scholarly journals Laboratory and field studies of ice-nucleating particles from open-lot livestock facilities in Texas

2021 ◽  
Vol 21 (18) ◽  
pp. 14215-14234
Author(s):  
Naruki Hiranuma ◽  
Brent W. Auvermann ◽  
Franco Belosi ◽  
Jack Bush ◽  
Kimberly M. Cory ◽  
...  
Keyword(s):  
Field Survey ◽  
Field Investigation ◽  
Test System ◽  
Ice Nucleation ◽  
High Concentration ◽  
Laboratory Findings ◽  
Two Samples ◽  
Texas Panhandle ◽  
Immersion Freezing ◽  
Dynamic Filter

Abstract. In this work, an abundance of ice-nucleating particles (INPs) from livestock facilities was studied through laboratory measurements from cloud-simulation chamber experiments and field investigation in the Texas Panhandle. Surface materials from two livestock facilities, one in the Texas Panhandle and another from McGregor, Texas, were selected as dust proxies for laboratory analyses. These two samples possessed different chemical and biological properties. A combination of aerosol interaction and dynamics in the atmosphere (AIDA) measurements and offline ice spectrometry was used to assess the immersion freezing mode ice nucleation ability and efficiency of these proxy samples at temperatures above −29 ∘C. A dynamic filter processing chamber was also used to complement the freezing efficiencies of submicron and supermicron particles collected from the AIDA chamber. For the field survey, periodic ambient particle sampling took place at four commercial livestock facilities from July 2017 to July 2019. INP concentrations of collected particles were measured using an offline freezing test system, and the data were acquired for temperatures between −5 and −25 ∘C. Our AIDA laboratory results showed that the freezing spectra of two livestock dust proxies exhibited higher freezing efficiency than previously studied soil dust samples at temperatures below −25 ∘C. Despite their differences in composition, the freezing efficiencies of both proxy livestock dust samples were comparable to each other. Our dynamic filter processing chamber results showed on average approximately 50 % supermicron size dominance in the INPs of both dust proxies. Thus, our laboratory findings suggest the importance of particle size in immersion freezing for these samples and that the size might be a more important factor for immersion freezing of livestock dust than the composition. From a 3-year field survey, we measured a high concentration of ambient INPs of 1171.6 ± 691.6 L−1 (average ± standard error) at −25 ∘C for aerosol particles collected at the downwind edges of livestock facilities. An obvious seasonal variation in INP concentration, peaking in summer, was observed, with the maximum at the same temperature exceeding 10 000 L−1 on 23 July 2018. The observed high INP concentrations suggest that a livestock facility is a substantial source of INPs. The INP concentration values from our field survey showed a strong correlation with measured particulate matter mass concentration, which supports the importance of size in ice nucleation of particles from livestock facilities.

scholarly journals A comprehensive characterization of ice nucleation by three different types of cellulose particles immersed in water

2019 ◽  
Vol 19 (7) ◽  
pp. 4823-4849 ◽  
Author(s):  
Naruki Hiranuma ◽  
Kouji Adachi ◽  
David M. Bell ◽  
Franco Belosi ◽  
Hassan Beydoun ◽  
...  
Keyword(s):  
Aqueous Suspension ◽  
Measurement Techniques ◽  
Active Surface ◽  
Ice Nucleation ◽  
Accuracy And Precision ◽  
Active Surface Site ◽  
Two Samples ◽  
Order Of Magnitude ◽  
Immersion Freezing ◽  
T Values

Abstract. We present the laboratory results of immersion freezing efficiencies of cellulose particles at supercooled temperature (T) conditions. Three types of chemically homogeneous cellulose samples are used as surrogates that represent supermicron and submicron ice-nucleating plant structural polymers. These samples include microcrystalline cellulose (MCC), fibrous cellulose (FC) and nanocrystalline cellulose (NCC). Our immersion freezing dataset includes data from various ice nucleation measurement techniques available at 17 different institutions, including nine dry dispersion and 11 aqueous suspension techniques. With a total of 20 methods, we performed systematic accuracy and precision analysis of measurements from all 20 measurement techniques by evaluating T-binned (1 ∘C) data over a wide T range (−36 ∘C <T<-4 ∘C). Specifically, we intercompared the geometric surface area-based ice nucleation active surface site (INAS) density data derived from our measurements as a function of T, ns,geo(T). Additionally, we also compared the ns,geo(T) values and the freezing spectral slope parameter (Δlog(ns,geo)/ΔT) from our measurements to previous literature results. Results show all three cellulose materials are reasonably ice active. The freezing efficiencies of NCC samples agree reasonably well, whereas the diversity for the other two samples spans ≈ 10 ∘C. Despite given uncertainties within each instrument technique, the overall trend of the ns,geo(T) spectrum traced by the T-binned average of measurements suggests that predominantly supermicron-sized cellulose particles (MCC and FC) generally act as more efficient ice-nucleating particles (INPs) than NCC with about 1 order of magnitude higher ns,geo(T).

