scholarly journals Strength Characteristics of Concrete with Waste Polypropylene as Modifier for Pavement Construction

2021 ◽  
Vol 11 ◽  
pp. 42-50
Author(s):  
Olugbenga Joseph Oyedepo ◽  
Ebenezer Omoniyi Olukanni ◽  
Temitope Rufai Arowolo
Keyword(s):  
Flexural Strength ◽  
Fresh Concrete ◽  
Concrete Pavement ◽  
Polymer Waste ◽  
Coarse Aggregates ◽  
Materials Used ◽  
Pavement Construction ◽  
Flexural Tests ◽  
Waste Polypropylene ◽  
Strength Relationship

The demand for a better performing pavement and the need to convert the ever-growing polymer waste into beneficial use necessitated the need to develop and characterize a polypropylene modified concrete for use in pavement construction. This research focuses on characterizing the strength of concrete produced with waste polypropylene waste as modifiers for pavement construction. The materials used in this research are fine and coarse aggregates, cement and polypropylene waste chairs (PWC). Tests were performed on the aggregate and fresh concrete to determine their suitability and characteristics for use in concrete for pavement. Two concrete grades 1:2:4 and 1:3:6 was produced into 200 mm, 400 mm and 500 mm long paving stones on which compressive and flexural tests were performed. Results obtained showed that 400 mm 1:2:4 grade concrete has the highest compressive strength of 27.36 N/mm2 at 10% polypropylene composition. The 200 mm 1:2:4 concrete grade paving stone with 10% polyprpopylene composition has the highest flexural strength of 12.90 N/mm2. The 200 mm at 10% polypropylene composition correlation coefficient has that the highest value of 0.98 which better explains the compression-flexural strength relationship and validates the 200 mm length at 10% polypropylene composition paving stone as the most adequate length of paving stone for pavement construction. It was concluded that the 200 mm long 1:2:4 concrete grade paving stone at 10% polypropylene composition is the best length of paving stone that can give an adequate flexural strength which is the most important requirent in concrete pavement requirement.

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

Early Age Performance of Continuously Reinforced Concrete Pavement with Different Types of Aggregate

1997 ◽  
Vol 1568 (1) ◽  
pp. 35-43
Author(s):  
Yoon-Ho Cho ◽  
Terry Dossey ◽  
B. Frank Mccullough
Keyword(s):  
Reinforced Concrete ◽  
Field Test ◽  
Field Tests ◽  
Concrete Pavement ◽  
Crack Spacing ◽  
Winter Period ◽  
Thermal Coefficient ◽  
Curing Methods ◽  
Pavement Construction ◽  
New Variables

The effect of coarse aggregate on pavement performance has been attributed to the volume of aggregate used in pavement construction. The different patterns of crack development for limestone (LS) and siliceous river gravel (SRG) are a typical example of aggregate-induced variable performance in continuously reinforced concrete pavement (CRCP). An attempt was made to find a reasonable solution for pavements with SRG. As a way to solve the performance problem observed from the SRG pavement, a blended aggregates mixture was suggested. Laboratory and field tests were performed to check the feasibility of their application in pavements. From the laboratory test, a 50:50 blending ratio was suggested after considering the effect on tensile strength and thermal coefficient of expansion. Field test sections were also constructed to verify previous performance observations for the two aggregates and to provide performance data for new variables such as blended aggregates and special curing methods. Unexpectedly, the blended mixture did not improve the performance of SRG pavement; rather it experienced worse cracking than SRG alone. A controlled experiment with additional field test sections is needed to verify or disprove this finding. The only definitive finding was that selection of aggregate in the concrete pavement is a vital consideration for the design of the pavement. The CRCP8 analytical program reasonably predicted crack spacing for both SRG and LS pavements, predicting mean crack spacing of 0.99 m (3.25 ft) for SRG and 1.98 m (6.41 ft) for the limestone. These values are somewhat below the actual spacing observed at 100 days. Data collected after the first winter period will be required to calibrate the program.

scholarly journals Chemical and Physical Properties of Limestone Powder as a Potential Microfiller of Polymer Composites

2017 ◽  
Vol 63 (2) ◽  
pp. 67-78 ◽  
Author(s):  
M. Kępniak ◽  
P. Woyciechowski ◽  
W. Franus
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Physical Properties ◽  
Polymer Composites ◽  
Asphalt Mixture ◽  
Limestone Powder ◽  
Coarse Aggregates ◽  
Mineral Powder ◽  
Materials Used ◽  
Scanning Electron

Abstract The preliminary stage of asphalt mixture production involves the drying and dedusting of coarse aggregates. The most common types of coarse aggregates used are limestone and basalt. In the process of drying and dedusting the dryer filter accumulates large quantities of waste in the form of mineral powder. This paper introduces an investigation into limestone powder waste as a potential microfiller of polymer composites. Physical characteristics such as the granulation the of powder collected from the filter - in terms of the season of its collection and the type of input materials used - were analysed. A scanning electron microscope (SEM) was used for the investigation described within this paper. The obtained results were compared against those of other materials which can be used as polymer composites microfillers.

