Pyroelectric Nanogenerator Based on an SbSI–TiO2 Nanocomposite

For the first time, a composite of ferroelectric antimony sulfoiodide (SbSI) nanowires and non-ferroelectric titanium dioxide (TiO2) nanoparticles was applied as a pyroelectric nanogenerator. SbSI nanowires were fabricated under ultrasonic treatment. Sonochemical synthesis was performed in the presence of TiO2 nanoparticles. The mean lateral dimension da = 68(2) nm and the length La = 2.52(7) µm of the SbSI nanowires were determined. TiO2 nanoparticles served as binders in the synthesized nanocomposite, which allowed for the preparation of dense films via the simple drop-casting method. The SbSI–TiO2 nanocomposite film was sandwiched between gold and indium tin oxide (ITO) electrodes. The Curie temperature of TC = 294(2) K was evaluated and confirmed to be consistent with the data reported in the literature for ferroelectric SbSI. The SbSI–TiO2 device was subjected to periodic thermal fluctuations. The measured pyroelectric signals were highly correlated with the temperature change waveforms. The magnitude of the pyroelectric current was found to be a linear function of the temperature change rate. The high value of the pyroelectric coefficient p = 264(7) nC/(cm2·K) was determined for the SbSI–TiO2 nanocomposite. When the rate of temperature change was equal dT/dt = 62.5 mK/s, the maximum and average surface power densities of the SbSI–TiO2 nanogenerator reached 8.39(2) and 2.57(2) µW/m2, respectively.

Electrical Property Analysis of Textured Ferroelectric Polycrystalline Antimony Sulfoiodide Using Complex Impedance Spectroscopy

Antimony sulfoiodide (SbSI) is a ferroelectric semiconductor with many interesting physical properties (optical, photoconductive, ferroelectric, piezoelectric, etc.). The electrical properties of textured polycrystalline SbSI obtained by the rapid cooling of a melted mass in liquid nitrogen are presented in this work using ac impedance spectroscopy over a wide temperature range (275–500 K) in the frequency range of 1 Hz to 100 kHz. Detailed studies of the impedance Z*(ω), conductivity σ*(ω), electric modulus M*(ω), and dielectric permittivity ε*(ω) of this material were performed using complex impedance spectroscopy for the first time. This study showed that the impedance and related parameters are strongly dependent on temperature. The internal domain structure and the presence of grain boundaries in textured polycrystalline SbSI explain the obtained results.

Ultrasound irradiation mediated preparation of antimony sulfoiodide (SbSI) nanorods as a high-capacity electrode for electrochemical supercapacitors

Antimony sulfoiodide (SbSI) nanorods prepared via a smart ultrasound mediated synthesis route are used as electrode materials towards electrochemical energy storage device applications in both aqueous and ionic liquid-based electrolytes.

Assessment of the Piezoelectric Response of an Epoxy Resin/SbSINanowires Composite Filling FDM Printed Grid

This paper shows a piezoelectric response from an innovative sensor obtained by casting epoxy-SbSI (antimony sulfoiodide) nanowires nanocomposite to a grid structure printed using a fuse deposition modeling (FDM) method. The grid is shown to be a support structure for the nanocomposite. The applied design approach prospectively enables the formation of sensors with a wide spectrum of shapes and a wide applicability. The voltage signal obtained as a result of the piezoelectric effect reached 1.5V and 0.5V under a maximum static stress of 8.5 MPa and under a maximum dynamic stress of 22.3 kPa, respectively. These values are sufficient for potential application in sensor systems. The effect of a systematic increase in the voltage signal with subsequent cycles was also observed, which similarly allows the use of these sensors in monitoring systems for structures exposed to unfavorable cyclical loads. The obtained results also show that the piezoelectric signal improves with increase in strain rate.

