Effect of Strontium and T6 Heat Treatment on Structure and Performance of Al-11.6Si-0.5Mg Alloy

2013 ◽  
Vol 749 ◽  
pp. 1-6
Author(s):  
Ji Xing Lin ◽  
Jun Ping Zhang ◽  
Li Yuan Niu ◽  
Da Ren Sun ◽  
Zi Mu Shi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Eutectic Structure ◽  
Air Cooling ◽  
Water Cooling ◽  
T6 Heat Treatment ◽  
Sr Modification ◽  
Economic Process ◽  
And Performance ◽  
Microstructure And Performance

In this study, Strontium (Sr) was added as modifier during the casting of Al-11.6Si-0.5Mg alloy, and the effect of T6 heat treatment on microstructure and performance of alloy was also investigated. The results showed that the 0.3% Al-8%Sr master alloy can refine effectively the α-Al dendrite and eutectic structure; the best economic process of T6 heat treatment is solution at 535°C for 6 hrs., and water cooling at 50~60°C,aging at 160°C for 6 hrs , then air cooling. After Sr modification and T6 heat treatment, the mechanical properties of alloy are improved remarkably, i.e., the tensile strength increased to 348MPa from 183MPa before modification and the elongation raises from 3.0% to 6.5%. So this alloy is applied to the strain clamp products in electric power fitting industry.

scholarly journals Effect of Heat Treatment on the Microstructure and Performance of Cu Nanofoams Processed by Dealloying

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2691
Author(s):  
Jenő Gubicza ◽  
Péter Jenei ◽  
Gigap Han ◽  
Pham Tran Hung ◽  
Youngseok Song ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Performance ◽  
High Capacity ◽  
Lithium Ion ◽  
High Specific Surface Area ◽  
Cu Alloy ◽  
And Performance ◽  
Underlying Mechanisms ◽  
Microstructure And Performance

Cu nanofoams are promising materials for a variety of applications, including anodes in high-performance lithium-ion batteries. The high specific surface area of these materials supports a high capacity and porous structure that helps accommodate volume expansion which occurs as batteries are charged. One of the most efficient methods to produce Cu nanofoams is the dealloying of Cu alloy precursors. This process often yields nanofoams that have low strength, thus requiring additional heat treatment to improve the mechanical properties of Cu foams. This paper provides the effects of heat treatment on the microstructures, mechanical properties, and electrochemical performance of Cu nanofoams. Annealing was conducted under both inert and oxidizing atmospheres. These studies ultimately reveal the underlying mechanisms of ligament coarsening during heat treatment.

Effect of Mg, Sr, Ti and Aging Parameters on the Mechanical Behavior of 319 Alloys in the T5 and T6 Heat Treatment

2012 ◽  
Vol 482-484 ◽  
pp. 2275-2288
Author(s):  
Saleh Alkahtani
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Treatment ◽  
Magnesium Content ◽  
Air Cooling ◽  
Particle Spacing ◽  
Sr Modification ◽  
Heat Treated ◽  
Negative Effect ◽  
Mg Content

