scholarly journals Effects of Displacement Velocity on Rock Fracture Shear Strengths under Large Confinements

2016 ◽  
Vol 5 (2) ◽  
pp. 32 ◽  
Author(s):  
Matsee Kleepmek ◽  
Supattra K Hamrat ◽  
Kittitep Fuenkajorn
Keyword(s):  
Rock Fracture ◽  
Shear Velocity ◽  
Confining Pressure ◽  
Displacement Velocity ◽  
Test Results ◽  
Shear Tests ◽  
Confining Pressures ◽  
Strong Rock ◽  
Load Frame ◽  
Induced Fractures

Triaxial shear tests are performed to assess the effects of displacement velocity and confining pressure on shear strengths and dilations of tension-induced fractures and smooth saw-cut surfaces prepared in granite, sandstone and marl specimens. A polyaxial load frame is used to apply confining pressures between 1 and 18 MPa with displacement velocities ranging from 1.15×10-5 to 1.15×10-2 mm/s. The results indicate that the shearing resistances of smooth saw-cut surfaces tend to be independent of the displacement velocity and confining pressure. Under each confinement the peak and residual shear strengths and dilation rates of rough fractures increase with displacement velocities. The sheared-off areas increase when the confining pressure increases, and the displacement rate decreases. The velocity-dependent shear strengths tend to act more under high confining pressures for the rough fractures in strong rock (granite) than for the smoother fractures in weaker rocks (sandstone and marl). An empirical criterion that explicitly incorporates the effects of shear velocity is proposed to describe the peak and residual shear strengths. The criterion fits well to the test results for the three tested rocks.

scholarly journals Research on Microscopic Evolution Laws of Sandstone Deformation and Failure Based on the Particle Discrete Element Method

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhiwei Cai ◽  
Tongqing Wu ◽  
Jian Lu ◽  
Yue Wu ◽  
Nianchun Xu
Keyword(s):  
Shear Crack ◽  
Rock Fracture ◽  
Confining Pressure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Deformation And Failure ◽  
Fracture Development ◽  
Confining Pressures ◽  
The Law ◽  
Microcrack Growth

The fracture of sandstone is closely related to the condition of internal microcracks and the fabric of micrograin. The macroscopic mechanical property depends on its microscopic structures. However, it is difficult to obtain the law of the microcrack growth under loading by experiments. A series of microscopic sandstone models were established with particle flow code 3D (PFC3D) and based on the triaxial experiment results on sandstones. The experimental and numerical simulations of natural and saturated sandstones under different confining pressures were implemented. We analyzed the evolution of rock deformation and the rock fracture development from a microscopic view. Results show that although the sandstones are under different confining pressures, the law of microcrack growth is the same. That is, the number of the microcracks increases slowly in the initial stage and then increases exponentially. The number of shear cracks is more than the tensile cracks, and the proportion of the shear cracks increases with the increase of confining pressure. The cracking strength of natural and saturated sandstones is 26% and 27% of the peak strength, respectively. Under low confining pressure, the total number of cracks in the saturated sample is 20% more than that of the natural sample and the strongly scattered chain is barely seen. With the increase of the confining pressure, the effect of water on the total number of cracks is reduced and the distribution of the strong chain is even more uniform. In other words, it is the confining pressure that mainly affects the distribution of the force chain, irrespective of the state of the rock, natural or saturated. The research results reveal that the control mechanism of shear crack friction under the different stress states of a rock slope in the reservoir area provides a basis for evaluating the stability of rock mass and predicting the occurrence of geological disasters.

