scholarly journals Serat Pelepah Sagu Sebagai Alternatif Pengganti Serat Sintesis Fiberglass

2021 ◽  
Vol 6 (1) ◽  
pp. 14
Author(s):  
Budiawan Sulaeman ◽  
Rakhmawati Natsir
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Glass Fiber ◽  
Fiber Diameter ◽  
Natural Fibers ◽  
Fiber Volume ◽  
Synthetic Fibers ◽  
Matrix Volume ◽  
Naoh Solution

Tujuan penelitian ini untuk menganalisis pengaruh ukuran besar diameter serat pelepah sagu terhadap sifat mekanik kekuatan tarik, menganalisis sifat mekanik tarik material komposit yang diperkuat serat pelepah sagu.Berdasarkan hasil penelitian; (1). Larutan NAoH berpengaruh terhadap kuat Tarik specimen, hal ini ditunjukkan pada 2,5% (NAoH terhadap H2O). Nilai kekuatan tariknya 49,486 N/mm2. (2). Serat pelepah sagu kuat tariknya jauh dibawah serat gelas. (48,435 N/mm2< 323 N/mm2). Hal ini disebabkan rongga yang terdapat di serat sintesis lebih rapat dibanding serat alami. (3). Berdasarkan variabel yang diteliti, kekuatan tarik (Ftu) dengan nilai tertinggi terjadi pada komposit (volume 85% matriks : 15% serat) yaitu sebesar 3,12 beban 11824 N. (4). Kekuatan tarik mengalami kenaikan terhadap peningkatan komposisi volume serat. (5). Spesimen uji yang mengalami regangan dan patah pada titik load yaitu pada komposisi volume 85% matriks : 15% serat sebesar 3,12 MPa dengan regangan sebesar 8% dan modulus young yang terjadi sebesar 38,615  MPa.The purpose of this study was to analyze the effect of the size of the sago frond fiber diameter on the mechanical properties of the tensile strength, to analyze the tensile mechanical properties of the composite material reinforced by sago frond fibers. Based on research results; (1) NaOH solution affects the tensile strength of the specimen. This is shown at 2.5% (NaOH to H2O), the tensile strength value is 49.486 N/mm2. (2) Sago frond fiber has a tensile strength far below the glass fiber (48,435 N/mm2 <323 N/mm2). This is because the cavities in synthetic fibers are denser than natural fibers. (3) Based on the variables studied, the tensile strength (Ftu) with the highest value occurs in the composite (85% matrix volume: 15% fiber), which is 3.12 load 11824 N. (4) Tensile strength increases with the increase in fiber volume composition. (5) The test specimens that experienced a strain and fracture at the load point, namely the composition of volume 85% matrix: 15% fiber was 3.12 MPa with a strain of 8% and the modulus young that occurred was 38.615 MPa.

scholarly journals Evaluation of Composite Material used in the Wings of Typical Airplane based on Stress Analysis

2018 ◽  
Vol 3 (11) ◽  
pp. 37-41
Author(s):  
Tawfeeq W. Mohammed ◽  
Dalmn Yaseen Taha ◽  
Rafal R. Abdul-Ilah
Keyword(s):  
Experimental Data ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Carbon Fiber ◽  
Glass Fiber ◽  
Raw Materials ◽  
Stress Test ◽  
Mechanical Tests ◽  
Bending Stress

This research has focused on the evaluation of raw materials that used in the wings of modern airplane. These materials either would be fiberglass, carbon-fiber or aramid based composites like Kevlar. These common materials have been selected and evaluated depending on experimental data obtained from mechanical tests. These tests include: hardness, tensile strength and bending stress. The tests based on ASTM standards for mechanical properties. The results show increasing in the hardness value of graphite-epoxy by 9% comparing with that of fiberglass and by 18% comparing with that of Kevlar-epoxy. The results also show an increasing in the maximum tensile strength of graphite-epoxy by 2.9 times to that of fiberglass and by 5.5 times to that of Kevlar-epoxy. Furthermore, the results of bending stress test show increasing of the maximum strength of Kevlar-epoxy by 30% comparing to that of glass fiber and by 75% comparing to that of graphite-epoxy.

scholarly journals Development and Testing of Pine Apple and Glass Fiber Reinforced Epoxy Hybrid Composites

2019 ◽  
Vol 8 (3) ◽  
pp. 2450-2453
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Fiber Reinforced ◽  
Synthetic Fibers ◽  
Glass Fiber Reinforced

