Meanwhile, construction and demolition waste from concrete structures is also leading to a significant environmental problem. Therefore, a proper sustainable solution is needed to address this environmental concern. One of the solutions can be using recycled coarse aggregates (RCA) in reinforced concrete (RC) structures. Extensive research has been conducted in this area in recent years. However, the usage of RCA concrete in the industry is still limited due to the absence of structural regulations appropriate to the RCA concrete. This study addresses a safety margin of RCA concrete beams in terms of shear capacity which is comparable to natural coarse aggregates (NCA) concrete beams. To this end, a database for reinforced concrete beams made of recycled coarse aggregates with and without shear reinforcement was established, collecting the shear specimens available from various works in the existing literature. The database was used to statistically identify the strength margin between RCA and NCA concrete beams and to calculate its safety margin based on reliability analysis. Moreover, a comparability study of RCA beams was conducted with its control specimens and with a database for conventional RC beams.

Laboratory Fast Corrosion Test of Plain Steel Bars in Concrete Beams

2012 ◽  
Vol 535-537 ◽  
pp. 1803-1806
Author(s):  
Shun Bo Zhao ◽  
Peng Bing Hou ◽  
Fu Lai Qu
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Numerical Models ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Uniform Corrosion ◽  
Pure Bending ◽  
Accelerated Corrosion ◽  
Steel Bars ◽  
Bending Length

An experimental study was carried out to examine the non-uniform corrosion of plain steel bars in reinforced concrete beams partially placed in 5% sodium chloride solution under conditions of accelerated corrosion. 4 reinforced concrete beams with different concrete strength were made. The crack distributions of the beams due to pre-loads and expansion of corrosion product, and the sectional corrosion characteristics of plain steel bars are described in detail. The sectional area loss relating to mass loss and change along pure bending length of the beams are discussed. These can be used as the basis of test for further studies to build the numerical models of serviceability of corroded reinforced concrete beams.

Durability of coral-reef-sand concrete beams reinforced with basalt fibre-reinforced polymer bars in seawater

2021 ◽  
pp. 136943322098166
Author(s):  
Wang Xin ◽  
Shi Jianzhe ◽  
Ding Lining ◽  
Jin Yundong ◽  
Wu Zhishen
Keyword(s):  
Coral Reef ◽  
Marine Environment ◽  
Failure Modes ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Initial Stiffness ◽  
Basalt Fibre ◽  
Rc Structures ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer

A combination of coral reef sand (CRS) concrete and fibre-reinforced polymer (FRP) bars provides an effective solution to the durability deficiency in conventional RC structures. This study experimentally investigates the durability of CRS concrete beams reinforced with basalt FRP (BFRP) bars in a simulated marine environment. Flexural tests are conducted on a total of fourteen CRS concrete beams aged in a cyclic wet-dry saline solution at temperatures of 25, 40 and 55°C. The variables comprise the types of reinforcement (steel and BFRP), the aging duration and the temperature. The failure modes, capacities, deflections and crack development of the beams are analysed and discussed. The results indicate that the ultimate load of the beams exhibits no degradation after aging, whereas the failure mode of the BFRP-CRS concrete beams transition from flexure to shear, which is caused by the degradation in the mechanical properties of the stirrups. The aged BFRP-CRS concrete beams show a substantial increase of over 70% in their initial stiffness compared with the control beams (beams without aging) and a substantial decrease in their crack width after aging due to the prolonged maturation of the concrete. Furthermore, a formula for calculating the shear capacity in the existing code is modified by a partial factor equal to 2, which can predict the capacity of a CRS concrete beam reinforced with BFRP bars in a marine environment.

scholarly journals Multiobjective optimal design of reinforced concrete frames using two metaheuristic algorithms

2021 ◽  
Vol 9 (4B) ◽  
Author(s):  
Mehdi Babaei ◽  
◽  
Masoud Mollayi ◽  
Keyword(s):  
Reinforced Concrete ◽  
Optimal Design ◽  
Optimization Problem ◽  
Numerical Models ◽  
Steel Structures ◽  
Metaheuristic Algorithms ◽  
Rc Structures ◽  
Weighted Sum Method ◽  
Rc Frames ◽  
Single Objective

Genetic algorithm (GA) and differential evolution (DE) are metaheuristic algorithms that have shown a favorable performance in the optimization of complex problems. In recent years, only GA has been widely used for single-objective optimal design of reinforced concrete (RC) structures; however, it has been applied for multiobjective optimization of steel structures. In this article, the total structural cost and the roof displacement are considered as objective functions for the optimal design of the RC frames. Using the weighted sum method (WSM) approach, the two-objective optimization problem is converted to a single-objective optimization problem. The size of the beams and columns are considered as design variables, and the design requirements of the ACI-318 are employed as constraints. Five numerical models are studied to test the efficiency of the GA and DE algorithms. Pareto front curves are obtained for the building models using both algorithms. The detailed results show the accuracy and convergence speed of the algorithms.