Experimental Analysis of Mechanical Properties of High Organic Soft Clay at Different Depths

2014 ◽  
Vol 1056 ◽  
pp. 52-57
Author(s):  
Fei Liu ◽  
Jun Song Chen ◽  
Kai Wen Li
Keyword(s):  
Mechanical Properties ◽  
Northeast China ◽  
Soft Clay ◽  
Confining Pressure ◽  
Test Results ◽  
Shear Tests ◽  
Formation Stage ◽  
Good Guide ◽  
Different Depths ◽  
Clay Layers

In this study, with regard to the differences of formation stage and physicochemical properties for different high organic soft clay layers, a series of laboratory tests have been carried out to evaluate the mechanical properties of high organic soft clay in Northeast China. The conventional high-pressure consolidation and strain-controlled triaxial shear tests have been carried out to measure the compression and shear strength of high organic soft clay which formed in different ages. Furthermore, the comparisons of stress-strain relations between undisturbed and remoulded high organic soft clay samples under the confining pressure of 300kPa reveal the significant differences in compression and shear strengths of high organic soft clay at different depths, which can be interpreted by the differences in the degree of decomposition of the soil. The test results show that the degree of decomposition of high organic soft clay greatly depend on its formation stage at different depths, which is deemed to determine the mechanical properties. This study will provide a good guide to civil engineers on the constructions of the foundation.

scholarly journals Effect of Geotextile Reinforcement on Shear Strength of Sandy Soil: Laboratory Study

2016 ◽  
Vol 38 (4) ◽  
pp. 3-13 ◽  
Author(s):  
Sidali Denine ◽  
Noureddine Della ◽  
Muhammed Rawaz Dlawar ◽  
Feia Sadok ◽  
Jean Canou ◽  
...  
Keyword(s):  
Shear Strength ◽  
Mechanical Behaviour ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Loose Sand ◽  
Test Results ◽  
Compression Tests ◽  
Confining Stress ◽  
Natural Sand ◽  
Confining Pressures

Abstract This paper presents results of a series of undrained monotonic compression tests on loose sand reinforced with geotextile mainly to study the effect of confining stress on the mechanical behaviour of geotextile reinforced sand. The triaxial tests were performed on reconstituted specimens of dry natural sand prepared at loose relative density (Dr = 30%) with and without geotextile layers and consolidated to three levels of confining pressures 50, 100 and 200 kPa, where different numbers and different arrangements of reinforcement layers were placed at different heights of the specimens (0, 1 and 2 layers). The behaviour of test specimens was presented and discussed. Test results showed that geotextile inclusion improves the mechanical behaviour of sand, a significant increase in the shear strength and cohesion value is obtained by adding up layers of reinforcement. Also, the results indicate that the strength ratio is more pronounced for samples which were subjected to low value of confining pressure. The obtained results reveal that high value of confining pressure can restrict the sand shear dilatancy and the more effect of reinforcement efficiently.

scholarly journals Variation in Micro-Pores During Dynamic Consolidation and Compression of Soft Marine Soil

2021 ◽  
Vol 9 (7) ◽  
pp. 750
Author(s):  
Chen-Xiang Dai ◽  
Qiong-Fang Zhang ◽  
Shao-Heng He ◽  
An Zhang ◽  
Hua-Feng Shan ◽  
...  
Keyword(s):  
Cyclic Loading ◽  
Pore Structure ◽  
Dynamic Properties ◽  
Confining Pressure ◽  
Cyclic Stress ◽  
Test Results ◽  
Dynamic Consolidation ◽  
Confining Pressures ◽  
Stress Ratios ◽  
Marine Soil

In this study, to explore the microstructure deformation mechanism of marine soft marine soil under cyclic loading, we analyzed the dynamic properties of soft marine soil under cyclic loading via dynamic consolidation compression testing. Then, using Image-Pro Plus (IPP) 6.0 image analysis software, and according to the dynamic consolidation compression test results and the images from a scanning electron microscope (SEM), we determined the weakening effect of soft soils under different consolidation confining pressures, different cyclic stress ratios, and different over-consolidation ratios. After dynamic consolidation and compression, the pore structure of undisturbed soft marine soil tends to compact, the degree of soil particle fragmentation intensifies, small pores increase, large pores decrease, the pores become more regular, and the distribution of pores is directional. Subsequently, for undisturbed soft marine soil, the higher the consolidated confining pressure, cyclic dynamic stress ratio, and over-consolidation ratio, the greater the damage to the pore structure, and the more obvious the structural weakening effect exhibited under cyclic loading.

scholarly journals Investigating the Permeability of Marble under Moderate Pressure and Temperature

