Dynamic Simulation of the Meshed Gears Based on ADAMS

2014 ◽  
Vol 800-801 ◽  
pp. 708-711
Author(s):  
Bo Zhu ◽  
Xi Chen ◽  
Liang Zhou
Keyword(s):  
Dynamic Simulation ◽  
Simulation Method ◽  
Mechanical Analysis ◽  
Force Curve ◽  
Effective Dynamic ◽  
Impact Parameters ◽  
Definition Of ◽  
Contact And Impact ◽  
Design And Manufacture ◽  
The Impact

Gears are widely used in engineering machinery. Mechanical analysis of the gears matters more much than motion analysis when they are used in heavy machinery or equipment. Dynamic simulation of the meshed gears is based on the theory of contact and impact concerning with the definition of the impact parameters and the model in ADAMS, so the dynamic simulation process is often complicated. In this paper, an effective dynamic simulation method of meshed gears was proposed by analyzing the physical significance of the impact parameters and the calculation method of the impact, and the force curve of the meshed gears was simulated. This result can provide basis for the design and manufacture of the gear.

Numerical Analysis of Thermal Stratification in Pressurizer Surge Line

2010 ◽  
Author(s):  
Zhanfei Qi ◽  
Xuewu Cao
Keyword(s):  
Numerical Simulation ◽  
Thermal Stratification ◽  
Three Dimensional ◽  
Simulation Method ◽  
Mechanical Analysis ◽  
Piping System ◽  
Original Design ◽  
Pressurized Water ◽  
Surge Line ◽  
The Impact

The thermal stratification is generic to un-isolable piping system in pressurized water reactor (PWR), which is not considered in original design. This effect can finally threaten the integrity of the piping system. The pressurizer surge line is affected by thermal stratification during reactor heat up and shutdown processes particularly. It’s important to investigate and mitigate thermal stratification in the surge line to meet safety requirements. In this paper, the thermal hydraulic analysis and the mechanical analysis using numerical simulation method were conducted to evaluate the impact of thermal stratification in the surge line during reactor heat up processes. The results give the three-dimensional temperature distribution and stress status of the surge line. It indicates that thermal stratification can cause stress concentration in the displacement restricts. The mitigation of thermal stratification was also studied. The numerical simulation of pressurizer surge line can put forward thermal stratification analysis.

PERTANGGUNGJAWABAN KERUGIAN NEGARA DALAM PENGELOLAAN KEUANGAN DAERAH

EDUKASI ◽  
2018 ◽  
Vol 16 (1) ◽  
Author(s):  
Hendra Karianga
Keyword(s):  
Financial Management ◽  
Criminal Liability ◽  
The State ◽  
Legal Proceedings ◽  
Regional Finance ◽  
Regional Budget ◽  
State Finance ◽  
Budget Policy ◽  
Definition Of ◽  
The Impact

Sources of revenue and expenditure of APBD (regional budget) can be allocated to finance the compulsory affairs and optional affairs in the form of programs and activities related to the improvement of public services, job creation, poverty alleviation, improvement of environmental quality, and regional economic growth. The implications of these policies is the need for funds to finance the implementation of the functions, that have become regional authority, is also increasing. In practice, regional financial management still poses a complicated issue because the regional head are reluctant to release pro-people regional budget policy, even implication of regional autonomy is likely to give birth to little kings in region causing losses to state finance and most end up in legal proceedings. This paper discusses the loss of state finance and forms of liability for losses to the state finance. The result of the study can be concluded firstly,  there are still many differences in giving meaning and definition of the loss of state finace and no standard definition of state losses, can cause difficulties. The difficulty there is in an effort to determine the amount of the state finance losses. The calculation of state/regions losses that occur today is simply assessing the suitability of the size of the budget and expenditure without considering profits earned by the community and the impact of the use of budget to the community. Secondly, the liability for losses to the state finance is the fulfillment of the consequences for a person to give or to do something in the regional financial management by giving birth to three forms of liability, namely the Criminal liability, Civil liability, and Administrative liability.Keywords: state finance losses, liability, regional finance.

Empowering Women Entrepreneurs Through Microfinance - A Case of Rural Bangladesh

2017 ◽  
Vol 3 (2) ◽  
pp. 7
Author(s):  
Saida Parvin
Keyword(s):  
Women's Empowerment ◽  
Assessment Tools ◽  
Women’S Empowerment ◽  
Case Study Method ◽  
Policy Makers ◽  
Theoretical Contribution ◽  
Donor Agencies ◽  
Definition Of ◽  
The Impact

Women’s empowerment has been at the centre of research focus for many decades. Extant literature examined the process, outcome and various challenges. Some claimed substantial success, while others contradicted with evidence of failure. But the success remains a matter of debate due to lack of empirical evidence of actual empowerment of women around the world. The current study aimed to address this gap by taking a case study method. The study critically evaluates 20 cases carefully sampled to include representatives from the entire country of Bangladesh. The study demonstrates popular beliefs about microfinance often misguide even the borrowers and they start living in a fabricated feeling of empowerment, facing real challenges to achieve true empowerment in their lives. The impact of this finding is twofold; firstly there is a theoretical contribution, where the definition of women’s empowerment is proposed to be revisited considering findings from these cases. And lastly, the policy makers at governmental and non-governmental organisations, and multinational donor agencies need to revise their assessment tools for funding.