scholarly journals Condensation and immersion freezing Ice Nucleating Particle measurements at Ny-Ålesund (Svalbard) during 2018: evidence of multiple source contribution

2020 ◽  
Author(s):  
Matteo Rinaldi ◽  
Naruki Hiranuma ◽  
Gianni Santachiara ◽  
Mauro Mazzola ◽  
Karam Mansour ◽  
...  
Keyword(s):  
Regional Climate ◽  
Arctic Region ◽  
Ground Level ◽  
Test System ◽  
Ice Nucleation ◽  
The Arctic ◽  
Activation Temperature ◽  
Back Trajectories ◽  
Local Sources ◽  
Immersion Freezing

Abstract. The current inadequate understanding of ice nucleating particle (INP) sources in the Arctic region affects the uncertainty in global radiative budgets and in regional climate predictions. In this study, we present atmospheric INP concentrations by offline analyses on samples collected at ground level in Ny-Ålesund (Svalbard), in spring and summer 2018. The ice nucleation properties of the samples were characterized by means of two offline instruments: the Dynamic Filter Processing Chamber (DFPC), detecting condensation freezing INPs, and the West Texas Cryogenic Refrigerator Applied to Freezing Test system (WT-CRAFT), measuring INPs by immersion freezing. Both measurements agreed within an order of magnitude although with some notable offset. INP concentration measured by DFPC ranged 33–185 (median 88), 5–107 (50) and 3–66 (20) m−3, for T = −22, −18 and −15 °C, respectively, while at the same activation temperatures WT-CRAFT measured 3–199 (26), 1–34 (6) and 1–4 (2) m−3, with an offset apparently dependent on the INP activation temperature. This observation may indicate a different sensitivity of Arctic INPs to different ice nucleation modes, even though a contribution from measurement and/or sampling uncertainties cannot be ruled out. An increase in the coarse INP fraction was observed from spring to summer, particularly at the warmest temperature (up to ~ 70 % at −15 °C). This suggests a non-negligible contribution from local sources of biogenic aerosol particles. This conclusion is also supported by the INP temperature spectra, showing ice-forming activity at temperatures higher than −15 °C. Contrary to recent works (e.g., INP measurements from Ny-Ålesund in 2012), our results do not show a sharp spring-to-summer increase of the INP concentration, with distinct behaviors for particles active in different temperature ranges. This likely indicates that the inter-annual variability of conditions affecting the INP emission by local sources may be wider than previously considered and suggests a complex interplay between INP sources. This demonstrate the necessity of further data coverage. Analysis of INP concentrations, active site density, low-travelling back-trajectories (

scholarly journals Mexican agricultural soil dust as a source of ice nucleating particles

2021 ◽  
Author(s):  
Diana L. Pereira ◽  
Irma Gavilán ◽  
Consuelo Letechipía ◽  
Graciela B. Raga ◽  
Teresa Pi Puig ◽  
...  
Keyword(s):  
Agricultural Soil ◽  
Agricultural Sector ◽  
Agricultural Soils ◽  
Ice Nucleation ◽  
Soil Dust ◽  
High Concentration ◽  
Mineralogical Analysis ◽  
Immersion Freezing ◽  
Mixed Phase Clouds