Geofluids ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Jianping Yang ◽  
Weizhong Chen ◽  
Diansen Yang ◽  
Hongming Tian
Keyword(s):  
Volumetric Strain ◽  
Strain Curve ◽  
Confining Pressure ◽  
Crystalline Rock ◽  
Mechanical Tests ◽  
Moderate Pressure ◽  
Test Results ◽  
Permeability Evolution ◽  
Confining Pressures ◽  
Linkage Model

The permeability of intact marble samples collected from the depth of 1.6 km in southwestern China is investigated under moderate confining pressures and temperatures. No microcracks initiate or propagate during the tests, and the variation of permeability is due to the change of aperture of microcracks. Test results show a considerable decrease of permeability along with confining pressure increase from 10 to 30 MPa and temperature increase from 15 to 40°C. The thermal effect on the permeability is notable in comparison with the influence of the stress. A simple permeability evolution law is developed to correlate the permeability and the porosity in the compressive regime based on the microphysical geometric linkage model. Using this law, the permeability in the compressive regime for crystalline rock can be predicted from the volumetric strain curve of mechanical tests.

scholarly journals Effects of granular shape on shear modulus and damping ratio of gravel

2019 ◽  
Vol 23 (1) ◽  
pp. 87-91
Author(s):  
Kai Cui ◽  
Hang Sheng
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Strain Amplitude ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Test Results ◽  
Grain Composition ◽  
Confining Pressures ◽  
Shear Strain Amplitude

The effects of the consolidation ratio, effective confining pressure, gravel content, and granule breakage on the shear modulus and damping ratio of gravel have been extensively researched in recent years. However, studies on the effect of the granular shape are rare. Thus, under different confining pressures, dynamic triaxial tests were performed on gravel specimens to investigate the effect of granular shape on the shear modulus and damping ratio of gravel specimens by using a multifunctional triaxial testing instrument. The samples consisted of two kinds of gravel with the same grain composition and relative density of 45%. The test results indicate that, when the confining pressure and shear strain amplitude exceed 300 kPa and 7×10-4, respectively, gravel with a round granular shape has a higher shear modulus compared to an angular shape. Conversely, when the shear strain amplitude exceeds 2×10-4, the damping ratio of angular gravel exceeds that of round granules.

scholarly journals Experimental SHPB Study of Limestone Damage under Confining Pressures after Exposure to Elevated Temperatures

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1663
Author(s):  
Lei Liu ◽  
Rui Li ◽  
Hao Qin ◽  
Wei Sun
Keyword(s):  
Dynamic Performance ◽  
Mineral Resources ◽  
Confining Pressure ◽  
Dynamic Mechanical Properties ◽  
Temperature Treatment ◽  
High Temperature Treatment ◽  
Test Results ◽  
Low Carbon ◽  
Metallic Mineral ◽  
Confining Pressures

Studying the dynamic performance of rocks affected by high temperatures is a crucial theoretical foundation of mining engineering design and the construction of deep metallic mineral resources. More importantly, such studies can provide technical support for the green and low-carbon mining of these resources. However, systematic studies on the dynamic mechanical properties of rocks affected by both confining pressure and temperature during the mining of deep metallic mineral resources are lacking. Therefore, systematic research was conducted on the dynamic mechanical properties of limestone under confining pressure after high-temperature treatment, and a corresponding constitutive model was established. In this study, limestones were heated to 200 °C, 400 °C, 600 °C, and 800 °C, and the Split Hopkinson Pressure Bar impact test was conducted with confining pressures of 0.0 MPa, 0.5 MPa, 1.5 MPa, and 2.5 MPa. The test results show that the temperature has a significant effect on the dynamic compressive strength of limestone, and as the temperature rises, the strength tends to first increase and then decrease, reaching the turning point at a temperature of 400 °C. The dynamic compressive strength increases as the confining pressure increases. The constitutive equation of the dynamic damage to limestone under confining pressure after high-temperature treatment is consistent with the test results. Therefore, the established constitutive model can represent the dynamic behavior of limestone, providing a reference for evaluating the dynamic performance of this material, and serving as a theoretical basis for the green and low-carbon mining of deep metallic mineral resources.

