Strain Localizations in Ultra Low Carbon Steel

2011 ◽  
Vol 702-703 ◽  
pp. 782-785
Author(s):  
Rajesh Khatirkar ◽  
Karri V. Mani Krishna ◽  
Leo Kestens ◽  
Roumen H. Petrov ◽  
Prita Pant ◽  
...  
Keyword(s):  
Dislocation Density ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Low Carbon ◽  
Dislocation Dynamic ◽  
Dynamic Simulations ◽  
Discrete Dislocation ◽  
Resolution Electron ◽  
Different Strains ◽  
Grain Misorientation

Ultra low carbon (ULC) steel samples were deformed in near plane-strain compression mode with different strains, strain rates and temperatures. Different aspects of microstructural developments, for deformed γ (ND//) and θ (ND//) fibre grains, were investigated using X-ray line profiles and high resolution electron diffraction. The study clearly showed increase in grain interior strain localizations and in-grain misorientation at the intermediate deformation temperature. This effect was more apparent in γ-fibre and can best be explained through orientation sensitive recovery. γ-fibre also demonstrated higher potential for increase in dislocation density. This was observed experimentally and simulated through discrete dislocation dynamic simulations. Higher textural softening with stronger increase in dislocation density and possible effects of orientation sensitive recovery appears to define the orientation dependent recovery in low carbon steels.

Lattice Imaging of Twin, Lath and α/Martensite Boundaries in Duplex Low Carbon Steels

1977 ◽  
Vol 35 ◽  
pp. 118-119
Author(s):  
J. Y. Koo ◽  
G. Thomas
Keyword(s):  
High Resolution Electron Microscopy ◽  
Ferrite Matrix ◽  
Carbon Steels ◽  
Bright Field Image ◽  
Low Carbon ◽  
Lattice Imaging ◽  
Bright Field ◽  
Lattice Image ◽  
New Information ◽  
Resolution Electron

High resolution electron microscopy has been shown to give new information on defects(1) and phase transformations in solids (2,3). In a continuing program of lattice fringe imaging of alloys, we have applied this technique to the martensitic transformation in steels in order to characterize the atomic environments near twin, lath and αmartensite boundaries. This paper describes current progress in this program.Figures A and B show lattice image and conventional bright field image of the same area of a duplex Fe/2Si/0.1C steel described elsewhere(4). The microstructure consists of internally twinned martensite (M) embedded in a ferrite matrix (F). Use of the 2-beam tilted illumination technique incorporating a twin reflection produced {110} fringes across the microtwins.

scholarly journals A dislocation density-based model for the work hardening and softening behaviors upon stress reversal

2021 ◽  
Vol 21 (2) ◽  
Author(s):  
Paulina Lisiecka-Graca ◽  
Krzysztof Bzowski ◽  
Janusz Majta ◽  
Krzysztof Muszka
Keyword(s):  
Dislocation Density ◽  
Electron Backscatter Diffraction ◽  
Microstructural Analysis ◽  
Back Stress ◽  
Carbon Steels ◽  
Internal Variables ◽  
Low Carbon ◽  
Average Dislocation Density ◽  
Calculation Results ◽  
Mechanical Behaviours

AbstractThe mechanical behaviours of microalloyed and low-carbon steels under strain reversal were modelled based on the average dislocation density taking into account its allocation between the cell walls and cell interiors. The proposed model reflects the effects of the dislocations displacement, generation of new dislocations and their annihilation during the metal-forming processes. The back stress is assumed as one of the internal variables. The value of the initial dislocation density was calculated using two different computational methods, i.e. the first one based on the dislocation density tensor and the second one based on the strain gradient model. The proposed methods of calculating the dislocation density were subjected to a comparative analysis. For the microstructural analysis, the high-resolution electron backscatter diffraction (EBSD) microscopy was utilized. The calculation results were compared with the results of forward/reverse torsion tests. As a result, good effectiveness of the applied computational methodology was demonstrated. Finally, the analysis of dislocation distributions as an effect of the strain path change was performed.

Effect of Soaking Time on Paste Carburizing of Carburized Low Carbon Steel

2017 ◽  
Vol 740 ◽  
pp. 93-99
Author(s):  
Muhammad Hafizuddin Jumadin ◽  
Bulan Abdullah ◽  
Muhammad Hussain Ismail ◽  
Siti Khadijah Alias ◽  
Samsiah Ahmad
Keyword(s):  
Carbon Steel ◽  
Carbon Content ◽  
Low Carbon Steel ◽  
Case Depth ◽  
Carbon Steels ◽  
Low Carbon ◽  
Soaking Time ◽  
Low Carbon Steels ◽  
Carburized Steel ◽  
Carburizing Process

Increase of soaking time contributed to the effectiveness of case depth formation, hardness properties and carbon content of carburized steel. This paper investigates the effect of different soaking time (7-9 hours) using powder and paste compound to the carburized steel. Low carbon steels were carburized using powder and paste compound for 7, 8 and 9 hours at temperature 1000°C. The transformation of microstructure and formation carbon rich layer was observed under microscope. The microhardness profiles were analyzed to investigate the length of case depth produced after the carburizing process. The increment of carbon content was considered to find the correlation between types of carburizing compound with time. Results shows that the longer carburized steel was soaked, the higher potential in formation of carbon rich layer, case depth and carbon content, which led to better hardness properties for carburized low carbon steel. Longer soaking time, 9 hours has a higher dispersion of carbon up to 41%-51% compare to 8 hours and 7 hours. By using paste carburizing, it has more potential of carbon atom to merge the microstructure to transform into cementite (1.53 wt% C) compare to powder (0.97 wt% C), which increases the hardness of carburized steel (13% higher).

