An Innovative Printed Circuit Board Power Delivery Scheme

2011 ◽  
Vol 2011 (1) ◽  
pp. 000069-000072
Author(s):  
Zhenggang Cheng ◽  
Peter Gunadisastra ◽  
Amit Agrawal
Keyword(s):  
Printed Circuit Board ◽  
Cost Effective ◽  
Power Delivery ◽  
Circuit Board ◽  
System Level ◽  
Voltage Regulator ◽  
Printed Circuit ◽  
Noise Simulation ◽  
Power Noise ◽  
Shared Power

In this paper, an innovative board power delivery scheme with two separate power planes merging at VRM (voltage regulator modular) has been studied. The two separate power planes provide power for two different core power rails with the same value. Compared to traditional board power delivery schemes such as two separate power planes with two VRMs or one shared power plane with one VRM, the new power delivery scheme has been found to be cost effective and have good performance for our application by using system level transient power noise simulation and analysis.

In-Plane Electromagnetic Generator Fabricated on Printed Circuit Board Technology

2013 ◽  
Vol 479-480 ◽  
pp. 524-529
Author(s):  
C.T. Pan ◽  
F.T. Hsu ◽  
C.C. Nien ◽  
Z.H. Liu ◽  
Y.J. Chen ◽  
...  
Keyword(s):  
Printed Circuit Board ◽  
Energy Harvester ◽  
Cost Effective ◽  
Circuit Board ◽  
Outer Diameter ◽  
Magnetic Element ◽  
Induced Voltage ◽  
Element Analysis ◽  
Printed Circuit ◽  
Electromagnetic Generator

Small and efficient energy harvesters, as a renewable power supply, draw lots of attention in the last few years. This paper presents a planar rotary electromagnetic generator with copper coils fabricated by using printed circuit board (PCB) as inductance and Nd-Fe-B magnets as magnetic element. Coils are fabricated on PCB, which is presumably cost-effective and promising methods. 28-pole Nd-Fe-B magnets with outer diameter of 50 mm and thickness of 2 mm was sintered and magnetized, which can provide magnetic field of 1.44 Tesla. This harvester consists of planar multilayer with multi-pole coils and multi-pole permanent magnet, and the volume of this harvester is about 50x50x2.5 mm3. Finite element analysis is used to design energy harvesting system, and simulation model of the energy harvester is established. In order to verify the simulation, experiment data are compared with simulation result. The PCB energy harvester prototype can generate induced voltage 0.61 V and 13.29mW output power at rotary speed of 4,000 rpm.

scholarly journals CortiWatch: watch-based cortisol tracker

2019 ◽  
Vol 5 (9) ◽  
pp. FSO416 ◽  
Author(s):  
Paul Rice ◽  
Sayali Upasham ◽  
Badrinath Jagannath ◽  
Roshan Manuel ◽  
Madhavi Pali ◽  
...  
Keyword(s):  
Printed Circuit Board ◽  
Cost Effective ◽  
Circuit Board ◽  
Electrochemical Technique ◽  
Label Free ◽  
Printed Circuit ◽  
Electrochemical Testing ◽  
Testing Techniques ◽  
Small Form Factor ◽  
A Current

Sweat-based analytics have recently caught the attention of researchers and medical professionals alike because they do not require professionally trained personnel or invasive collection techniques to obtain a sample. The following presents a small form-factor biosensor for reporting physiological ranges of cortisol present in ambient sweat (8–151 ng/ml). This device obtains cortisol measurements through low volumes of unstimulated sweat from the user’s wrist. We designed a potentiostatic circuit on a printed circuit board to perform electrochemical testing techniques. The detection modality developed for quantifying sensor response to varying cortisol concentrations is a current based electrochemical technique, chronoamperometry (CA). From the results, the sensor can detect cortisol in the physiologically relevant ranges of cortisol; thus, the sensor is a noninvasive, label free, cost-effective solution for tracking cortisol levels for circadian diagnostics.

scholarly journals Universal synthesis of conductive liquid network in polymers enabling elastic printed circuit board technology

2021 ◽  
Author(s):  
Jiheong Kang ◽  
Wonbeom Lee ◽  
Hyunjun Kim ◽  
Inho Kang ◽  
Hongjun Park ◽  
...  
Keyword(s):  
Liquid Metal ◽  
Acoustic Field ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
System Level ◽  
Large Strains ◽  
Stretchable Electronics ◽  
Electronic Components ◽  
Conductive Liquid ◽  
Printed Circuit

