Microstructure and Shape Memory Behavior of Ti-18Nb-6Zr (at.%) Alloy

2021 ◽  
Vol 1016 ◽  
pp. 1368-1373
Author(s):  
Xiao Yun Song ◽  
Wen Jun Ye ◽  
Song Xiao Hui
Keyword(s):  
Shape Memory ◽  
Tensile Deformation ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Martensite Phase ◽  
Air Cooling ◽  
X Ray Diffraction ◽  
Β Phase ◽  
Transmission Electron ◽  
Cold Rolled

The microstructures and shape memory behaviors of Ti-18Nb-6Zr (at.%) alloy subjected to different heat treatments were investigated through optical microscopy (OM), X-ray diffraction (XRD), Transmission electron microscopy (TEM) and tensile tests. Recrystallization occurs in cold-rolled Ti-18Nb-6Zr alloy after solution treatment at 600~800 °C. The cooling rate after solution treatment at 800°C shows a dramatic effect on the microstructure of the alloy. The microstructures for the water quenching (WQ) and oil quenching (OQ) specimens are composed of single α'' martensite phase, while for the air cooling (AC) specimen, the microstructure consists of predominant β phase and a small amount of fine athermal ω phase. During tensile deformation, two-stage yielding is observed in the alloy subjected to 800°C/0.5h/WQ heat treatment. The stress for martensite variants reorientation and the yield stress for plastic deformation are 310MPa and 455MPa, respectievely, and the maximum shape memory strain of 3.1% is obtained with pre-strain of 6%.

Microstructure and Tensile Behavior of Ti-Rich Ti-Ni-Cu Melt-Spun Ribbon

2014 ◽  
Vol 936 ◽  
pp. 1163-1167
Author(s):  
Wen Jun He ◽  
Guang Hui Min ◽  
Oleg Tolochko
Keyword(s):  
Melt Spinning ◽  
Tensile Deformation ◽  
Amorphous Ribbon ◽  
Fracture Morphology ◽  
Tensile Tests ◽  
Tensile Fracture ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Annealed Ribbon ◽  
Martensitic State

Microstructure and mechanical properties of Ti51.5Ni25Cu23.5 ribbon fabricated by melt spinning were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM) and tensile tests. Some B19 martensite crystalline with (011) compound twin was embedded in the mainly amorphous ribbon, while the ribbon annealed at 450°C for 1 h is at fully martensitic state. Annealing process alter the preferential orientation from (022)-B19 to (111)-B19. Tensile fracture stresses of as-spun ribbon and the annealed ribbon are 1257 MPa and 250 MPa, respectively. The tensile fracture morphology of as-spun ribbon shows typical vein fringe while that of the annealed ribbon reveals fine but depth-inhomogeneous dimples. After tensile deformation, the annealed ribbon exhibits typical martensitic detwinning behavior accompanying with the strain contrast.

The Behavior of Phase Transformation Characteristics and Ageing on Alloying Method of CuZnAl Shape Memory Alloy

2007 ◽  
Vol 544-545 ◽  
pp. 487-490
Author(s):  
Gon Seung Yang ◽  
Jung Il Lee ◽  
Woo Yang Jang
Keyword(s):  
Grain Size ◽  
Phase Transformation ◽  
Shape Memory Alloy ◽  
Brittle Fracture ◽  
Shape Memory ◽  
Void Formation ◽  
Solution Treatment ◽  
Martensite Phase ◽  
Β Phase ◽  
Misch Metal

The effect of transformation temperature and phase transformation characteristics by alloying method of CuZnAl shape memory alloy with a small of misch metal and Zr contents were investigated. The addition of misch metal and Zr was very effective for reducing the grain size. After solution treatment, the specimens were post-quench aged or step quenched at 373K to 623K for variation of hardness value. It was found that the hardness value was very increased at 473K and 523K. The fracture mode has been changed from trans granular brittle fracture to ductile fracture with void formation and coalescence by the addition of misch metal and Zr. Ageing of the β-phase decreased the Ms temperature, but that of the martensite phase increases the As temperature. The change in As temperature with post-quench aging can be attributed to recovery of order in the β-phase.