Abstract. Agricultural soil erosion, both mechanical and eolic, may impact cloud processes as some aerosol particles are able to facilitate ice crystals formation. Given the large agricultural sector in Mexico, this study investigates the ice nucleating abilities of agricultural dust collected at different sites and generated in the laboratory. The immersion freezing mechanism of ice nucleation was simulated in the laboratory via the Universidad Nacional Autónoma de México (UNAM)- Micro Orifice Uniform Deposit Impactor (MOUDI)-Droplet freezing technique (DFT) (UNAM-MOUDI-DFT). The results show that agricultural dust from the Mexican territory promote ice formation in a temperature range from −11.8 ºC to −34.5 ºC, with ice nucleating particle (INP) concentrations between 0.11 L−1 and 41.8 L−1. Furthermore, aerosol samples generated in the laboratory are more efficient than those collected in the field, with T50 values (i.e., the temperature at which 50 % of the droplets freeze) higher by more than 2.9 ºC. The mineralogical analysis indicated a high concentration of feldspars i.e., K-feldspar and plagioclase (> 40 %) in most of the aerosol and soil samples, with K-feldspar significantly correlated with the T50 of particles with sizes between 1.8 µm and 3.2 µm. Similarly, the organic carbon (OC) was correlated with the efficiency of aerosol samples from 3.2 µm to 5.6 µm and 1.0 µm to 1.8 µm. Finally, a decrease in the efficiency as INPs, after heating the samples at 300 ºC for 2 h, evidenced that the organic matter from agricultural soils can influence the role of INPs in mixed-phase clouds.

Ice nucleation activity of iron oxides via immersion freezing and an examination of the high ice nucleation activity of FeO

2021 ◽  
Vol 23 (5) ◽  
pp. 3565-3573
Author(s):  
Esther Chong ◽  
Katherine E. Marak ◽  
Yang Li ◽  
Miriam Arak Freedman
Keyword(s):  
Iron Oxides ◽  
Functional Groups ◽  
Ice Nucleation ◽  
Mechanical Processing ◽  
Immersion Freezing ◽  
Nucleation Activity ◽  
Ice Nucleation Activity

FeO has enhanced ice nucleation activity due to functional groups that are exposed upon mechanical processing.

scholarly journals Ice nucleation efficiency of AgI: review and new insights

2016 ◽  
Author(s):  
Claudia Marcolli ◽  
Baban Nagare ◽  
André Welti ◽  
Ulrike Lohmann
Keyword(s):  
Water Saturation ◽  
Experimental Studies ◽  
Freezing Temperature ◽  
Nucleating Agent ◽  
Companion Paper ◽  
Chem Phys ◽  
Ice Nucleation ◽  
Lattice Match ◽  
Ice Nuclei ◽  
Immersion Freezing

Abstract. AgI is one of the best investigated ice nuclei. It has relevance for the atmosphere since it is used for glaciogenic cloud seeding. Theoretical and experimental studies over the last sixty years provide a complex picture of silver iodide as ice nucleating agent with conflicting and inconsistent results. This review compares experimental ice nucleation studies in order to analyse the factors that influence the ice nucleation ability of AgI. We have performed experiments to compare contact and immersion freezing by AgI. This is one of three papers that describe and analyse contact and immersion freezing experiments with AgI. In Nagare et al. (Nagare, B., Marcolli, C., Stetzer, O., and Lohmann, U.: Comparison of measured and calculated collision efficiencies at low temperatures, Atmos. Chem. Phys., 15, 13759–13776, doi:10.5194/acp-15-13759-2015, 2015) collision efficiencies based on contact freezing experiments with AgI are determined and compared with theoretical formulations. In a companion paper, contact freezing experiments are compared with immersion freezing experiments conducted with AgI, kaolinite, and ATD as ice nuclei. The following picture emerges from this analysis: The ice nucleation ability of AgI seems to be enhanced when the AgI particle is on the surface of a droplet, which is indeed the position that a particle takes when it can freely move in a droplet. Ice nucleation by particles with surfaces exposed to air, depends on water adsorption. AgI surfaces seem to be most efficient as ice nuclei when they are exposed to relative humidity at or even above water saturation. For AgI particles that are totally immersed in water, the freezing temperature increases with increasing AgI surface area. Higher threshold freezing temperature seem to correlate with improved lattice matches as can be seen for AgI-AgCl solid solutions and 3AgI•NH4I•6H2O, which have slightly better lattice matches with ice than AgI and also higher threshold freezing temperatures. However, the effect of a good lattice match is annihilated when the surfaces have charges. Also, the ice nucleation ability seems to decrease during dissolution of AgI particles. This introduces an additional history and time dependence of ice nucleation in cloud chambers with short residence times.

scholarly journals An instrument for quantifying heterogeneous ice nucleation in multiwell plates using infrared emissions to detect freezing