Stochastic simulation for determining the design flood of cascade reservoir systems

2012 ◽  
Vol 43 (1-2) ◽  
pp. 54-63 ◽  
Author(s):  
Baohong Lu ◽  
Huanghe Gu ◽  
Ziyin Xie ◽  
Jiufu Liu ◽  
Lejun Ma ◽  
...  
Keyword(s):  
Simulation Model ◽  
Stochastic Simulation ◽  
Southern China ◽  
Flow Simulation ◽  
Simulation Method ◽  
Simulation Approach ◽  
Design Flood ◽  
Design Values ◽  
Stochastic Simulation Model ◽  
The Impact

Stochastic simulation is widely applied for estimating the design flood of various hydrosystems. The design flood at a reservoir site should consider the impact of upstream reservoirs, along with any development of hydropower. This paper investigates and applies a stochastic simulation approach for determining the design flood of a complex cascade of reservoirs in the Longtan watershed, southern China. The magnitude of the design flood when the impact of the upstream reservoirs is considered is less than that without considering them. In particular, the stochastic simulation model takes into account both systematic and historical flood records. As the reliability of the frequency analysis increases with more representative samples, it is desirable to incorporate historical flood records, if available, into the stochastic simulation model. This study shows that the design values from the stochastic simulation method with historical flood records are higher than those without historical flood records. The paper demonstrates the advantages of adopting a stochastic flow simulation approach to address design-flood-related issues for a complex cascade reservoir system.

scholarly journals Erosion Transportation Processes as Influenced by Gully Land Consolidation Projects in Highly Managed Small Watersheds in the Loess Hilly–Gully Region, China

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1540
Author(s):  
Qianqian Ji ◽  
Zhe Gao ◽  
Xingyao Li ◽  
Jian’en Gao ◽  
Gen’guang Zhang ◽  
...  
Keyword(s):  
Similarity Theory ◽  
Design Method ◽  
Simulation Method ◽  
Practical Significance ◽  
Land Consolidation ◽  
Small Watershed ◽  
Flood Peak ◽  
Erosion Area ◽  
The Impact ◽  
Erosion Environment

The Loess Hilly–Gully region (LHGR) is the most serious soil erosion area in the world. For the small watershed with high management in this area, the scientific problem that has been paid attention to in recent years is the impact of the land consolidation project on the erosion environment in the gully region. In this study, the 3D simulation method of vegetation, eroded sediment and pollutant transport was innovated based on the principles of erosion sediment dynamics and similarity theory, and the impacts of GLCP were analyzed on the erosion environment at different scales. The verification results show that the design method and the scale conversion relationship (geometric scale: λl = 100) were reasonable and could simulate the transport process on the complex underlying surface of a small watershed. Compared with untreated watersheds, a significant change was the current flood peak lagging behind the sediment peak. There were two important critical values of GLCP impact on the erosion environment. The erosion transport in HMSW had no change when the proportion was less than 0.85%, and increased obviously when it was greater than 3.3%. The above results have important theoretical and practical significance for watershed simulation and land-use management in HMSW.

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

Defining Preterm Birth and Stillbirth in the Western Pacific: A Systematic Review

2021 ◽  
pp. 101053952110260
Author(s):  
Mairead Connolly ◽  
Laura Phung ◽  
Elise Farrington ◽  
Michelle J. L. Scoullar ◽  
Alyce N. Wilson ◽  
...  
Keyword(s):  
Preterm Birth ◽  
National Level ◽  
Health Indicators ◽  
Western Pacific ◽  
World Health ◽  
Middle Income ◽  
Middle Income Countries ◽  
Definition Of ◽  
Health Organization ◽  
The Impact