Shape Memory Effect in New Ti-Nb-Ta Alloy

2017 ◽  
Vol 889 ◽  
pp. 165-170 ◽  
Author(s):  
Alaa Mahmoud Keshtta ◽  
Mohamed Abdel Hady Gepreel
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Martensite Phase ◽  
Bending Tests ◽  
Β Phase ◽  
Arc Melting ◽  
Solution Treated ◽  
Cold Rolled ◽  
Rolled Wire

Recently, Ni-free shape memory Ti-based alloys (composed of the biocompatible β-stabilizing elements such as Ta and Nb) are extensively studied. In this work, new Ni-free Ti-17Nb-6Ta is presented as a candidate for shape memory alloys with high biocompatibility. This alloy produced using arc-melting in argon atmosphere, followed by solution annealing at 900° C for 30 min. β-phase is the predominant phase beside α” martensite phase. Stress induced martensitic transformation is observed after cold rolling and during bending tests as measured by XRD. The hardness of the bended wire in the solution treated condition was around 330HV. While the cold rolled wire hardness before bending was 300 HV. The superelasticity and shape memory effect was investigated through bending tests of alloy wires. The cold rolled wire showed higher superelasticity than shape memory effect. But superelasticity and the shape memory effect were almost similar with the solution treated wire. Also, the total spring back in cold rolled wire is higher compared with solution treated wire.

Characterization of the Phase Transformations in the Shape Memory Alloy Ni-36 at.% Al

1991 ◽  
Vol 246 ◽  
Author(s):  
J.A. Horton ◽  
E.P. George ◽  
C.J. Sparks ◽  
M.Y. Kao ◽  
O.B. Cavin ◽  
...  
Keyword(s):  
High Temperature ◽  
Shape Memory ◽  
Phase Transformations ◽  
Hot Extrusion ◽  
Exothermic Peak ◽  
Nickel Aluminum ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron

AbstractA survey by differential scanning calorimetry (DSC) and recovery during heating of indentations on a series of nickel-aluminum alloys showed that the Ni-36 at.% Al composition has the best potential for a recoverable shape memory effect at temperatures above 100°C. The phase transformations were studied by high temperature transmission electron microscopy (TEM) and by high temperature x-ray diffraction (HTXRD). Quenching from 1200°C resulted in a single phase, fully martensitic structure. The initial quenched-in martensites were found by both TEM and X-ray diffraction to consist of primarily a body centered tetragonal (bct) phase with some body centered orthorhombic (bco) phase present. On the first heating cycle, DSC showed an endothermic peak at 121°C and an exothermic peak at 289°C, and upon cooling a martensite exothermic peak at 115° C. Upon subsequent cycles the 289°C peak disappeared. High temperature X-ray diffraction, with a heating rate of 2°C/min, showed the expected transformation of bct phase to B2 between 100 and 200°C, however the bco phase remained intact. At 400 to 450°C the B2 phase transformed to Ni2Al and Ni5Al3. During TEM heating experiments a dislocation-free martensite transformed reversibly to B2 at temperatures less than 150°C. At higher temperatures (nearly 600°C) 1/3, 1/3, 1/3 reflections from an ω-like phase formed. Upon cooling, the 1/3, 1/3, 1/3 reflections disappeared and a more complicated martensite resulted. Boron additions suppressed intergranular fracture and, as expected, resulted in no ductility improvements. Boron additions and/or hot extrusion encouraged the formation of a superordered bct structure with 1/2, 1/2, 0 reflections.

Effect of Nitrogen Addition on TiNi Shape Memory Alloys

2020 ◽  
Vol 12 (9) ◽  
pp. 1403-1408
Author(s):  
Izaz Ur Rehman ◽  
Tae-Hyun Nam
Keyword(s):  
Mechanical Properties ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
Ternary Alloys ◽  
X Ray Diffraction ◽  
Transformation Temperatures ◽  
Arc Melting ◽  
Type Phase

In present paper we will show how nitrogen effects microstructures, transformation temperatures, and mechanical properties of equiatomic Ti50–Ni50 and Ti-rich Ti51–Ni49 binary shape memory alloys. 0.5 at.% of nitrogen was added to prepare Ti50–Ni49.5–N0.5, and Ti51–Ni48.5–N0.5 (at.%) alloys by arc-melting. Microstructures were investigated by scanning electron microscope (SEM), phase constitutions were investigated by X-ray diffraction (XRD), transformation temperatures were investigated by differential scanning calorimeter (DSC) and mechanical properties were tested by tensile tests. Solutions treated Ti–Ni–N shape memory alloys contain TiNi matrix without nitrogen, Ti2Ni type phase containing a small amount of nitrogen and a new Ti2N type phase containing a small amount of nickel. Compared with Ti50–Ni50 and Ti51–Ni49 binary alloys, the martensitic transformation starts temperatures (Ms) of Ti50–Ni49.5–N0.5 and Ti51–Ni48.5–N0.5 ternary alloys decreased from 63.4 °C to 41.6 °C and from 85.3 °C to 79.4 °C, respectively. By adding N, fracture strain decreased and incomplete superelasticity was observed.