2018 ◽  
Vol 11 (10) ◽  
pp. 5629-5641 ◽  
Author(s):  
Alexander D. Harrison ◽  
Thomas F. Whale ◽  
Rupert Rutledge ◽  
Stephen Lamb ◽  
Mark D. Tarn ◽  
...  
Keyword(s):  
Active Sites ◽  
Freezing Temperature ◽  
Equilibrium Temperature ◽  
Ice Nucleation ◽  
Ir Camera ◽  
Low Concentrations ◽  
Immersion Freezing ◽  
Mixed Phase Clouds ◽  
The City ◽  
Good Agreement

Abstract. Low concentrations of ice-nucleating particles (INPs) are thought to be important for the properties of mixed-phase clouds, but their detection is challenging. Hence, there is a need for instruments where INP concentrations of less than 0.01 L−1 can be routinely and efficiently determined. The use of larger volumes of suspension in drop assays increases the sensitivity of an experiment to rarer INPs or rarer active sites due to the increase in aerosol or surface area of particulates per droplet. Here we describe and characterise the InfraRed-Nucleation by Immersed Particles Instrument (IR-NIPI), a new immersion freezing assay that makes use of IR emissions to determine the freezing temperature of individual 50 µL droplets each contained in a well of a 96-well plate. Using an IR camera allows the temperature of individual aliquots to be monitored. Freezing temperatures are determined by detecting the sharp rise in well temperature associated with the release of heat caused by freezing. In this paper we first present the calibration of the IR temperature measurement, which makes use of the fact that following ice nucleation aliquots of water warm to the ice–liquid equilibrium temperature (i.e. 0 ∘C when water activity is ∼1), which provides a point of calibration for each individual well in each experiment. We then tested the temperature calibration using ∼100 µm chips of K-feldspar, by immersing these chips in 1 µL droplets on an established cold stage (µL-NIPI) as well as in 50 µL droplets on IR-NIPI; the results were consistent with one another, indicating no bias in the reported freezing temperature. In addition we present measurements of the efficiency of the mineral dust NX-illite and a sample of atmospheric aerosol collected on a filter in the city of Leeds. NX-illite results are consistent with literature data, and the atmospheric INP concentrations were in good agreement with the results from the µL-NIPI instrument. This demonstrates the utility of this approach, which offers a relatively high throughput of sample analysis and access to low INP concentrations.

scholarly journals Analysis of isothermal and cooling rate dependent immersion freezing by a unifying stochastic ice nucleation model

2015 ◽  
Vol 15 (9) ◽  
pp. 13109-13166
Author(s):  
P. A. Alpert ◽  
D. A. Knopf
Keyword(s):  
Cooling Rate ◽  
Surface Area ◽  
Ice Nucleation ◽  
Rate Dependence ◽  
Nucleation Theory ◽  
Freezing Process ◽  
Nucleation Kinetics ◽  
Rate Dependent ◽  
Immersion Freezing ◽  
The Impact

Abstract. Immersion freezing is an important ice nucleation pathway involved in the formation of cirrus and mixed-phase clouds. Laboratory immersion freezing experiments are necessary to determine the range in temperature (T) and relative humidity (RH) at which ice nucleation occurs and to quantify the associated nucleation kinetics. Typically, isothermal (applying a constant temperature) and cooling rate dependent immersion freezing experiments are conducted. In these experiments it is usually assumed that the droplets containing ice nuclei (IN) all have the same IN surface area (ISA), however the validity of this assumption or the impact it may have on analysis and interpretation of the experimental data is rarely questioned. A stochastic immersion freezing model based on first principles of statistics is presented, which accounts for variable ISA per droplet and uses physically observable parameters including the total number of droplets (Ntot) and the heterogeneous ice nucleation rate coefficient, Jhet(T). This model is applied to address if (i) a time and ISA dependent stochastic immersion freezing process can explain laboratory immersion freezing data for different experimental methods and (ii) the assumption that all droplets contain identical ISA is a valid conjecture with subsequent consequences for analysis and interpretation of immersion freezing. The simple stochastic model can reproduce the observed time and surface area dependence in immersion freezing experiments for a variety of methods such as: droplets on a cold-stage exposed to air or surrounded by an oil matrix, wind and acoustically levitated droplets, droplets in a continuous flow diffusion chamber (CFDC), the Leipzig aerosol cloud interaction simulator (LACIS), and the aerosol interaction and dynamics in the atmosphere (AIDA) cloud chamber. Observed time dependent isothermal frozen fractions exhibiting non-exponential behavior with time can be readily explained by this model considering varying ISA. An apparent cooling rate dependence ofJhet is explained by assuming identical ISA in each droplet. When accounting for ISA variability, the cooling rate dependence of ice nucleation kinetics vanishes as expected from classical nucleation theory. The model simulations allow for a quantitative experimental uncertainty analysis for parameters Ntot, T, RH, and the ISA variability. In an idealized cloud parcel model applying variability in ISAs for each droplet, the model predicts enhanced immersion freezing temperatures and greater ice crystal production compared to a case when ISAs are uniform in each droplet. The implications of our results for experimental analysis and interpretation of the immersion freezing process are discussed.

