scholarly journals Hydro-meteorological reconstruction and geomorphological impact assessment of the October, 2018 catastrophic flash flood at Sant Llorenç, Mallorca (Spain)

2019 ◽  
Author(s):  
Jorge Lorenzo-Lacruz ◽  
Celso Garcia ◽  
Enrique Morán-Tejeda ◽  
Arnau Amengual ◽  
Víctor Homar ◽  
...  

Abstract. An extraordinary convective rainfall event, unforeseen by most prediction models, generated a devastating flash flood in Sant Llorenç des Cardassar, Mallorca on October 9, 2018. Four people died in the town (13 people died in the entire affected area). The event was reconstructed, implementing an integrated flash flood modelling approach in this small (23.4 km2) and semi-arid ungauged Mediterranean catchment, with a highly nonlinear hydrological response to heavy precipitation, based on three components: (i) generation of radar-derived precipitation estimates during the event; (ii) modelling of an accurate discharge hydrograph yielded by the basin; and (iii) hydraulic simulation of the event and mapping of affected areas. Radar-derived rainfall estimates showed very high agreement with rain gauge data (R2 = 0.98). Modelled flooding extent is in close agreement with the observed extension by Copernicus Emergency Management Service, based on Sentinel-1 imagery, and both far exceed the extension for a 500-year return period flood. Hydraulic simulation showed that water reached a depth of 3 m at some points, and modelled water depths highly correlate (R2 = 0.91) with in-situ after-event measurements. The flash flood eroded and transported woody and abundant sediment debris, changing channel geomorphology. Water velocity greatly increased at bridge locations crossing the river channel, especially at those closer to Sant Llorenç town centre. This study shows how the very low predictability of this type of extreme convective rainfall events and the very short hydrological response times typical of small Mediterranean catchments continue to challenge the implementation of early warning systems, which effectively reduce people's exposure to flash flood risk in the region.

2019 ◽  
Vol 19 (11) ◽  
pp. 2597-2617 ◽  
Author(s):  
Jorge Lorenzo-Lacruz ◽  
Arnau Amengual ◽  
Celso Garcia ◽  
Enrique Morán-Tejeda ◽  
Víctor Homar ◽  
...  

Abstract. An extraordinary convective rainfall event, unforeseen by most numerical weather prediction models, generated a devastating flash flood (305 m3 s−1) in the town of Sant Llorenç des Cardassar, Mallorca, on 9 October 2018. Four people died inside this village, while casualties were up to 13 over the entire affected area. This extreme event has been reconstructed by implementing an integrated flash flood modelling approach in the Ses Planes catchment up to Sant Llorenç (23.4 km2), based on three components: (i) generation of radar-derived precipitation estimates, (ii) modelling of accurate discharge hydrographs yielded by the catchment (using FEST and KLEM models), and (iii) hydraulic simulation of the event and mapping of affected areas (using HEC-RAS). Radar-derived rainfall estimates show very high agreement with rain gauge data (R2=0.98). Modelled flooding extent is in close agreement with the observed extension by the Copernicus Emergency Management Service, based on Sentinel-1 imagery, and both far exceed the extension for a 500-year return period flood. Hydraulic simulation revealed that water reached a depth of 3 m at some points, and modelled water depths highly correlate (R2=0.91) with in situ after-event measurements. The 9 October flash flood eroded and transported woody and abundant sediment debris, changing channel geomorphology. Water velocity greatly increased at bridge locations crossing the river channel, especially at those closer to the Sant Llorenç town centre. This study highlights how the very low predictability of this type of extreme convective rainfall events and the very short hydrological response times typical of small Mediterranean catchments continue to challenge the implementation of early warning systems, which effectively reduce people's exposure to flash flood risk in the region.


2020 ◽  
Author(s):  
Arnau Amengual ◽  
Jorge Lorenzo-Lacruz ◽  
Celso Garcia ◽  
Enrique Morán Tejeda ◽  
Víctor Homar ◽  
...  