Evaluation of the Mechanical Properties of Glass/Epoxy Composite by Embedding Shape Memory Alloy and Nanoclay

2021 ◽  
Vol 1019 ◽  
pp. 3-11
Author(s):  
Niranjan Pattar ◽  
S.F. Patil ◽  
Pratik Patil ◽  
Iranna Anikivi ◽  
Shridhar Hiremath
Keyword(s):  
Electron Microscopy ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Smart Materials ◽  
Epoxy Composite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Clay Concentration ◽  
Impact Characteristics

Embedding smart materials in the composite to enhance mechanical strength have become a research hotspot owing to their unique properties. The present research also focus on novel way to fabricate composite by embedding Shape Memory Alloy (SMA) wire and montmorillonite (MMT) nanoclay by varying clay concentration (0-7 wt.%). The extent of dispersion of nanoclay in epoxy resin was studied using Transmission Electron Microscopy (TEM) and X-ray diffraction (XRD). Fabricated samples were examined for tensile, flexural and impact characteristics. Scanning Electron Microscopy (SEM) was used to study the adhesion, delamination and damage occurred within the composite due to tensile loading. Results shows that the tensile strength, flexural strength and impact energy of SMA/MMT/glass/epoxy composite was improved by 23%, 21% and 57% respectively, when it was compared with composite with glass/epoxy composite.

In Situ TEM Observation of Phase Transformation for Bio-Medical Shape Memory TiNbSn Alloy

2010 ◽  
Vol 152-153 ◽  
pp. 1755-1758
Author(s):  
Yan Li ◽  
Jie Qi ◽  
Rui Rui Fan ◽  
Chuan Xin Zhai ◽  
Chun Hua Xu
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Shape Memory ◽  
Martensite Phase ◽  
Unit Cell ◽  
Niti Shape Memory Alloy ◽  
Transformation Mechanism ◽  
Cell Parameters ◽  
Β Phase

TiNbSn alloy has high specific strength, low modulus of elasticity, excellent corrosion resistance, no side effects, such as toxic and exhibits shape memory effects after appropriate technical processing. This alloy may substitute as NiTi shape memory alloy to become the new generation of biological materials. It has been reported the studies of this alloy, such as the component and proportion, processing technology, mechanical properties and corrosion resistance. Based on the previous research, the bio-metal material, Ti-10Nb-5Sn alloy was heated and cooled repeatedly in a heater system located in TEM chamber and, at the same time, was observed in situ using a high resolution transmission electron microscope to study the memory property of the alloy and the mechanism of the transformation between austenite β and martensite phase. The results show that, during heating stage from 295K to 400K, the martensite began to dissolve at 355K, and the martensite disappeared completely at 385K, meanwhile, the austenite was created. During cooling stage from 400K to 295K, the martensite begins to take shape at 353K and the transformation was completed at 333K. The alloy can memory the room and high temperature structures, showing two-way memory functions. The high-temperature austenite of Ti-10Nb-5Sn alloy shows body-centered cubic β phase with the unit cell parameter a=0.3283nm; the martensite at room temperature shows orthorhombic NbTi4 phase (M) with the unit cell parameters a=0.3152nm, b=0.4854nm, c=0.4642nm. The orientation relationship between M phase and β phase is , , , , and . The crystal plane , as the habit plane, transforms into during the transformation from β to M phases. The martensite transformation mechanism is that the and transform to and through the tiny migration of atoms.

scholarly journals Microstructure and Mechanical Properties of 4Al Alumina-Forming Austenitic Steel after Cold-Rolling Deformation and Annealing

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2767 ◽  
Author(s):  
Chenchen Jiang ◽  
Qiuzhi Gao ◽  
Hailian Zhang ◽  
Ziyun Liu ◽  
Huijun Li
Keyword(s):  
Grain Size ◽  
Cold Rolling ◽  
Grain Boundaries ◽  
Austenitic Steel ◽  
Rolling Reduction ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Cold Rolling Reduction ◽  
Average Grain Size ◽  
Cold Rolled

Microstructural evolutions of the 4Al alumina-forming austenitic steel after cold rolling with different reductions from 5% to 30% and then annealing were investigated using electron backscattering diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile properties and hardness were also measured. The results show that the average grain size gradually decreases with an increase in the cold-rolling reduction. The low angle grain boundaries (LAGBs) are dominant in the cold-rolled samples, but high angle grain boundaries (HAGBs) form in the annealed samples, indicating that the grains are refined under the action of dislocations. During cold rolling, high-density dislocations are initially introduced in the samples, which contributes to a large number of dislocations remaining after annealing. With the sustaining increase in cold-rolled deformation, the samples exhibit more excellent tensile strength and hardness due to the decrease in grain size and increase in dislocation density, especially for the samples subjected to 30% cold-rolling reduction. The contribution of dislocations on yield strength is more than 60%.

