Surface Treatments of Coffee Husk Fiber Waste for Effective Incorporation into Polymer Biocomposites

Natural lignocellulose fibers have been extensively investigated and applied as a reinforcement of polymer composites in industrial applications from food packing to automotive parts. Among the advantages of natural fibers stands their relatively low cost and sustainable characteristics. These are accentuated in the case of residual fibers such as those obtained from coffee husks, an agribusiness waste, usually burnt or disposed into the environment. As composite reinforcement, hydrophilic natural fibers display adhesion problems to the most hydrophobic polymer matrices. This adhesion might be improved with distinct types of fibers surface treatments. In the present work, the effectiveness of three surface treatments applied to coffee husk fiber wastes (CHFW) were investigated, aiming to improve the tensile performance of castor oil-based polyurethane (COPU) biocomposites. The effects of treatments associated with (i) chemical with sodium hydroxide, (ii) physical by temperature and pressure and hydrothermic treatment, and (iii) biological by fermentation with Phanerochaete Chrysosporium fungus were evaluated by means of Fourier transformed infrared spectroscopy, X-ray diffraction, thermal analyses and morphology by scanning electron microscopy for different concentration of NaOH, different hydrothermic times at 121 °C/98 kPa and exposition to P. chrysosporium. The most effective treatment was the hydrothermal one at 121 °C and 98.06 kPa for 30 min. Preliminary tensile tests were performed in COPU biocomposites reinforced with 20% CHFWs subjected to the optimized conditions for each distinct type of treatment. The results indicated that the hydrothermal treatment promoted significant enhancement in the fiber/matrix interfacial bond, increasing the tensile strength up to 60% compared to COPU reinforced with in natura CHFWs fibers. It is important to mention that these composites can be applied as plastic wood for household items’ internal parts and in the automobile industry.

Evaluation of the Influence of the Conditions of Catalytic Continuous Steam Explosive Activation of Wood on the Physical and Operational Properties of Wooded Composite Materials Based on Activated Fibers

This article presents the results of studies of obtaining wood composite board materials without binders using the method of preliminary steam explosive treatment, as well as an assessment of the impact of impregnation conditions and continuous steam explosive activation of wood on the physical and operational properties of wood-based composite materials based on activated fibers. The rational operating parameters for obtaining board wood-composite materials (WCM) have been determined. We established the influence of impregnation modes (temperature, catalyst concentration), continuous steam explosive treatment with afterwash (temperature, pressure, intensity of mechanical action), as well as the properties of activated lignocellulose fibers (composition and morphological structure) on the operational properties of WCM. The expediency of introducing a catalyst (sodium bisulfite) at the washing stage has been proved, since the introduction of sodium bisulfite during impregnation before steam explosive treatment promotes the formation of lignosulfonates in the activated material, which participate in the formation of the physical properties of WCM.

Enhancement of Interface between Lignocellulosic Fibers and Polypropylene Matrix via the Structure Alteration of Lignin at Elevated Temperatures

This paper investigated the feasibility of enhancing the interface between lignocellulosic fibers and a polypropylene matrix via structure alteration of lignin at elevated temperatures. Alkali treatment can remove gum substances from lignocellulose fibers effectively at elevated temperatures but easily causes damages to fiber strength. In previous studies on directional delignification of lignocellulosic fibers, loss of fiber strength is avoided but condensation and degradation of lignin are accelerated. So far, few reports have been available on the effect of lignin structures on the interface between fibers and a matrix. In this study, jute fibers with different lignin structures are produced at 100 and 130 °C for reinforcing a polypropylene matrix. The interface between the fibers and matrix is analyzed. The result shows that decrease in aliphatic hydroxyl concentration by 9.5% at 130 °C from 3 to 5 h contributes to a 14.2% decrease in the surface energy of jute fibers. Meanwhile, the polydispersity index of lignin decreases from 1.21 to 1.15. Centralized distribution of lignin molecule-weight and reduction in fiber surface energy improves the interface between the fibers and matrix, which manifests as a 30.8% increase in the impact strength of the composites. Similar improvement is not observed in the composites reinforced with jute fibers at 100 °C, due to the absence of lignin-structure changes. This paper provides a new strategy to improve the interface between lignocellulose fibers and a hydrophobic matrix.