Abstract Stretchable electronics are considered next-generation electronic devices in a broad range of emerging fields, including soft robotics1,2, biomedical devices3,4, human-machine interfaces5,6, and virtual or augmented reality devices7,8. A stretchable printed circuit board (S-PCB) is a basic conductive framework for the facile assembly of system-level stretchable electronics with various electronic components. Since an S-PCB is responsible for electrical communications between numerous electronic components, the conductive lines in S-PCB should strictly satisfy the following features: (i) metallic conductivity, (ii) constant electrical resistance during dynamic stretching, and (iii) tough interface bonding with various components9. Despite recent significant advances in intrinsically stretchable conductors10,11,12, they cannot simultaneously satisfy the above stringent requirements. Here, we present a new concept of conductive liquid network-based elastic conductors. These conductors are based on unprecedented liquid metal particles assembled network (LMPNet) and an elastomer. The unique assembled network structure and reconfigurable nature of the LMPNet conductor enabled high conductivity, high stretchability, tough adhesion, and imperceptible resistance changes under large strains, which enabled the first elastic-PCB (E-PCB) technology. We synthesized LMPNet through an acoustic field-driven cavitation event in the solid state. When an acoustic field is applied, liquid metal nanoparticles (LMPnano) are remarkably generated from original LMPs and assemble into a highly conductive particle network (LMPNet). Finally, we demonstrated a multi-layered E-PCB, in which various electronic components were integrated with tough adhesion to form a highly stretchable health monitoring system. Since our synthesis of LMPNet is universal, we could synthesize LMPNet in various polymers, including hydrogel, self-healing elastomer and photoresist and add new functions to LMPNet.

A Solder Joint Reliability Model for the Philips Lumileds LUXEON Rebel LED Carrier Using Physics of Failure Methodology

2013 ◽  
Vol 2013 (1) ◽  
pp. 000887-000892 ◽  
Author(s):  
Rudi Hechfellner ◽  
Michiel Kruger ◽  
Tewe Heemstra ◽  
Greg Caswell ◽  
Nathan Blattau ◽  
...  
Keyword(s):  
Solder Joint ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Light Emitting Diodes ◽  
Coefficient Of Thermal Expansion ◽  
Thermal Control ◽  
Circuit Board ◽  
System Level ◽  
Light Emitting ◽  
Printed Circuit

Light Emitting Diodes (LEDs) are quickly evolving as the dominant lighting solution for a wide variety of applications. With the elimination of incandescent light bulbs and the toxic limitations of fluorescent bulbs, there has been a dramatic increase in the interest in high-brightness light emitting diodes (HB-LEDs). Getting the light out of the die, with reliable color, while maintaining appropriate thermal control over a long service life is a challenge. These issues must be understood and achieved to meet the needs of unique applications, such as solidstate-lighting, automotive, signage, and medical applications. These applications have requirements for 15–25 years of operation making their reliability of critical importance. The LUXEON Rebel has been accepted as an industry leading LED product, widely used in Mean-Time-Between-Failure (MTBF) sensitive applications. Customers use various mounting platforms, such as FR4 Printed Circuit Board (PCB), FR4 PCB with thermal via's, Aluminum & Copper Metal Core printed Circuit Boards (MCPCB), Super MCPCB, etc. As in other LEDs, when mounting to a platform where a large Coefficient of Thermal Expansion (CTE) exists between the LED & the PCB, Solder fatigue could become an issue that may affect system level lifetime. In this paper we have examined extreme cases and how a solder joint can impact system level reliability. We have modeled the conditions and formed a means to predict system level reliability. We have compared the prediction modeling with empirical tests for validation of the models. It is vital to understand system level reliability factors to build lighting solutions that match the application and customer expectations. It is impractical to test LEDs and other components for 50k hours ~5 years since the device evolution is much faster than that – on average one LED generation every 12–18 month. Hence we need models and prediction methods …..