Phase Constitution, Mechanical Property and Corrosion Resistance of the Ti-Nb Alloys

2006 ◽  
Vol 324-325 ◽  
pp. 655-658 ◽  
Author(s):  
Bao Lai Wang ◽  
Yan Bo Wang ◽  
Yu Feng Zheng
Keyword(s):  
Corrosion Resistance ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Artificial Saliva ◽  
X Ray Diffraction ◽  
Phase Constitution ◽  
Β Phase ◽  
Bending Strain ◽  
35Nb Alloy

Recently, people devote to the development of Ni-free shape memory alloys in order to avoid the Ni-hypersensitivity and toxicity and pursue absolute safety. The shape memory effect and superelasticity have been reported in the biomedical Ti-Nb based alloys. The purpose of this paper is to report the phase constitution, tensile property, shape memory effect and corrosion resistance of the Ti-Nb alloys. The phase constitutions of the Ti-Nb alloys are investigated by means of X-ray diffraction (XRD). The results reveal that β+α′′ phases are presented in the Ti-35Nb alloy and only β phase in the Ti-52Nb alloy at room temperature. The tensile test and bending tests indicate that the Ti-35Nb alloy exhibits shape memory effect. The shape recovery ratio is near to 80% when the bending strain is 4.4% and decreases with the increase of the total bending strain. The corrosion resistance of the Ti-Nb alloys in the Hank's solution and artificial saliva (pH=7.4) at 37 are investigated by OCP, Tafel and anodic polarization methods. The results indicate that the Ti-35Nb alloy has a better corrosion resistance in the artificial saliva and can replace the Ti-Ni alloy in the dental application. In the non-oral condition, the Ti-52Nb alloy may be preferable.

The Microstructure and Creep Behavior of Cold Rolled Udimet 188 Sheet

2010 ◽  
Vol 17 (3) ◽  
pp. 350-361
Author(s):  
C.J. Boehlert ◽  
S.C. Longanbach
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Creep Behavior ◽  
Volume Fraction ◽  
Solution Treatment ◽  
Tensile Creep ◽  
Dislocation Creep ◽  
Grain Boundary Character Distribution ◽  
Air Cooling ◽  
Cold Rolled

AbstractUdimet 188 was subjected to thermomechanical processing (TMP) in an attempt to understand the effects of cold-rolling deformation on the microstructure and tensile-creep behavior. Commercially available sheet was cold rolled to varying amounts of deformation (between 5–35% reduction in sheet thickness) followed by a solution treatment at 1,464 K (1,191°C) for 1 h and subsequent air cooling. This sequence was repeated four times to induce a high-volume fraction of low-energy grain boundaries. The resultant microstructure was characterized using electron backscattered diffraction. The effect of the TMP treatment on the high-temperature [1,033–1,088 K (760–815°C)] creep behavior was evaluated. The measured creep stress exponents (6.0–6.8) suggested that dislocation creep was dominant at 1,033 K (760°C) for stresses ranging between 100–220 MPa. For stresses ranging between 25–100 MPa at 1,033 K (760°C), the stress exponents (2.3–2.8) suggested grain boundary sliding was dominant. A significant amount of grain boundary cracking was observed both on the surface and subsurface of deformed samples. To assess the mechanisms of crack nucleation, in situ scanning electron microscopy was performed during the elevated-temperature tensile-creep deformation. Cracking occurred preferentially along general high-angle grain boundaries (GHAB) and less than 25% of the cracks were found on low-angle grain boundaries (LAB) and coincident site lattice boundaries (CSLB). Creep rupture experiments were performed at T = 1,088 K (815°C) and σ = 165 MPa and the greatest average time-to-rupture was exhibited by the TMP sheet with the greatest fraction of LAB+CSLB. However, a clear correlation was not exhibited between the grain boundary character distribution and the minimum creep rates. The findings of this work suggest that although grain boundary engineering may be possible for this alloy, simply relating the fraction of grain boundary types to the creep resistance is not sufficient.

Sign in / Sign up

Export Citation Format

Share Document