Strengthening of a Bridge Pier with HPC: Modeling of Restrained Shrinkage Cracking

2016 ◽  
Vol 711 ◽  
pp. 1027-1034 ◽  
Author(s):  
Adriano Reggia ◽  
Sara Sgobba ◽  
Fabio Macobatti ◽  
Cristina Zanotti ◽  
Fausto Minelli ◽  
...  
Keyword(s):  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Numerical Models ◽  
Experimental Tests ◽  
Concrete Bridges ◽  
Restrained Shrinkage ◽  
Shrinkage Cracking ◽  
Rc Structures ◽  
Restrained Shrinkage Cracking

After more than fifty years from the opening of the largely discussed “Autostrada del Sole” Highway in 1964, the infrastructure system in Italy appears marked by the passing of time, similarly to what observed in several other countries worldwide. The great heterogeneity of the Italian landscape has determined a great variety of construction types, such as large span concrete bridges over the northern rivers and large arch concrete bridges over the valleys of the central region. Increment of vehicle traffic and new seismic regulations are setting new requirements to adapt the existing infrastructure, which should be otherwise replaced. Moreover, reinforced concrete (RC) aging and deterioration have led to structural and material degradation, including severe cracking and corrosion. Specialized materials such as High Performance Concrete (HPC) could represent a viable convenient solution for repairing, strengthening and retrofitting of RC structures as both structural capacity and durability can be refurbished. However, alongside high mechanical performance, HPC is characterized by a high cracking sensitivity at very early age, due to its high stiffness and shrinkage. Restrained shrinkage cracking, particularly significant in repaired structures where the existing concrete generates a considerable restraint against the free movement of the repair material, may represent a limit to the effective application of these materials. For this reason, shrinkage compatibility of HPC with the existing concrete substrate needs to be experimentally and numerically assessed. A study is herein presented where, based on experimental tests, different numerical models are developed and compared to assess and eventually minimize the risk of shrinkage cracking in bridge piers strengthened with HPC.

Nonlinear FE simulations of structural behavior parameters of reinforced concrete beam with epoxy-bonded FRP

2015 ◽  
Vol 24 (1-2) ◽  
pp. 35-46 ◽  
Author(s):  
Saptarshi Sasmal ◽  
S. Kalidoss
Keyword(s):  
Reinforced Concrete ◽  
Numerical Models ◽  
Adhesive Layer ◽  
Control Mode ◽  
Hydraulic Actuator ◽  
Element Analysis ◽  
Interfacial Stresses ◽  
Rc Structures ◽  
Laminate Thickness ◽  
Reinforcement Strain

AbstractIn the present study, investigations on fiber-reinforced plastic (FRP) plated-reinforced concrete (RC) beam are carried out. Numerical investigations are performed by using a nonlinear finite element analysis by incorporating cracking and crushing of concrete. The numerical models developed in the present study are validated with the results obtained from the experiment under monotonic load using the servo-hydraulic actuator in displacement control mode. Further, the validated numerical models are used to evaluate the influence of different parameters. It is found from the investigations that increase in the elastic modulus of adhesive layer and CFRP laminate increases the interfacial stresses whereas increase in laminate modulus decreases the displacement and reinforcement strain of the beam. It is also observed that increase in the adhesive layer can largely reduce the interfacial stresses, whereas increase in laminate thickness increases it. However, increase in laminate thickness decreases the displacement and reinforcement strain of the beam significantly. It is mention worthy that increase in laminate length reduces the interfacial stresses, whereas CFRP width change does not affect the interfacial stresses. The study will be useful for the design and practicing engineers for arriving at the FRP-based strengthening schemes for RC structures judiciously.

Sign in / Sign up

Export Citation Format

Share Document