Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

scholarly journals Mechanical Properties of Glass Fiber Concrete with Different Dosages of Glass Fiber

2020 ◽  
Vol 8 (5) ◽  
pp. 3916-3919
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Glass Fibers ◽  
High Dispersion ◽  
Conventional Concrete ◽  
Micro Cracks ◽  
Deformation Properties ◽  
Fiber Concrete

Conventional concrete i.e. the concrete generally has low tensile strength with limited ductility and low resistance towards cracking. The micro cracks that are developed internally are inherent among concrete and can be explained with the help of propagation of that micro cracks due to its inferior tensile strength. Different fibers, added at a certain percentage of concrete known to improve the deformation properties of concrete along with the plasticity against crack resistance, such as flexural strength. Mainly concrete & ferroconcrete research has been moved to steel fibers, and glass fibers have recently become more available, with no corrosion problems associated with glass fibers. This article describes an experimental study of the usage of glass fibers in the structural concrete. High-dispersion CEM-FILL fiberglass of 14 μm diameter with an aspect ratio of 857 was used at a dosage of 0.33% to 1% by weight in concrete and its mechanical properties such as compressive strength, flexural strength and modulus of elasticity.

scholarly journals Mechanical Properties of Composites Reinforced with Textile

2020 ◽  
Vol 57 (1) ◽  
pp. 21-27
Author(s):  
Oana Dodun ◽  
Laurentiu Slatineanu ◽  
Gheorghe Nagit ◽  
Marian Mares ◽  
Adelina Hrituc ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mathematical Model ◽  
Tensile Strength ◽  
Glass Fiber ◽  
Glass Fibers ◽  
Biodegradable Materials ◽  
The Matrix ◽  
Fiber Reinforcements ◽  
Polymer Type ◽  
Properties Of Composites

The needs of environmental protection led to the introduction of composites based on the use of plastics reinforced with biodegradable materials or other easily accessible materials. The overall purpose of the research was to experimentally investigate the possibilities of using some accessible reinforcement materials. Textile based on plants fibers and glass fibers were used as reinforcement materials, while the matrix was a polymer type material. An empirical mathematical model was proposed to highlight the effect of the number of glass fiber reinforcements on the tensile strength. The determined mathematical empirical model and graphical representations highlight how the number of glass fiber reinforcements affects the modulus of elasticity of the composite materials.

Utilization of Flax Fibers and Glass Fibers in a Bio-Based Resin

2014 ◽  
Author(s):  
Nassibeh Hosseini ◽  
Chad A. Ulven ◽  
Fardad Azarmi ◽  
Dean C. Webster ◽  
Thomas J. Nelson
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Glass Fibers ◽  
Flax Fiber ◽  
Nanoindentation Test ◽  
Molding Process ◽  
Plant Oil ◽  
Chemical Structures

A novel highly functional plant oil-based polyols, Methoxylated Sucrose Soyate Polyols (MSSP), were cross-linked with isocyanate to formulate MSSP-based polyurethane (PU) thermosets. The degree of cure or conversion was studied using differential scanning calorimetry (DSC). Compression molding process was used to make composite panels out of MSSP-based polyurethane and flax fiber reinforcement of about 50 vol %. The MSSP-based PU resin reinforced with 50 vol % unidirectional E-glass fiber mats was tested as a reference. The composites were cured at 150°C for 60 minutes. Properties of the MSSP-based PU thermosets and its corresponding flax/glass-fiber reinforced thermoset composites were assessed by tensile strength and modulus, flexural strength and modulus, interlaminar shear strength (ILSS), nanoindentation test, and impact strength. Specific tensile modulus and strength of the flax fiber composites were found to compare with those of glass/MSSP-based PU. The glass/MSSP-based PU composite exhibited superior mechanical properties compared to both bio-based and petroleum-based composites used in previous studies. Compared to soybean oil based composites used in previous studies, bio-based composites based on MSSP showed 70 % and 101 % increase in flexural strength and modulus respectively, 102 % and 93 % increase in tensile strength and modulus respectively, and 56 % increase in ILSS. Compared to petroleum-based PU/glass composites used in previous studies, bio-based composites based on MSSP showed 60 % and 40 % increase in flexural strength and modulus respectively, 102 % and 78 % increase in tensile strength and modulus respectively, 50 % increase in ILSS. Higher mechanical properties in MSSP-based PU composites can be attributed to high functionality, rigid and compact chemical structures of MSSP oligomers in polyol resin.

scholarly journals The Mechanical Properties and Damage Evolution of UHPC Reinforced with Glass Fibers and High-Performance Polypropylene Fibers

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2455
Author(s):  
Jiayuan He ◽  
Weizhen Chen ◽  
Boshan Zhang ◽  
Jiangjiang Yu ◽  
Hang Liu
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Damage Evolution ◽  
High Performance ◽  
High Performance Concrete ◽  
Glass Fibers ◽  
Ultra High Performance Concrete ◽  
Concrete Damaged Plasticity ◽  
The Difference ◽  
Experimental Values

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I5, I10 and I20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

scholarly journals Mechanical and Material Properties of Mortar Reinforced with Glass Fiber: An Experimental Study