<p>An extraordinary convective rainfall event –unforeseen by most numerical weather prediction models– led to a devastating flash flood in the town of Sant Llorenç des Cardassar, eastern Mallorca, on 9th October 2018. Four people died inside the village, while the total death toll was of 13 and economic damages amounted to 91 M€. The observed flooded extension inside the town by the Copernicus Emergency Management Service –based on Sentinel-1 imagery– far exceeded the extension for a 500-year return period flood. This extreme event has been reconstructed by implementing an integrated flood modelling approach over the semi-arid and small-sized Ses Planes basin up to Sant Llorenç (23.4 km²). This procedure is based on three components: (i) generation of high spatial and temporal resolution radar-derived precipitation estimates; (ii) modelling of the hydrologic response based on post-flood peak discharge estimates; and (iii) hydraulic simulation and mapping of the affected areas based on high water marks. Radar-derived rainfall estimates and the simulated flooding extent and water depths highly correlate with observations. The hydraulic simulation has revealed that water reached a depth of 3 m at some points inside Sant Llorenç and that water velocity greatly increased at bridges’ locations close to the town centre. Even if the catastrophic flash flood was not a debris flow, the flood bore eroded enough material to change channel geomorphology. This study also highlights how the concurrence of the very low predictability of this type of extreme convective rainfall events and the very short hydrological response times typical of small Mediterranean catchments still challenges the implementation of early warning systems, which effectively reduce people’s exposure to flash flood risk in the region.</p>


2014 ◽  
Vol 14 (6) ◽  
pp. 1517-1530 ◽  
Author(s):  
T. Turkington ◽  
J. Ettema ◽  
C. J. van Westen ◽  
K. Breinl

Abstract. Debris flows and flash floods are often preceded by intense, convective rainfall. The establishment of reliable rainfall thresholds is an important component for quantitative hazard and risk assessment, and for the development of an early warning system. Traditional empirical thresholds based on peak intensity, duration and antecedent rainfall can be difficult to verify due to the localized character of the rainfall and the absence of weather radar or sufficiently dense rain gauge networks in mountainous regions. However, convective rainfall can be strongly linked to regional atmospheric patterns and profiles. There is potential to employ this in empirical threshold analysis. This work develops a methodology to determine robust thresholds for flash floods and debris flows utilizing regional atmospheric conditions derived from ECMWF ERA-Interim reanalysis data, comparing the results with rain-gauge-derived thresholds. The method includes selecting the appropriate atmospheric indicators, categorizing the potential thresholds, determining and testing the thresholds. The method is tested in the Ubaye Valley in the southern French Alps (548 km2), which is known to have localized convection triggered debris flows and flash floods. This paper shows that instability of the atmosphere and specific humidity at 700 hPa are the most important atmospheric indicators for debris flows and flash floods in the study area. Furthermore, this paper demonstrates that atmospheric reanalysis data are an important asset, and could replace rainfall measurements in empirical exceedance thresholds for debris flows and flash floods.


MAUSAM ◽  
2022 ◽  
Vol 73 (1) ◽  
pp. 91-104
Author(s):  
BIKRAM SINGH ◽  
ROHIT THAPLIYAL

Cloudburst is an extreme weather event characterised by the occurrence of a large amount of rainfall over a small area within a short span of time with a rainfall of 100 mm or more in one hour. It is responsible for flash flood, inundation of low lying areas and landslides in hills causing extensive damages to life and property. During monsoon season 2017 five number of cloudburst events are observed over Uttarakhand and analysed. Self Recording Rain Gauge (SRRG) and 15 minutes interval data from the newly installed General Packet Radio Service (GPRS) based Automatic Weather Station (AWS) are able to capture the cloudburst events over some areas in Uttarakhand. In this paper, an attempt has been made to find out the significant synoptic and thermodynamic conditions associated with the occurrence of the cloudburst events in Uttarakhand. These 5 cases of cloudburst events that are captured during the month of June, July and August 2017 in Uttarakhand are studied in detail. Synoptically, it is observed that the existence of trough at mean sea level from Punjab to head Bay of Bengal running close to Uttarakhand, the movement of Western Disturbance over north Pakistan and adjoining Jammu & Kashmir and existence of cyclonic circulation over north Rajasthan and neighbourhood are favourable conditions. Also, the presence of strong south-westerly wind flow from the Arabian Sea across West Rajasthan and Haryana on upper air charts are found during these events. Thermodynamically, the Convective Available Potential Energy (CAPE) is found to be high (more than 1100 J/Kg) during most of the cases and vertically integrated precipitable water content (PWC) is more than 55mm. The GPRS based AWS system can help in prediction of the cloud burst event over the specified location with a lead time upto half to one hour in association with radar products.  


2011 ◽  
Vol 8 (6) ◽  
pp. 10739-10780
Author(s):  
V. Ruiz-Villanueva ◽  
M. Borga ◽  
D. Zoccatelli ◽  
L. Marchi ◽  
E. Gaume ◽  
...  