Fast and Efficient Piezo/Photocatalytic Removal of Methyl Orange Using SbSI Nanowires

Piezocatalysis is a novel method that can be applied for degradation of organic pollutants in wastewater. In this paper, ferroelectric nanowires of antimony sulfoiodide (SbSI) have been fabricated using a sonochemical method. Methyl orange (MO) was chosen as a typical pollutant, as it is widely used as a dye in industry. An aqueous solution of MO at a concentration of 30 mg/L containing SbSI nanowires (6 g/L) was subjected to ultrasonic vibration. High degradation efficiency of 99.5% was achieved after an extremely short period of ultrasonic irradiation (40 s). The large reaction rate constant of 0.126(8) s−1 was determined for piezocatalytic MO decomposition. This rate constant is two orders of magnitude larger than values of reaction rate constants reported in the literature for the most efficient piezocatalysts. These promising experimental results have proved a great potential of SbSI nanowires for their application in environmental purification and renewable energy conversion.

Defect tolerant zero-bias topological photocurrent in a ferroelectric semiconductor

Lattice defect is a major cause of energy dissipation in conventional electric current due to the drift and diffusion motions of electrons. Different nature of current emerges when noncentrosymmetric materials are excited by light. This current, called the shift current, originates from the change in the Berry connection of electrons’ wave functions during the interband optical transition. Here, we demonstrate the defect tolerance of shift current using single crystals of ferroelectric semiconductor antimony sulfoiodide (SbSI). Although the dark conductance spreads over several orders of magnitude in each crystal due to the difference in the density of defect levels, the observed shift current converges to an identical value. We also reveal that the shift current is scarcely disturbed by the surface defects while they drastically suppress the conventional photocurrent. The defect tolerance is a manifestation of the topological nature of shift current, which will be a crucial advantage in optoelectronic applications.

SbSI Composites Based on Epoxy Resin and Cellulose for Energy Harvesting and Sensors—The Influence of SBSI Nanowires Conglomeration on Piezoelectric Properties

In this paper, ferroelectric antimony sulfoiodide (SbSI) nanowires have been used to produce composites for device fabrication, which can be used for energy harvesting and sensors. SbSI is a very useful material for nanogenerators and nanosensors in which the high values of the piezoelectric coefficient (d33 = 650 pC/N) and the electromechanical coefficient (k33 = 0.9) are essential. Alternatively, cellulose and epoxy resin were matrix materials in these composites, whereas SbSI nanowires fill the matrix. Piezoelectric response induced by vibrations has been presented. Then, a composite with an epoxy resin has been used as an element to construct a fiber-reinforced polymer piezoelectric sensor. For the first time, comparison of piezoelectric properties of cellulose/SbSI and epoxy resin/SbSI nanocomposite has been presented. The influence of concentration of SbSI nanowires for properties of epoxy resin/SbSI nanocomposite and in a fiber-reinforced polymer based on them has also been shown. Results of aligning the SbSI nanowires in the epoxy matrix during a curing process have been presented as well.

A Ferroelectric-Photovoltaic Effect in SbSI Nanowires

A ferroelectric-photovoltaic effect in nanowires of antimony sulfoiodide (SbSI) is presented for the first time. Sonochemically prepared SbSI nanowires have been characterized using high-resolution transmission electron microscopy (HRTEM) and optical diffuse reflection spectroscopy (DRS). The temperature dependences of electrical properties of the fabricated SbSI nanowires have been investigated too. The indirect forbidden energy gap EgIf = 1.862 (1) eV and Curie temperature TC = 291 (2) K of SbSI nanowires have been determined. Aligned SbSI nanowires have been deposited in an electric field between Pt electrodes on alumina substrate. The photoelectrical response of such a prepared ferroelectric-photovoltaic (FE-PV) device can be switched using a poling electric field and depends on light intensity. The photovoltage, generated under λ = 488 nm illumination of Popt = 127 mW/cm2 optical power density, has reached UOC = 0.119 (2) V. The presented SbSI FE-PV device is promising for solar energy harvesting as well as for application in non-volatile memories based on the photovoltaic effect.