scholarly journals Integrating laboratory and field data to quantify the immersion freezing ice nucleation activity of mineral dust particles

2015 ◽  
Vol 15 (1) ◽  
pp. 393-409 ◽  
Author(s):  
P. J. DeMott ◽  
A. J. Prenni ◽  
G. R. McMeeking ◽  
R. C. Sullivan ◽  
M. D. Petters ◽  
...  
Keyword(s):  
Mineral Dust ◽  
Order Approximation ◽  
Ice Nucleation ◽  
Calibration Factor ◽  
Dust Particles ◽  
Single Type ◽  
Aerosol Layer ◽  
Atmospheric Measurements ◽  
Immersion Freezing ◽  
Nucleation Activity

Abstract. Data from both laboratory studies and atmospheric measurements are used to develop an empirical parameterization for the immersion freezing activity of natural mineral dust particles. Measurements made with the Colorado State University (CSU) continuous flow diffusion chamber (CFDC) when processing mineral dust aerosols at a nominal 105% relative humidity with respect to water (RHw) are taken as a measure of the immersion freezing nucleation activity of particles. Ice active frozen fractions vs. temperature for dusts representative of Saharan and Asian desert sources were consistent with similar measurements in atmospheric dust plumes for a limited set of comparisons available. The parameterization developed follows the form of one suggested previously for atmospheric particles of non-specific composition in quantifying ice nucleating particle concentrations as functions of temperature and the total number concentration of particles larger than 0.5 μm diameter. Such an approach does not explicitly account for surface area and time dependencies for ice nucleation, but sufficiently encapsulates the activation properties for potential use in regional and global modeling simulations, and possible application in developing remote sensing retrievals for ice nucleating particles. A calibration factor is introduced to account for the apparent underestimate (by approximately 3, on average) of the immersion freezing fraction of mineral dust particles for CSU CFDC data processed at an RHw of 105% vs. maximum fractions active at higher RHw. Instrumental factors that affect activation behavior vs. RHw in CFDC instruments remain to be fully explored in future studies. Nevertheless, the use of this calibration factor is supported by comparison to ice activation data obtained for the same aerosols from Aerosol Interactions and Dynamics of the Atmosphere (AIDA) expansion chamber cloud parcel experiments. Further comparison of the new parameterization, including calibration correction, to predictions of the immersion freezing surface active site density parameterization for mineral dust particles, developed separately from AIDA experimental data alone, shows excellent agreement for data collected in a descent through a Saharan aerosol layer. These studies support the utility of laboratory measurements to obtain atmospherically relevant data on the ice nucleation properties of dust and other particle types, and suggest the suitability of considering all mineral dust as a single type of ice nucleating particle as a useful first-order approximation in numerical modeling investigations.

Rheological characterization of asphalt binders treated with bio sealants for pavement preservation

2018 ◽  
Vol 45 (5) ◽  
pp. 407-412
Author(s):  
Debaroti Ghosh ◽  
Mugurel Turos ◽  
Ed Johnson ◽  
Mihai Marasteanu
Keyword(s):  
Rheological Properties ◽  
Asphalt Binder ◽  
Field Investigation ◽  
Asphalt Binders ◽  
Rheological Characterization ◽  
Softening Effect ◽  
Laboratory Findings ◽  
Pavement Preservation ◽  
Performance Grade ◽  
Water Based