In this work, the effect of metallurgical parameters (i.e. alloy chemistry and aging parameters) on the mechanical properties of 319 alloys was investigated, with the aim of adjusting these parameters to produce castings of suitable mechanical properties. An attempt has been made to quantify the effects of alloying elements (Mg, Sr, and Ti) and aging parameters on the mechanical properties of heat-treated (T5 and T6) 319 alloys. Exploring the heat treatment differences between T5 and T6 for 319 alloys would help in selecting the metallurgical conditions required to achieve the optimum and maximum mechanical properties. Aging treatments were carried out for 319 alloys in the T5- and T6-condition at 150°C, 180°C, 200°C, 220°C and 250°C for 4, 8, 16, 24 and 48 h, followed by air cooling. Aging treatment at a lower temperature of 150°C produces fine and dense precipitates having a smaller inter-particle spacing, while at higher aging temperatures, such as 250°C, the precipitates are coarser in size, less dense, and more widely dispersed. For 319 alloys, crack initiate and propagate mainly through the debonding of Si particles from the Al matrix and through the cleavage of β-iron intermetallics. Fracture of intermetallic phases in the interdendritic regions is mostly brittle, with the formation of microcracks at the Si, Cu, Fe-base intermetallics and aluminium interfaces. Experimental correlations of the results obtained from the mechanical properties measurements are analyzed and correlations that relate the alloying additions and heat treatment to the ultimate tensile strength (UTS), yield strength (YS) and total percent elongation (%E) of such alloys are found. Different levels of magnesium content (%Mg), Sr-modification (Sr-ppm), aging parameters (temperature and time) were tested. The effect of alloy additions (Mg, Sr and Ti) and aging heat treatment parameters (Temperature and Time) on the mechanical properties and alloy performance of cast and heat treated 319 alloys are investigated. It was found that the strength of 319 alloys increases with the magnesium content and decreases with the Sr-modification (Sr-ppm) and aging parameters (temperature and time). Increasing the Mg content in primary 319 alloys up to 0.45% enhances the alloy response to heat treatment in the T5 and T6 Tempers, more particularly, the T6 one. Sr-Modification of high Mg content 319 alloy in amounts of ~360 ppm leads to a noticeable decline in alloy strength due to porosity formation which counteracts the beneficial effect of the modification. Sr-modification has a negative effect on the % elongation results of Mg-content 319 alloys due to the Mg-Sr interaction in the aged-T6 conditions. However, grain refining of the Mg and Sr content 319 alloys produce sounder castings with finer grain sizes

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

scholarly journals Study on the Effect of High-Temperature Heat Treatment on the Microscopic Pore Structure and Mechanical Properties of Tight Sandstone

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Liangbin Dou ◽  
Guanli Shu ◽  
Hui Gao ◽  
Jinqing Bao ◽  
Rui Wang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Pore Structure ◽  
Water Cooling ◽  
Tight Sandstone ◽  
The Core ◽  
Core Samples ◽  
High Temperature Heat Treatment ◽  
Different Temperatures ◽  
Cooling Methods

The investigation of changes in physical properties, mechanical properties, and microscopic pore structure characteristics of tight sandstone after high-temperature heat treatment provides a theoretical basis for plugging removal and stimulation techniques, such as high energy gas fracturing and explosive fracturing. In this study, core samples, taken from tight sandstone reservoirs of the Yanchang Formation in the Ordos Basin, were first heated to different temperatures (25-800°C) and then cooled separately by two distinct cooling methods—synthetic formation water cooling and natural cooling. The variations of wave velocity, permeability, tensile strength, uniaxial compressive strength, and microscopic pore structure of the core samples were analyzed. Experimental results demonstrate that, with the rise of heat treatment temperature, the wave velocity and tensile strength of tight sandstone decrease nonlinearly, yet its permeability increases nonlinearly. The tight sandstone’s peak strength and elastic modulus exhibit a trend of the first climbing and then declining sharply with increasing temperature. After being treated by heat at different temperatures, the number of small pores varies little, but the number of large pores increases obviously. Compared to natural cooling, the values of physical and mechanical properties of core samples treated by synthetic formation water cooling are apparently smaller, whereas the size and number of pores are greater. It can be explained that water cooling brings about a dramatic reduction of tight sandstone’s surface temperature, generating additional thermal stress and intensifying internal damage to the core. For different cooling methods, the higher the core temperature before cooling, the greater the thermal stress and the degree of damage caused during the cooling process. By taking into consideration of changes in physical properties, mechanical properties, and microscopic pore structure characteristics, the threshold temperature of tight sandstone is estimated in the range of 400-600°C.

Residual Stress Analysis Considering Phase Transformation and Transformation Plasticity for Heat-Treated Large Size Shaft

2016 ◽  
Vol 725 ◽  
pp. 647-652 ◽  
Author(s):  
Yusuke Yanagisawa ◽  
Yasuhiro Kishi ◽  
Katsuhiko Sasaki
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Phase Transformation ◽  
Air Cooling ◽  
Water Cooling ◽  
Stress Distributions ◽  
Transformation Plasticity ◽  
Large Size ◽  
Heat Treated ◽  
Good Agreement

The residual stress distributions of the forgings after both water-cooling and air-cooling were measured experimentally. The residual stress occurring during the heat-treatment was also simulated considering the phase transformation and the transformation plasticity. A comparison of the experiments with the simulations showed a good agreement. These results shows that the transformation plastic strain plays an important role in the heat treatment of large forged shafts.