Predicting the Effects of Cold Working on the Machining Characteristics of Low Carbon Steels

1987 ◽  
Vol 109 (3) ◽  
pp. 257-264 ◽  
Author(s):  
E. M. Kopalinsky ◽  
P. L. B. Oxley
Keyword(s):  
Flow Stress ◽  
Carbon Steel ◽  
Cutting Forces ◽  
Cold Working ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Low Carbon ◽  
Low Carbon Steels ◽  
Steel Work ◽  
Machining Characteristics

Experiments show that the cold working of low carbon steel work materials can improve their machinability by reducing cutting forces and improving surface finish and tool life. The somewhat paradoxical result of reducing cutting forces by cold working a material so that its hardness is increased is explained in this paper by using a machining theory which takes account of the flow stress properties of the work material and can thus allow for the effects of cold working.

Effect of Ti, Al and Mg Addition on the Impact Toughness of Heat Affected Zone in Low Carbon Steel

2009 ◽  
Vol 79-82 ◽  
pp. 143-146
Author(s):  
Jiang Hua Ma ◽  
Dong Ping Zhan ◽  
Zhou Hua Jiang ◽  
Ji Cheng He
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Low Carbon Steel ◽  
Optical Microscope ◽  
Carbon Steels ◽  
Low Carbon ◽  
Welding Simulation ◽  
Mg Addition ◽  
The Impact

In order to understand the effects of deoxidizer such as aluminium, titanium and magnesium on the impact toughness of heat affected zone (HAZ), three low carbon steels deoxidized by Ti-Al, Mg and Ti-Mg were obtained. After smelting, forging, rolling and welding simulation, the effects of Al, Ti and Mg addition on the impact toughness of HAZ in low carbon steel were studied. The inclusion characteristics (size, morphology and chemistry) of samples before welding and the fracture pattern of the specimens after the Charpy-type test were respectively analyzed using optical microscope and scanning electron microscopy (SEM). The following results were found. The density of inclusion in Ti-Mg deoxidized steel is bigger than Ti-Al deoxidized steel. The average diameter is decreased for the former than the latter. The addition of Ti-Mg can enhance the impact toughness of the HAZ after welding simulation. The maximal value of the impact toughness is 66.5J/cm2. The complex particles of MgO-TiOx-SiO2-MnS are most benefit to enhance impact toughness. The improvement of HAZ is attributable to the role of particle pinning and the formation of intergranular ferrite.

High Temperature Corrosion of Al Hot-Dipped Low Carbon Steels in N2/H2S-Mixed Gases

2016 ◽  
Vol 369 ◽  
pp. 59-64
Author(s):  
Muhammad Ali Abro ◽  
Dong Bok Lee
Keyword(s):  
High Temperature ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Alloy Layer ◽  
High Temperature Corrosion ◽  
Carbon Steels ◽  
Low Carbon ◽  
Mixed Gas ◽  
Low Carbon Steels ◽  
Mixed Gases

A low carbon steel was hot-dip aluminized, and corroded in the N2/0.4%H2S-mixed gas at 650-850°C for 20-50 h in order to find the effect of aluminizing on the high-temperature corrosion of the low carbon steel in the H2S environment. A thin Al topcoat and a thick Al-Fe alloy layer that consisted primarily of Al5Fe2 and some FeAl and Al3Fe formed on the surface after aluminizing. The corrosion rate increased with an increase in temperature. Hot-dip aluminizing increased the corrosion resistance of the carbon steel through forming a thin protective α-Al2O3 scale on the surface. The α-Al2O3 scale was susceptible to spallation. During corrosion, internal voids formed in the Al-Fe alloy layer, where the Al5Fe2, AlFe, and Al3Fe compounds gradually transformed through interdiffusion.

scholarly journals Cu Precipitation Behaviors and Microscopic Mechanical Characteristics of a Novel Ultra-Low Carbon Steel

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3571
Author(s):  
Mingxue Sun ◽  
Yang Xu ◽  
Tiewei Xu
Keyword(s):  
Cooling Rate ◽  
Young’S Modulus ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Precipitation Strengthening ◽  
Low Carbon ◽  
Cooling Rates ◽  
The Matrix