Abstract. The 2 June 2008 flood-producing storm on the Starzel river basin in South-West Germany is examined as a prototype for organized convective systems that dominate the upper tail of the precipitation frequency distribution and are likely responsible for the flash flood peaks in this region. The availability of high-resolution rainfall estimates from radar observations and a rain gauge network, together with indirect peak discharge estimates from a detailed post-event survey, provides the opportunity to study the hydrometeorological and hydrological mechanisms associated with this extreme storm and the ensuing flood. Radar-derived rainfall, streamgauge data and indirect estimates of peak discharges are used along with a distributed hydrologic model to reconstruct hydrographs at multiple locations. The influence of storm structure, evolution and motion on the modeled flood hydrograph is examined by using the "spatial moments of catchment rainfall" (Zoccatelli et al., 2011). It is shown that downbasin storm motion had a noticeable impact on flood peak magnitude. Small runoff ratios (less than 20%) characterized the runoff response. The flood response can be reasonably well reproduced with the distributed hydrological model, using high resolution rainfall observations and model parameters calibrated at a river section which includes most of the area impacted by the storm.


2021 ◽  
Vol 13 (21) ◽  
pp. 4243
Author(s):  
Mona Morsy ◽  
Ruhollah Taghizadeh-Mehrjardi ◽  
Silas Michaelides ◽  
Thomas Scholten ◽  
Peter Dietrich ◽  
...  

Water depletion is a growing problem in the world’s arid and semi-arid areas, where groundwater is the primary source of fresh water. Accurate climatic data must be obtained to protect municipal water budgets. Unfortunately, the majority of these arid regions have a sparsely distributed number of rain gauges, which reduces the reliability of the spatio-temporal fields generated. The current research proposes a series of measures to address the problem of data scarcity, in particular regarding in-situ measurements of precipitation. Once the issue of improving the network of ground precipitation measurements is settled, this may pave the way for much-needed hydrological research on topics such as the spatiotemporal distribution of precipitation, flash flood prevention, and soil erosion reduction. In this study, a k-means cluster analysis is used to determine new locations for the rain gauge network at the Eastern side of the Gulf of Suez in Sinai. The clustering procedure adopted is based on integrating a digital elevation model obtained from The Shuttle Radar Topography Mission (SRTM 90 × 90 m) and Integrated Multi-Satellite Retrievals for GPM (IMERG) for four rainy events. This procedure enabled the determination of the potential centroids for three different cluster sizes (3, 6, and 9). Subsequently, each number was tested using the Empirical Cumulative Distribution Function (ECDF) in an effort to determine the optimal one. However, all the tested centroids exhibited gaps in covering the whole range of elevations and precipitation of the test site. The nine centroids with the five existing rain gauges were used as a basis to calculate the error kriging. This procedure enabled decreasing the error by increasing the number of the proposed gauges. The resulting points were tested again by ECDF and this confirmed the optimum of thirty-one suggested additional gauges in covering the whole range of elevations and precipitation records at the study site.


2021 ◽  
Author(s):  
Carol Tamez Melendez ◽  
Judith Meyer ◽  
Audrey Douinot ◽  
Günter Blöschl ◽  
Laurent Pfister

<p>Flash flood events have caused massive damage on multiple occasions between 2016 and 2018 in several catchments in eastern Luxembourg. This region is very well known for being exposed to large-scale winter floods, commonly triggered by long-lasting advective precipitation events related to westerly atmospheric fluxes. However, flash floods - a truly exceptional phenomenon in this region - are have solely occurred in summer in response to intense convective precipitation events. Thus, because of the rare occurrence and local character of this type of events, the mechanisms eventually controlling a flash flood-type response of a catchment remains poorly understood.  </p><p>Here, we focus on four main objectives: i) the role that physiographic characteristics play on the spatial variability of pre-event hydrological states (as expressed via storage) across a set of 41 nested catchments located in the Sûre River basin (4,240 km<sup>2</sup>), Luxembourg, ii) the hydrological response to precipitation controlled by those pre-event hydrological states, iii) the responsivity (resistance) and elasticity (resilience) of the catchments to global change, and iv) the relation between water yields and the offsets from Budyko curve and its related energy limits.</p><p>The area of interest is not only characterised by a homogenous temperate oceanic climate but also by heterogeneous physiographical conditions and land use, which makes it ideal for this study. We used 8 years’ worth hydrological data (precipitation, discharge and potential evapotranspiration) to calculate the increments of the water balance and determine the maximum storage capacity and storage deficits. Second, we used the relationship between storage deficit and discharge to estimate total storage at a hypothetical nearly zero flow condition. Third, we compared the pre-hydrological states and event runoff ratios (Q/P) to the catchments’ physiographical conditions in order to link catchment’s sensitivity to storage metrics. We then assessed the responsivity and elasticity to climate and anthropogenic variations – as expressed through the PET/P and AET/P deviations from the Budyko curve and energy limits– for each individual catchment. Finally, we investigated the catchment’s area control on responsivity, elasticity, water yields and Budyko’s elements across our set of 41 nested catchments.</p>