The Effect of Heat Treatment on Microstructure and Performance of Die Forging Copper

2013 ◽  
Vol 690-693 ◽  
pp. 58-61
Author(s):  
Gui Rong Yang ◽  
Wen Ming Song ◽  
Ying Ma ◽  
Yuan Hao
Keyword(s):  
Heat Treatment ◽  
Dislocation Density ◽  
Electric Conductivity ◽  
Annealing Treatment ◽  
Technical Parameter ◽  
Copper Specimen ◽  
Die Forging ◽  
And Performance ◽  
Equiaxed Grain ◽  
Microstructure And Performance

The copper specimen was fabricated through liquid die forging under optimum technical parameter, and the die forging copper was annealed under different conditions. The effect of annealing treatment on the microstructure, strength, hardness and electric conductivity of die forging copper was investigated. The results show that the microstructure of die forging copper was changed into equiaxed grain when the treating temperature was less than 250 °C and treating time was less than 2.0 h. The restoration and recrystallization happened during treatment and the obtained crystal grain size became smaller. The strength of die forging copper decreased after annealing treatment owing to the decreasing of dislocation density and concentration of supersaturated vacancy. The hardness of die forging copper also dropped to some extent. The electric conductivity of die forging copper was increased by 5.2% after annealing treatment because the concentration of supersaturated vacancy and dislocation density was decreased obviously.

New Results of the Heat-Treated CuZn39Pb3 Brass Behavior and Resistance to Cavitation Erosion

2021 ◽  
Vol 890 ◽  
pp. 173-180
Author(s):  
Ilare Bordeaşu ◽  
Nicușor Alin Sîrbu ◽  
Iosif Lazăr ◽  
Ion Mitelea ◽  
Cristian Ghera ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Cavitation Erosion ◽  
Stress Relief ◽  
Air Cooling ◽  
Water Cooling ◽  
Characteristic Parameters ◽  
Volume Heat ◽  
Heat Treated ◽  
Hardness Increase

The paper presents the results of the behavior and resistance to the erosion by vibrating cavitation of the CuZn39Pb3 brass, obtained by quenching the volume heat treatment from 800°C with water cooling, followed by the stress-relief to 250°C, with air cooling. Comparison with both the delivery status and the naval brass (used for ship propellers), based on the characteristic parameters values, recommended by the ASTM G32 standards and used in the Cavitation Laboratory of the Polytechnic University of Timisoara, shows that the hardness increase resulted from the heat treatment led to a significant increase of resistance to vibrating cavitation.

Study on Metallography Test of the Steel SPV490 for Atmospheric Storage Tank After Fire

2016 ◽  
Author(s):  
Zhou Fang ◽  
Weiwei Hu ◽  
Deyu Liu ◽  
Guanghai Li ◽  
Zhe Wang
Keyword(s):  
Mechanical Properties ◽  
Working Conditions ◽  
Storage Tank ◽  
High Strength ◽  
Air Cooling ◽  
Microscopic Structure ◽  
Water Cooling ◽  
Storage Tanks ◽  
Fire Temperature ◽  
Optical Microstructure

The fire process was simulated by the heat treatment to the Steel SPV490 of atmospheric storage tank, thereby obtaining the metal specimens in different fire temperature, holding time, and cooling modes. And as the temperature increases, the microscopic structure of Steel SPV490 changes under different working conditions, which could be shown in optical microstructure pictures after doing the interception, inlay, polishing, finishing to the specimens. The result shows that, the mechanical properties of the Steel SPV490 for storage tank changes as the temperature rising from the microscopic view. Nodulizing of the cementite in pearlite occurs, and the strength decreases when the high strength steel SPV490 of large atmospheric storage tanks under air cooling condition below 700 °C, however, it equivalents to the normalizing process, as the sorbite occurs in the steel, and the strength increases a bit when the temperature is above 900 °C. The water-cooling of steel SPV490 above 900 °C equivalents to the process of quenching. The occurrence of martensitic substantially increases the strength and the brittleness, and the elongation decreases rapidly.

Sign in / Sign up

Export Citation Format

Share Document