Usage of Natural Fiber Composites (NFC) is increased rapidly due to the bio degradability nature of the fibers. These natural fibers are mixed with synthetic fibers to obtain better mechanical properties. In this study, pine apple and glass fiber reinforced epoxy composites are developed and their mechanical properties were evaluated. Composites were prepared by varying the fibers content and by using hand layup process with glass moulds of size 160 x 160 x 3 mm3 . The obtained laminates were sliced as per the ASTM criterion to test the properties. Higher glass fiber content in the composite specimen obtained higher mechanical properties. The composites can be utilized for the purpose of manufacturing components like doors panels, desks, roof tops etc.

scholarly journals Variation of the Mechanical Properties for Natural Fiber Reinforced Composites with Different Weight Ratio of Ziziphus Nummularia’s (Ber) Fibers

2020 ◽  
Vol 8 (6) ◽  
pp. 5393-5397
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Young Modulus ◽  
Fiber Volume

In the present era, Natural fibers are favored for the formation of composites due to their low density, high strength, biodegradability, easy production, low carbon foot, environment friendly nature in comparison of synthetic fibers. This Paper deals with NFRC made from natural fibers obtained from the plants of arid region of Western Rajasthan on which a few researchers are focusing. This paper discuss on the extraction process of fiber from the ber’s stems, manufacturing of composites by using epoxy resin & ber’s fibers then testing of its mechanical properties e.g. tensile strength, young modulus, yield strength , and percentage elongation. Six Sample were made having weight ratio - 0.1, 0.2, 0.3, 0.4, 0.45, & 0. 6. Dog bone samples were prepared according to the ASTM D638 (Type IV) standard. Tensile strength varies from 12.19 MPa to 25 MPa, while young modulus varies from 1.4GPa to 2.9GPa for different weight ratios. Yield strength varies from 10.77 MPa to 21.16 MPa. Percentage of Elongation varies from 1 to 3%. These results shows that ber’s stems can be used for fiber extraction to manufacture composites materials & for better mechanical properties minimum fiber volume fraction percentage is 13% and maximum fiber fraction is 31%.This data can be used further when optimum value of fiber volume fraction is required to form composites from ber’s fibers.

Manufacturing Technique and Property Evaluation of Cotton/Polyester/ Rubber Composite Warp Knit

2012 ◽  
Vol 627 ◽  
pp. 302-306
Author(s):  
Jia Horng Lin ◽  
Shih Yu Huang ◽  
Hui Yu Yang ◽  
Ching Wen Lin ◽  
Jin Mao Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibers ◽  
Air Permeability ◽  
Cotton Yarn ◽  
Knitted Fabrics ◽  
Synthetic Fibers ◽  
Property Evaluation ◽  
Rubber Composite ◽  
Tearing Strength

Cotton fiber is a type of natural fibers. Using natural fibers to fabricate textile can not only decrease the consumption of synthetic fibers, but also reduce the environmental pollution. This study aims to fabricate elastic knitted fabrics and evaluate their properties. Polyester (PET) filaments and rubber threads serve as the warp while cotton yarn serves as the weft for warp knitting. A crochet machine makes the warp and weft into warp knits with desirable stretchability, during which the amount (single/double) and the ply number (1-, 2-, and 3-ply) of the weft are further varied. The resulting warp knits are evaluated for water absorption, air permeability, and mechanical properties. As demonstrated by the experimental results, the warp knits with single 1-ply weft (S1) yield an optimal air permeability of 224.6 cm3/cm2/s and stiffness along the warp direction of 4.74cm. The warp knits with single 2-ply weft (S2) display an optimal tearing strength of 86N while the warp knits with double 3-ply weft (D3/3) has an optimal tensile strength of 708N.