Preterm birth and stillbirth are important global perinatal health indicators. Definitions of these indicators can differ between countries, affecting comparability of preterm birth and stillbirth rates across countries. This study aimed to document national-level adherence to World Health Organization (WHO) definitions of preterm birth and stillbirth in the WHO Western Pacific region. A systematic search of government health websites and 4 electronic databases was conducted. Any official report or published study describing the national definition of preterm birth or stillbirth published between 2000 and 2020 was eligible for inclusion. A total of 58 data sources from 21 countries were identified. There was considerable variation in how preterm birth and stillbirth was defined across the region. The most frequently used lower gestational age threshold for viability of preterm birth was 28 weeks gestation (range 20-28 weeks), and stillbirth was most frequently classified from 20 weeks gestation (range 12-28 weeks). High-income countries more frequently used earlier gestational ages for preterm birth and stillbirth compared with low- to middle-income countries. The findings highlight the importance of clear, standardized, internationally comparable definitions for perinatal indicators. Further research is needed to determine the impact on regional preterm birth and stillbirth rates.

scholarly journals Equivalent Scalar Stress Formulation Taking into Account Non-Resolved Turbulent Scales

2021 ◽  
Author(s):  
Lucas Konnigk ◽  
Benjamin Torner ◽  
Martin Bruschewski ◽  
Sven Grundmann ◽  
Frank-Hendrik Wurm
Keyword(s):  
Mechanical Stress ◽  
Turbulence Models ◽  
Turbulent Channel Flow ◽  
Simulation Method ◽  
Blood Damage ◽  
Stress Calculation ◽  
High Risk Factors ◽  
Cardiovascular Engineering ◽  
Scalar Stress ◽  
Definition Of

Abstract Purpose Cardiovascular engineering includes flows with fluid-dynamical stresses as a parameter of interest. Mechanical stresses are high-risk factors for blood damage and can be assessed by computational fluid dynamics. By now, it is not described how to calculate an adequate scalar stress out of turbulent flow regimes when the whole share of turbulence is not resolved by the simulation method and how this impacts the stress calculation. Methods We conducted direct numerical simulations (DNS) of test cases (a turbulent channel flow and the FDA nozzle) in order to access all scales of flow movement. After validation of both DNS with literature und experimental data using magnetic resonance imaging, the mechanical stress is calculated as a baseline. Afterwards, same flows are calculated using state-of-the-art turbulence models. The stresses are computed for every result using our definition of an equivalent scalar stress, which includes the influence from respective turbulence model, by using the parameter dissipation. Afterwards, the results are compared with the baseline data. Results The results show a good agreement regarding the computed stress. Even when no turbulence is resolved by the simulation method, the results agree well with DNS data. When the influence of non-resolved motion is neglected in the stress calculation, it is underpredicted in all cases. Conclusion With the used scalar stress formulation, it is possible to include information about the turbulence of the flow into the mechanical stress calculation even when the used simulation method does not resolve any turbulence.

Value assessment of antimicrobials and the implications for development, access, and funding of effective treatments: Australian stakeholder perspective

2020 ◽  
pp. 1-7
Author(s):  
Nadine T. Hillock ◽  
Tracy L. Merlin ◽  
Jonathan Karnon ◽  
John Turnidge ◽  
Jaklin Eliott
Keyword(s):  
Cost Effectiveness ◽  
Healthcare Resource ◽  
Economic Evaluations ◽  
Value Assessment ◽  
Antimicrobial Drugs ◽  
Policy Makers ◽  
Stakeholder Perspective ◽  
Definition Of ◽  
The Impact ◽  
Potential Use

Abstract Background The frameworks used by Health Technology Assessment (HTA) agencies for value assessment of medicines aim to optimize healthcare resource allocation. However, they may not be effective at capturing the value of antimicrobial drugs. Objectives To analyze stakeholder perceptions regarding how antimicrobials are assessed for value for reimbursement purposes and how the Australian HTA framework accommodates the unique attributes of antimicrobials in cost-effectiveness evaluation. Methods Eighteen individuals representing the pharmaceutical industry or policy-makers were interviewed. Interviews were transcribed verbatim, coded, and thematically analyzed. Results Key emergent themes were that reimbursement decision-making should consider the antibiotic spectrum when assessing value, risk of shortages, the impact of procurement processes on low-priced comparators, and the need for methodological transparency when antimicrobials are incorporated into the economic evaluation of other treatments. Conclusions Participants agreed that the current HTA framework for antimicrobial value assessment is inadequate to properly inform funding decisions, as the contemporary definition of cost-effectiveness fails to explicitly incorporate the risk of future resistance. Policy-makers were uncertain about how to incorporate future resistance into economic evaluations without a systematic method to capture costs avoided due to good stewardship. Lacking financial reward for the benefits of narrower-spectrum antimicrobials, companies will likely focus on developing broad-spectrum agents with wider potential use. The perceived risks of shortages have influenced the funding of generic antimicrobials in Australia, with policy-makers suggesting a willingness to pay more for assured supply. Although antibiotics often underpin the effectiveness of other medicines, it is unclear how this is incorporated into economic models.

Sign in / Sign up

Export Citation Format

Share Document