Effect of Weld Line Formation on Morphology and Mechanical Properties for 3D-MID Technology

2015 ◽  
Vol 659 ◽  
pp. 659-665
Author(s):  
Supakit Chuaping ◽  
Thomas Mann ◽  
Rapeephun Dangtungee ◽  
Suchart Siengchin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Injection Molding ◽  
Filler Content ◽  
Research Work ◽  
Weld Line ◽  
Processing Conditions ◽  
High Reduction ◽  
Flexural Tests

The topic of this research work was to demonstrate the feasibility of a 3D-MID concept using injection molding technique and investigate the effects of two weld line types on the structure and mechanical properties such as tensile, flexural strength and morphology. In order to obtain more understanding of the bonds between polymer and metals, two different polymer bases of polyphthalamide (PPA) with the same type and amount of filler content were produced by injection molding at the different processing conditions. A mold was designed in such a way that weld and meld line can be produced with different angles by changing as insert inside of the mold. The mechanical properties such as stiffness, tensile strength and flexural strength were determined in tensile and flexural tests, respectively. The results showed in line with the expectation of high reduction on mechanical properties in area where weld/meld lines occurred. The result of tensile test was clearly seen that weld and meld line showed a considerable influence on mechanical properties. The reduction in tensile strength was approximately 58% according to weld line types, whereas in flexural strength was approximately 62%. On the other hand, the effect of the injection times and mold temperatures on the tensile strength were marginal.

Effect of Filler Compositions on the Mechanical Properties of Bamboo Filled Polyester Composite

2014 ◽  
Vol 879 ◽  
pp. 90-95 ◽  
Author(s):  
Abdul Rahman Noor Leha ◽  
Nor Amalina Nordin
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Impact Test ◽  
Compression Molding ◽  
Engineering Applications ◽  
Maximum Value ◽  
Polyester Composite ◽  
Bamboo Powder ◽  
Flexural Tests ◽  
The Impact

Biocomposite from bamboo powder was fabricated by compression molding technique. The objective of this study was to investigate the mechanical properties of bamboo compounded with epoxy with different ratio. Tensile and flexural tests were done to characterize its mechanical properties. It was observed that the strength of bamboo-polyester was increased with increasing amount of bamboo powder. The tensile and flexural strength shows the highest value at 25 wt.% bamboo. However, the impact test shows the maximum value at 20 wt.% bamboo powder. These results exhibit the bamboo-polyester can be a good candidate to be used in many engineering applications

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals 24-hour Fire Produced Effect on Reinforced Recycled Aggregates Concrete Beams

2019 ◽  
Vol 9 (3) ◽  
pp. 4213-4217 ◽  
Author(s):  
A. H. Buller ◽  
M. Oad ◽  
B. A. Memon ◽  
S. Sohu
Keyword(s):  
Flexural Strength ◽  
Concrete Beams ◽  
Testing Machine ◽  
Maximum Load ◽  
Reinforced Concrete Beams ◽  
Recycled Aggregates ◽  
Equal Proportion ◽  
Load Testing ◽  
Coarse Aggregates ◽  
Natural Aggregates

In this article, the effect of prolonged fire (24-hour duration) on reinforced concrete beams made with recycled aggregates from demolished concrete was experimentally investigated. Demolished concrete was used recycled coarse aggregates in equal proportion with natural coarse aggregates. Normal and rich mix concrete with water-cement ratio equal to 0.54 were used. As a control specimen, beams with all-natural aggregates were also cast to compare with the results of the proposed beams. All beams were cured for 28 days and exposed to fire at 1000°C in an oven for 24 hours. After the elapse of this fire period, the beams were allowed to air cool, followed by testing till failure in a universal load testing machine. Comparison of the test results shows that rich mix concrete beams more reduction in flexural strength, more increase in maximum load carrying capacity and deflection than normal mix beams. The maximum reduction in flexural strength was 32.41% for beams cast with 50% RCA and rich mix. Although the fire duration used in this study is rare, yet the outcome provides guidelines for taking proper decisions for retrofitting/strengthening of the fire affected structure before putting it back in service.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Influence of Glass Fibers on Mechanical Properties of Concrete with Recycled Coarse Aggregates

2019 ◽  
Vol 5 (5) ◽  
pp. 1007-1019 ◽  
Author(s):  
Babar Ali ◽  
Liaqat Ali Qureshi ◽  
Ali Raza ◽  
Muhammad Asad Nawaz ◽  
Safi Ur Rehman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Construction Material ◽  
Concrete Compressive Strength ◽  
Coarse Aggregates ◽  
Highly Sensitive

Despite plain cement concrete presenting inferior performance in tension and adverse environmental impacts, it is the most widely used construction material in the world. Consumption of fibers and recycled coarse aggregates (RCA) can add ductility and sustainability to concrete. In this research, two mix series (100%NCA, and 100%RCA) were prepared using four different dosages of GF (0%GF, 0.25%GF, 0.5%GF, and 0.75%GF by volume fraction).  Mechanical properties namely compressive strength, splitting tensile strength, and flexural strength of each concrete mixture was evaluated at the age of 28 days. The results of testing indicated that the addition of GF was very useful in enhancing the split tensile and flexural strength of both RCA and NCA concrete. Compressive strength was not highly sensitive to the addition of GF. The loss in strength that occurred due to the incorporation of RCA was reduced to a large extent upon the inclusion of GF. GF caused significant improvements in the split tensile and flexural strength of RCA concrete. Optimum dosage of GF was determined to be 0.25% for NCA, and 0.5% for RCA concrete respectively, based on the results of combined mechanical performance (MP).

Sign in / Sign up

Export Citation Format

Share Document