Reply by the authors to G. H. F. Gardner

Geophysics ◽  
1986 ◽  
Vol 51 (4) ◽  
pp. 1016-1017
Author(s):  
N. I. Christensen ◽  
H. F. Wang
Keyword(s):  
Shear Velocity ◽  
Confining Pressure ◽  
Differential Pressure ◽  
High Porosity ◽  
Inelastic Behavior ◽  
Velocity Measurements ◽  
Pressure Cycle ◽  
Confining Pressures ◽  
Cyclic Variations ◽  
Pressure Changes

Gardner suggests that velocity data in which confining pressure changes are not canceled by equal pore pressure changes may be due to hysteresis effects that prevent velocity from being a unique function of the differential pressure. This is supported by shear velocity measurements in dry Berea sandstone as a function of cyclic variations of differential pressure (Gardner et al., 1965). High porosity and clayey sandstones indeed can demonstrate this behavior. Cyclic pressure variations can lead to work hardening and other inelastic behavior. For our measurements, however, we believe that the effects of hysteresis were minimal because of (1) the pressure cycle followed to obtain velocity as a function of pore and confining pressures, and (2) the large elapsed time between our measurements.

scholarly journals True-Triaxial Drained Test of Tengger Desert Sand

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Xuefeng Li ◽  
Zhigang Ma ◽  
Wennan Lu ◽  
Yandong Wang
Keyword(s):  
Confining Pressure ◽  
Western China ◽  
Test Results ◽  
Tengger Desert ◽  
Stress Strain ◽  
True Triaxial ◽  
Dense Sand ◽  
Desert Sand ◽  
Confining Pressures ◽  
Triaxial Drained Test

For the lack of accurate test results in design and maintenance of desert-crossing highways in the Tengger Desert of western China, the GDS true-triaxial system was used to conduct the drained test on dense sand. Under the condition of different intermediate principal stress ratio b-value, the results showed that the stress-strain relationships in three orthogonal directions had significant differences, presenting significant anisotropy. The peak of the generalized shear stress increased with the increase of b-value. Except under the condition of b = 0, the specimen contracted firstly and then dilated, while the others dilated. The results of the different confining pressures showed that the stress-strain relationships appeared as a hardening type at low confining pressures, and as the confining pressure increased, the stress-strain relationships exhibit hardening, peaking, softening, and stable deformation characteristics. At low confining pressure, the contractive behaviors were not obvious, mainly as dilatancy, and as the confining pressure increased, the dilatancy increased gradually. The specimen transformed contract to dilatancy, and when the confining pressure reached 800 kPa, the specimen exhibited contractive behavior. The test results will provide data for subgrade design and construction in desert area.

scholarly journals Experimental and Numerical Investigation on the Steel Reinforced Grout (SRG) Composite-to-Concrete Bond

2020 ◽  
Vol 4 (4) ◽  
pp. 182
Author(s):  
Luciano Ombres ◽  
Salvatore Verre
Keyword(s):  
Bond Length ◽  
Failure Modes ◽  
Peak Load ◽  
Element Model ◽  
Test Results ◽  
Shear Tests ◽  
Bond Slip ◽  
Bond Behavior ◽  
Direct Shear Tests ◽  
Inorganic Matrix

In the paper, the bond between a composite strengthening system consisting of steel textiles embedded into an inorganic matrix (steel reinforced grout, SRG) and the concrete substrate, is investigated. An experimental investigation was carried out on medium density SRG specimens; direct shear tests were conducted on 20 specimens to analyze the effect of the bond length, and the age of the composite strip on the SRG-to-concrete bond behavior. In particular, the tests were conducted considering five bond length (100, 200, 250, 330, and 450 mm), and the composite strip’s age 14th, 21st, and 28th day after the bonding. Test results in the form of peak load, failure modes and, bond-slip diagrams were presented and discussed. A finite element model developed through commercial software to replicate the behavior of SRG strips, is also proposed. The effectiveness of the proposed numerical model was validated by the comparison between its predictions and experimental results.

Sign in / Sign up

Export Citation Format

Share Document