Effects of Trace Layers and Joule Heating on the Temperature Distribution of Printed Circuit Boards: A Computational Study

2009 ◽  
Vol 1 (2) ◽  
Author(s):  
M. Baris Dogruoz ◽  
Manoj K. Nagulapally
Keyword(s):  
Joule Heating ◽  
Hot Spots ◽  
Printed Circuit Board ◽  
Computational Study ◽  
Computational Cost ◽  
Circuit Board ◽  
System Level ◽  
Printed Circuit ◽  
System Level Simulation ◽  
Background Mesh

A printed circuit board (PCB) is generally a multilayered board made of dielectric material and several layers of traces and vias. Performing detailed system-level computational fluid dynamics (CFD) simulations of PCBs including meshed trace and via geometries for each of the layers is impractical. In the present approach, the effects of the trace and via geometry are accurately modeled in the physical model by importing electronics computer aided-design data consisting of the trace and via layout of the board and computing locally varying orthotropic conductivity (kx, ky, and kz) on the printed circuit board using a background mesh. The spatially varying orthotropic conductivity is then mapped from the background mesh to the CFD mesh and used in a system-level simulation of the PCB with a minimal increase in the overall computational cost. On the other hand, as PCB component densities increase, the current densities increase thereby leading to regions of hot spots due to Joule heating. Hence, it is essential that the computational heat transfer simulations account for the heating due to the high current carrying traces. In order to accurately model the Joule heating of traces and vias, it is of essence to solve for the conservation of current in each of these traces. In this study, the effects of both trace layer nonhomogeneity and Joule heating are examined on a sample PCB with several components attached to it. The results are then compared with those from the conventional modeling techniques. It is demonstrated that there is considerable difference in the location of the hot spots and temperature values between two different methods.

A Novel Low Cost Package for Radio Frequency Applications

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Sandeep Chaturvedi ◽  
Shiban K. Koul
Keyword(s):  
High Frequency ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Cost Effective ◽  
Circuit Board ◽  
Test Results ◽  
Printed Circuit ◽  
Pcb Manufacturing ◽  
Manufacturing Techniques ◽  
Commercial Applications

Design, fabrication, and test results of a novel 3-layer RF package using a commonly available high frequency laminate are presented in this paper. The developed package can be manufactured using standard multilayer printed circuit board (PCB) manufacturing techniques making it cost effective for commercial applications. The package exhibits excellent RF characteristics up to 6 GHz.

SILVerIn: Systematic Integrity Verification of Printed Circuit Board Using JTAG Infrastructure

2021 ◽  
Vol 17 (3) ◽  
pp. 1-28
Author(s):  
Shubhra Deb Paul ◽  
Swarup Bhunia
Keyword(s):  
Integrated Circuit ◽  
Printed Circuit Board ◽  
Supply Voltage ◽  
Semiconductor Industry ◽  
Electronic System ◽  
Circuit Board ◽  
System Level ◽  
Printed Circuit ◽  
Industry Standard ◽  
Custom Hardware

A printed circuit board (PCB) provides necessary mechanical support to an electronic system and acts as a platform for connecting electronic components. Counterfeiting and in-field tampering of PCBs have become significant security concerns in the semiconductor industry as a result of increasing untrusted entities in the supply chain. These counterfeit components may result in performance degradation, profit reduction, and reputation risk for the manufacturers. While Integrated Circuit (IC) level authentication using physical unclonable functions (PUFs) has been widely investigated, countermeasures at the PCB level are scarce. These approaches either suffer from significant overhead issues, or opportunistic counterfeiters can breach them like clockwork. Besides, they cannot be extended to system-level (both chip and PCB together), and their applications are also limited to a specific purpose (i.e., either counterfeiting or tampering). In this article, we introduce SILVerIn , a novel systematic approach to verify the authenticity of all chips used in a PCB as well as the board for combating attacks such as counterfeiting, cloning, and in-field malicious modifications. We develop this approach by utilizing the existing boundary scan architecture (BSA) of modern ICs and PCBs. As a result, its implementation comes at a negligible (∼0.5%) hardware overhead. SILVerIn  is integrated into a PCB design during the manufacturing phase. We implement our technique on a custom hardware platform consisting of an FPGA and a microcontroller. We incorporate the industry-standard JTAG (Joint Test Action Group) interface to transmit test data into the BSA and perform hands-on measurement of supply current at both chip and PCB levels on 20 boards. We reconstruct these current values to digital signatures that exhibit high uniqueness, robustness, and randomness features. Our approach manifests strong reproducibility of signatures at different supply voltage levels, even with a low-resolution measurement setup. SILVerIn  also demonstrates a high resilience against machine learning-based modeling attacks, with an average prediction accuracy of ∼51%. Finally, we conduct intentional alteration experiments by replacing the on-board FPGA to replicate the scenario of PCB tampering, and the results indicate successful detection of in-field modifications in a PCB.

Sign in / Sign up

Export Citation Format

Share Document