2014 ◽  
Vol 651-653 ◽  
pp. 1543-1546
Author(s):  
You Shyang Chen

Exploring financial distress activity within a listed target of stock markets focused on creating such prediction models can provide insight into the technological requirements of corporate and the demands placed upon a stock investor in this field. This study integrates professional knowledge to financial ratios into the emerging soft computing techniques for building up a hybrid corporate distress prediction of early warning systems in regarding application fields. Conclusively, the empirical results indicate that the proposed procedure is a great potential alternative of helpful hybrid models to demonstrate its technological merit and application value, and it has increasing the application filings. In terms of managerial implications, the analysis results may be relevant to other types of prediction models seeking to identify financial ratios for the planning processes.


2020 ◽  
Vol 13 (5) ◽  
pp. 92
Author(s):  
Katarina Valaskova ◽  
Pavol Durana ◽  
Peter Adamko ◽  
Jaroslav Jaros

The risk of corporate financial distress negatively affects the operation of the enterprise itself and can change the financial performance of all other partners that come into close or wider contact. To identify these risks, business entities use early warning systems, prediction models, which help identify the level of corporate financial health. Despite the fact that the relevant financial analyses and financial health predictions are crucial to mitigate or eliminate the potential risks of bankruptcy, the modeling of financial health in emerging countries is mostly based on models which were developed in different economic sectors and countries. However, several prediction models have been introduced in emerging countries (also in Slovakia) in the last few years. Thus, the main purpose of the paper is to verify the predictive ability of the bankruptcy models formed in conditions of the Slovak economy in the sector of agriculture. To compare their predictive accuracy the confusion matrix (cross tables) and the receiver operating characteristic curve are used, which allow more detailed analysis than the mere proportion of correct classifications (predictive accuracy). The results indicate that the models developed in the specific economic sector highly outperform the prediction ability of other models either developed in the same country or abroad, usage of which is then questionable considering the issue of prediction accuracy. The research findings confirm that the highest predictive ability of the bankruptcy prediction models is achieved provided that they are used in the same economic conditions and industrial sector in which they were primarily developed.


2020 ◽  
Vol 12 (11) ◽  
pp. 1709 ◽  
Author(s):  
Anna Jurczyk ◽  
Jan Szturc ◽  
Irena Otop ◽  
Katarzyna Ośródka ◽  
Piotr Struzik

A quantitative precipitation estimate (QPE) provides basic information for the modelling of many kinds of hydro-meteorological processes, e.g., as input to rainfall-runoff models for flash flood forecasting. Weather radar observations are crucial in order to meet the requirements, because of their very high temporal and spatial resolution. Other sources of precipitation data, such as telemetric rain gauges and satellite observations, are also included in the QPE. All of the used data are characterized by different temporal and spatial error structures. Therefore, a combination of the data should be based on quality information quantitatively determined for each input to take advantage of a particular source of precipitation measurement. The presented work on multi-source QPE, being implemented as the RainGRS system, has been carried out in the Polish national meteorological and hydrological service for new nowcasting and hydrological platforms in Poland. For each of the three data sources, different quality algorithms have been designed: (i) rain gauge data is quality controlled and, on this basis, spatial interpolation and estimation of quality field is performed, (ii) radar data are quality controlled by RADVOL-QC software that corrects errors identified in the data and characterizes its final quality, (iii) NWC SAF (Satellite Application Facility on support to Nowcasting and Very Short Range Forecasting) products for both visible and infrared channels are combined and the relevant quality field is determined from empirical relationships that are based on analyses of the product performance. Subsequently, the quality-based QPE is generated with a 1-km spatial resolution every 10 minutes (corresponding to radar data). The basis for the combination is a conditional merging technique that is enhanced by involving detailed quality information that is assigned to individual input data. The validation of the RainGRS estimates was performed taking account of season and kind of precipitation.


Sign in / Sign up

Export Citation Format

Share Document