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 698 ◽  
Author(s):  
Marcin Małek ◽  
Mateusz Jackowski ◽  
Waldemar Łasica ◽  
Marta Kadela ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Glass Fibers ◽  
Progressive Increase ◽  
Split Tensile Strength ◽  
Glass Waste ◽  
Poisson Coefficient ◽  
Recycled Glass ◽  
Setting Times ◽  
The World

The progressive increase in the amount of glass waste produced each year in the world made it necessary to start the search for new recycling methods. This work summarizes the experimental results of the study on mortar samples containing dispersed reinforcement in the form of glass fibers, fully made from melted glass waste (bottles). Mortar mixes were prepared according to a new, laboratory-calculated recipe containing glass fibers, granite as aggregate, polycarboxylate-based deflocculant and Portland cement (52.5 MPa). This experimental work involved three different contents (600, 1200, and 1800 g/m3) of recycled glass fibers. After 28 days, the mechanical properties such as compressive, flexural, and split tensile strength were characterized. Furthermore, the modulus of elasticity and Poisson coefficient were determined. The initial and final setting times, porosity, and pH of the blends were measured. Images of optical microscopy (OM) were taken. The addition of glass fibers improves the properties of mortar. The highest values of mechanical properties were obtained for concrete with the addition of 1800 g/m3 of glass fibers (31.5% increase in compressive strength, 29.9% increase in flexural strength, and 97.6% increase in split tensile strength compared to base sample).

Effect of Cold Deformation and Annealing on Microstructure and Mechanical Properties of 5083 Aluminum Alloy Sheets

2018 ◽  
Vol 913 ◽  
pp. 49-54
Author(s):  
Jian Xin Wu ◽  
Chong Gao ◽  
Rui Yin Huang ◽  
Zhen Shan Liu ◽  
Pi Zhi Zhao
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Rolling Process ◽  
Prolonged Annealing ◽  
5083 Aluminum Alloy ◽  
Research Hotspots

5083 aluminum alloy, due to moderate strength, good thermal conductivity and formability, is an ideal structural material for car production. Influence of cold rolling process on microstructures and mechanical properties of 5083 aluminum alloys is significant and research hotspots. In this paper, cold deformation and annealing processes on grains, tensile properties and anisotropies of 5083 alloy sheets were studied. Results showed that incomplete recrystallization occured on 5083 alloy sheets when annealing temperature was at 300°C. The degree of recrystallization increased slightly with the cold deformation raised from 30% to 50% and varied slightly with prolonged annealing time from 2h to 4h. Furthermore, fully recrystallization occurred on 5083 alloy sheets at the annealing temperature above 320°C. Tensile strength of 5083 alloy sheets reduced significantly when the annealing temperature was raised from 300°C to 320°C, while it varied slightly when the annealing temperature continued to rise to 380°C.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

scholarly journals The impact of cold deformation, annealing temperatures and chemical assays on the mechanical properties of platinum

2010 ◽  
Vol 46 (1) ◽  
pp. 51-57 ◽  
Author(s):  
B. Trumic ◽  
D. Stankovic ◽  
A. Ivanovic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Platinum Metals ◽  
Deformation Degree ◽  
Annealing Temperatures ◽  
Flow Limit ◽  
The Impact ◽  
Constant Deformation

In order to form the necessary data base on platinum and platinum metals, certain tests were carried out on platinum samples of different purity of 99.5%, 99.9% and 99.99%. The degree of cold deformation, annealing temperature and chemical assays were tested as well as their impact on the mechanical properties of platinum. The Vickers hardness (HV) values were determined with different deformation degree, starting from annealing temperatures for platinum of different purity and tensile strength (Rm), flow limit (Rp0,2) and elongation (A) in the function of annealing temperatures and annealing time at a constant deformation degree.

Fabrication and Characterization of E-Glass Fiber Reinforced Unsaturated Polyester Resin Based Composite Materials

2019 ◽  
Vol 24 ◽  
pp. 1-7
Author(s):  
Md. Naimul Islam ◽  
Harun Ar-Rashid ◽  
Farhana Islam ◽  
Nanda Karmaker ◽  
Farjana A. Koly ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Bending Strength ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Tensile Modulus ◽  
Unsaturated Polyester Resin ◽  
Fiber Reinforced ◽  
Bending Modulus

E-glass fiber mat reinforced Unsaturated Polyester Resin (UPR)-based composites were fabricated by conventional hand lay-up technique. The fiber content was varied from 5 to 50% by weight. Mechanical properties (tensile and bending) of the fabricated composites were investigated. The tensile strength (TS) of the 5% and 50% fiber reinforced composites was 32 MPa and 72 MPa, respectively. Similarly, tensile modulus, bending strength and bending modulus of the composites were increased by the increase of fiber loading. Interfacial properties of the composites were investigated by scanning electron microscopy (SEM) and the results revealed that the interfacial bond between fiber and matrix was excellent. Keywords: Unsaturated Polyester Resin, Mechanical Properties, E-glass Fibers, Composites, Polymer.

Sign in / Sign up

Export Citation Format

Share Document