We studied the effect of Cu addition on the hardness of ultra-low carbon steels heat treated with different cooling rates using thermal simulation techniques. The microstructural evolution, Cu precipitation behaviors, variations of Vickers hardness and nano-hardness are comparatively studied for Cu-free and Cu-bearing steels. The microstructure transforms from ferritic structure to ferritic + bainitic structure as a function of cooling rate for the two steels. Interphase precipitation occurs in association with the formation of ferritic structure at slower cooling rates of 0.05 and 0.2 °C/s. Coarsening of Cu precipitates occurs at 0.05 °C/s, leading to lower precipitation strengthening. As the cooling rate increases to 0.2 °C/s, the interphase and dispersive precipitation strengthening effects are increased by 63.9 and 50.0 MPa, respectively. Cu precipitation is partially constrained at cooling rate of 5 °C/s, resulting in poor nano-hardness and Young’s Modulus. In comparison with Cu-free steel, the peak Vickers hardness, nano-hardness and Young’s Modulus are increased by 56 HV, 0.61 GPa and 55.5 GPa at a cooling rate of 0.2 °C/s, respectively. These values are apparently higher than those of Cu-free steel, indicating that Cu addition in steels can effectively strengthen the matrix.

The Application of 3D-EBSD for Investigating Texture Development in Metals and Alloys

2011 ◽  
Vol 702-703 ◽  
pp. 469-474
Author(s):  
Michael Ferry ◽  
M. Zakaria Quadir ◽  
Nasima Afrin Zinnia ◽  
Lori Bassman ◽  
Cassandra George ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Electron Backscatter Diffraction ◽  
Ion Beam ◽  
Low Carbon Steel ◽  
Texture Development ◽  
Data Generation ◽  
Low Carbon ◽  
Resolution Electron ◽  
Multi Phase ◽  
Backscatter Diffraction

A focused ion beam (FIB) coupled with high resolution electron backscatter diffraction (EBSD) has emerged as a useful tool for generating crystallographic information in reasonably large volumes of microstructure. In principle, data generation is reasonably straightforward whereby the FIB is used as a high precision serial sectioning device for generating consecutive milled surfaces suitable for mapping by EBSD. However, there are several challenges facing the technique including the need for accurate reconstruction of the EBSD slice data and the development of methods for representing the myriad microstructural features of interest including, for example, orientation gradients arising from plastic deformation through to the structure of grains and their interfaces in both single-phase and multi-phase materials. This paper provides an overview of the use of 3D-EBSD in the study of texture development in alloys during deformation and annealing and includes an update on current research on the crystallographic nature of microbands in some body centred and face centred cubic alloys and the nucleation and growth of grains in an extra low carbon steel.

Oriented Nucleation and Selective Growth during Secondary Recrystallization in Ultra Low Carbon Steels

2004 ◽  
Vol 467-470 ◽  
pp. 941-948 ◽  
Author(s):  
Kim Verbeken ◽  
Leo Kestens
Keyword(s):  
Grain Growth ◽  
Texture Evolution ◽  
Secondary Recrystallization ◽  
Low Carbon Steel ◽  
Primary Recrystallization ◽  
Carbon Steels ◽  
Abnormal Grain Growth ◽  
Selective Growth ◽  
Low Carbon ◽  
Ultra Low Carbon Steel

After primary recrystallization, on further annealing, abnormal grain growth occurred in ultra low carbon steel. Texture evolution was studied by comparing the orientations after complete secondary recrystallization, with on one hand the nuclei for abnormal grain growth and on the other hand the selective growth products of the primary recrystallized matrix. The influence of both mechanisms could be identified in the final texture.

Deformation and Structure Difference of Steel Droplets during Initial Solidification

2017 ◽  
Vol 36 (4) ◽  
pp. 347-357 ◽  
Author(s):  
Yang Li ◽  
Jing Wang ◽  
Jiaquan Zhang ◽  
Changgui Cheng ◽  
Zhi Zeng
Keyword(s):  
Carbon Steel ◽  
Continuous Casting ◽  
High Carbon Steel ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Solidification Structure ◽  
Low Carbon ◽  
High Carbon ◽  
Peritectic Steel ◽  
Initial Solidification

AbstractThe surface quality of slabs is closely related with the initial solidification at very first seconds of molten steel near meniscus in mold during continuous casting. The solidification, structure, and free deformation for given steels have been investigated in droplet experiments by aid of Laser Scanning Confocal Microscope. It is observed that the appearances of solidified shells for high carbon steels and some hyper-peritectic steels with high carbon content show lamellar, while that for other steels show spherical. Convex is formed along the chilling direction for most steels, besides some occasions that concave is formed for high carbon steel at times. The deformation degree decreases gradually in order of hypo-peritectic steel, ultra-low carbon steel, hyper-peritectic steel, low carbon steel, and high carbon steel, which is consistent with the solidification shrinkage in macroscope during continuous casting. Additionally, the microstructure of solidified shell of hypo-peritectic steel is bainite, while that of hyper-peritectic steel is martensite.

Sign in / Sign up

Export Citation Format

Share Document