Pavement preservation is playing an increasingly significant role in maintaining our aged pavement infrastructure under severe budget constraints. One important component is the use of surface treatments based on application of sealants. Recently, a number of new products, called bio sealants, have been used to treat aging pavement surfaces. The objective of this study is to investigate rheological properties of the binders treated with these materials to understand the mechanism by which they may improve pavement performance. One plain asphalt binder and four types of sealants, two oil-based sealants, one water-based sealant, and one traditional emulsion were used in the experimental work. The results obtained using a dynamic shear rheometer and a bending beam rheometer were used to determine the changes in rheological properties and the change in performance grade. It was observed that the oil-based sealants have a significant softening effect of the control binder compared to the water-based sealants. The transverse cracking histories from field investigation were used to verify the laboratory findings.

scholarly journals Ice nucleation activity of silicates and aluminosilicates in pure water and aqueous solutions – Part 2: Quartz and amorphous silica

2019 ◽  
Vol 19 (9) ◽  
pp. 6035-6058 ◽  
Author(s):  
Anand Kumar ◽  
Claudia Marcolli ◽  
Thomas Peter
Keyword(s):  
Aqueous Solutions ◽  
Amorphous Silica ◽  
Pure Water ◽  
Ice Nucleation ◽  
Water Volume ◽  
Special Focus ◽  
Quartz Surface ◽  
Mineral Surface ◽  
Glass Vial ◽  
Immersion Freezing

Abstract. Divergent ice nucleation (IN) efficiencies of quartz, an important component of atmospheric mineral dust, have been reported in previous studies. We show here that quartz particles obtain their IN activity from milling and that quartz aged in water loses most of its IN efficiency relative to freshly milled quartz. Since most studies so far reported IN activities of commercial quartz dusts that were milled already by the manufacturer, IN active samples prevailed. Also, the quartz surface – much in contrast to that of feldspars – is not prone to ammonia-induced IN enhancement. In detail we investigate the influence of solutes on the IN efficiency of various silica (SiO2) particles (crystalline and amorphous) with special focus on quartz. We performed immersion freezing experiments and relate the observed variability in IN activity to the influence of milling, the aging time and to the exposure conditions since milling. Immersion freezing with silica particles suspended in pure water or aqueous solutions of NH3, (NH4)2SO4, NH4HSO4, Na2SO4 and NaOH, with solute concentrations corresponding to water activities aw=0.9–1.0, were investigated in emulsified droplets by means of differential scanning calorimetry (DSC) and analyzed in terms of the onset temperature of the heterogeneous freezing signal Thet and the heterogeneously frozen water volume fraction Fhet. Quartz particles, which originate from milling coarse samples, show a strong heterogeneous freezing peak in pure water with Thet equal to 247–251 K. This IN activity disappears almost completely after aging for 7 months in pure water in a glass vial. During this time quartz slowly grew by incorporating silicic acid leached from the glass vial. Conversely, the synthesized amorphous silica samples show no discernable heterogeneous freezing signal unless they were milled. This implies that defects provide IN activity to silica surfaces, whereas the IN activity of a natural quartz surface is negligible, when it grew under near-equilibrium conditions. For suspensions containing milled quartz and the solutes (NH4)2SO4, NH4HSO4 or Na2SO4, Thet approximately follows ThetΔawhet(aw), the heterogeneous freezing onset temperatures that obey Δawhet criterion, i.e., ThetΔawhet(aw)=Tmelt(aw+Δawhet) with Δawhet being a constant offset with respect to the ice melting point curve, similar to homogeneous IN. This water-activity-based description is expected to hold when the mineral surface is not altered by the presence of the solutes. On the other hand, we observe a slight enhancement in Fhet in the presence of these solutes, implying that the compliance with the Δawhet criterion does not necessarily imply constant Fhet. In contrast to the sulfates, dilute solutions of NH3 or NaOH (molality ≥5×10-4 mol kg−1) reveal Thet by 3–8 K lower than ThetΔawhet(aw), indicating a significant impact on the mineral surface. The lowering of Thet of quartz suspended in dilute NH3 solutions is opposite to the distinct increase in Thet that we found in emulsion freezing experiments with aluminosilicates, namely feldspars, kaolinite, gibbsite and micas. We ascribe this decrease in IN activity to the increased dissolution of quartz under alkaline conditions. The defects that constitute the active sites appear to be more susceptible to dissolution and therefore disappear first on a dissolving surface.

Sign in / Sign up

Export Citation Format

Share Document