Effect of Fiber Parameters on the Mechanical Properties of Banana-Glass Fiber Hybrid Composites

2014 ◽  
Vol 592-594 ◽  
pp. 202-205
Author(s):  
V. Santhanam ◽  
M. Chandrasekaran ◽  
N. Venkateshwaran
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Length ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Synthetic Fiber

Composite materials are widely used for their superior properties such as high strength to weight ratio, high tensile strength, low thermal expansion, low density etc. Due to environmental issues the eco-friendly composites are being explored. Natural fibers as reinforcement for polymer composites are widely studied. But natural fibers lack better mechanical properties when compared with synthetic fibers. Hence mixing the natural fiber with a synthetic fiber such as glass fiber will improve mechanical properties of the composites. In this study banana fiber is mixed with glass fiber, and the mixture is used as reinforcement in epoxy matrix. The composite specimens were prepared using hand layup technique, the fibers were randomly oriented. Further the fiber length was varied as 10, 15, 20 and 25mm and volume fraction as 10%, 15%, 20% and 25%. Experiments were conducted to find the effect of fiber length and volume fraction on tensile strength, flexural strength, water absorption properties of the composites. It is observed that a fiber length of 20mm and 20% fiber volume fraction gave better mechanical properties.

scholarly journals Pengaruh prosentase larutan NaOH pada proses alkalisasi serat kulit pohon waru (hibiscus tiliaceus) sebagai reinforcement komposit terhadap kekuatan tarik serat tunggal

2020 ◽  
Vol 8 (2) ◽  
Author(s):  
Arief Rizki Fadhillah ◽  
Dadang Hermawan ◽  
Arie Restu Wardhani
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Composite Materials ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Single Fiber ◽  
Environmental Friendly ◽  
Synthetic Resins ◽  
Naoh Solution ◽  
Naoh Treatment

The utilization of natural fiber, nowadays, has employed as reinforcement of composite materials. Natural fiber can benefit the composite material because of the characters of fibre which is more environmental friendly, economics, lighter and stronger. There are many natural fibers that can be used as reinforcement of composite materials such as the bark fibers of Hibiscus Tiliaceus. Hibiscus Tiliaceus is one species of Hibiscus Tiliaceus that can be found in the mountains in Indonesia. This study aims to determine the tensile strength of a single fiber in Hibiscus Tiliaceus fiber with the additional various percentage of NaOH in the alkalization treatment. The alkalization treatment analyzes the alkali process of NaOH substance by 3%, 6%, 9%, 12%, and without treatment within the bark of Hibiscus Tiliaceus tree. The treatment was undertaken by soaking the NaOH substance in a duration of 120 minutes. After the NaOH solution was immersed, the bark fiber of Hibiscus Tiliaceus was washed with aquades until the solution reaches a pH of 7. The results of this study show the percentage of NaOH solution in the alkaline immersion process affects the tensile strength of a single fiber on Hibiscus Tiliaceus and the process of NaOH solution which has a release of 6% lignin, cellulose, and semilulose content. In addition, the NaOH treatment with a percentage of 6% can be the standard of the process of alkalizing the bark fiber of Hibiscus Tiliaceus which can be used for composite reinforcement. Therefore, 6% of NaOH can affect the bond between the Hibiscus Tiliaceus fibers as reinforcement and synthetic resins as a matrix which can increase the strength of the composite.

scholarly journals Mechanical Properties of Mortars Reinforced with Amazon Rainforest Natural Fibers

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 155
Author(s):  
Régis Pamponet da Fonseca ◽  
Janaíde Cavalcante Rocha ◽  
Malik Cheriaf
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Natural Fibers ◽  
Construction Materials ◽  
Hot Water ◽  
Amazon Rainforest ◽  
Hot Water Treatment ◽  
Composite Binder ◽  
Naoh Solution ◽  
Reference Samples

The addition of natural fibers used as reinforcement has great appeal in the construction materials industry since natural fibers are cheaper, biodegradable, and easily available. In this work, we analyzed the feasibility of using the fibers of piassava, tucum palm, razor grass, and jute from the Amazon rainforest as reinforcement in mortars, exploiting the mechanical properties of compressive and flexural strength of samples with 1.5%, 3.0%, and 4.5% mass addition of the composite binder (50% Portland cement + 40% metakaolin + 10% fly ash). The mortars were reinforced with untreated (natural) and treated (hot water treatment, hornification, 8% NaOH solution, and hybridization) fibers, submitted to two types of curing (submerged in water, and inflated with CO2 in a pressurized autoclave) for 28 days. Mortars without fibers were used as a reference. For the durability study, the samples were submitted to 20 drying/wetting cycles. The fibers improved the flexural strength of the mortars and prevented the abrupt rupture of the samples, in contrast to the fragile behavior of the reference samples. The autoclave cure increased the compressive strength of the piassava and tucum palm samples with 4.5% of fibers.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Sign in / Sign up

Export Citation Format

Share Document