Biodiesel production from waste salmon oil: kinetic modeling, properties of methyl esters, and economic feasibility of a low capacity plant

2015 ◽  
Vol 9 (5) ◽  
pp. 516-528 ◽  
Author(s):  
Marta Serrano ◽  
Jorge-Mario Marchetti ◽  
Mercedes Martínez ◽  
José Aracil
Keyword(s):  
Kinetic Modeling ◽  
Methyl Esters ◽  
Economic Feasibility ◽  
Biodiesel Production

Mango (Magnifera indica) seed oil grown in Dilla town as potential raw material for biodiesel production using NaOH- a homogeneous catalyst

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Seed Oil ◽  
Methyl Esters ◽  
Pollution Prevention ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Minimal Amount

Biodiesel produced by transesterification process from vegetable oils or animal fats is viewed as a promising renewable energy source. Now a day’s diminishing of petroleum reserves in the ground and increasing environmental pollution prevention and regulations have made searching for renewable oxygenated energy sources from biomasses. Biodiesel is non-toxic, renewable, biodegradable, environmentally benign, energy efficient and diesel substituent fuel used in diesel engine which contributes minimal amount of global warming gases such as CO, CO2, SO2, NOX, unburned hydrocarbons, and particulate matters. The chemical composition of the biodiesel was examined by help of GC-MS and five fatty acid methyl esters such as methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linoleneate were identified. The variables that affect the amount of biodiesel such as methanol/oil molar ratio, mass weight of catalyst and temperature were studied. In addition to this the physicochemical properties of the biodiesel such as (density, kinematic viscosity, iodine value high heating value, flash point, acidic value, saponification value, carbon residue, peroxide value and ester content) were determined and its corresponding values were 87 Kg/m3, 5.63 Mm2/s, 39.56 g I/100g oil, 42.22 MJ/Kg, 132oC, 0.12 mgKOH/g, 209.72 mgKOH/g, 0.04%wt, 12.63 meq/kg, and 92.67 wt% respectively. The results of the present study showed that all physicochemical properties lie within the ASTM and EN biodiesel standards. Therefore, mango seed oil methyl ester could be used as an alternative to diesel engine.

Efficient Micromixing for Continuous Biodiesel Production from Jatropha Oil

2018 ◽  
Vol 9 (1) ◽  
pp. 133-139
Author(s):  
Waleed S. Mohammed ◽  
Ahmed H. El-Shazly ◽  
Marwa F. Elkady ◽  
Masahiro Ohshima
Keyword(s):  
Methyl Esters ◽  
Continuous Process ◽  
Sol Gel ◽  
Average Diameter ◽  
Biodiesel Production ◽  
High Mass ◽  
Molar Ratio ◽  
Jatropha Oil ◽  
Energy Deficiency ◽  
Gel Preparation

Introduction: The utilization of biodiesel as an alternative fuel is turning out to be progressively famous these days because of worldwide energy deficiency. The enthusiasm for utilizing Jatropha as a non-edible oil feedstock is quickly developing. The performance of the base catalyzed methanolysis reaction could be improved by a continuous process through a microreactor in view of the high mass transfer coefficient of this technique. Materials & Methods: Nanozirconium tungstovanadate, which was synthetized using sol-gel preparation method, was utilized in a complementary step for biodiesel production process. The prepared material has an average diameter of 0.066 &µm. Results: First, the NaOH catalyzed methanolysis of Jatropha oil was investigated in a continuous microreactor, and the efficient mixing over different mixers and its impact on the biodiesel yield were studied under varied conditions. Second, the effect of adding the nanocatalyst as a second stage was investigated. Conclusion: The maximum percentage of produced methyl esters from Jatropha oil was 98.1% using a methanol/Jatropha oil molar ratio of 11 within 94 s using 1% NaOH at 60 &°C. The same maximum conversion ratio was recorded with the nanocatalyst via only 0.3% NaOH.

scholarly journals Biodiesel Production on Monometallic Pt, Pd, Ru, and Ag Catalysts Supported on Natural Zeolite

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 48
Author(s):  
Pawel Mierczynski ◽  
Magdalena Mosińska ◽  
Lukasz Szkudlarek ◽  
Karolina Chalupka ◽  
Misa Tatsuzawa ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Natural Zeolite ◽  
Noble Metals ◽  
Methyl Esters ◽  
Physicochemical Characteristics ◽  
Biodiesel Production ◽  
X Ray Diffraction ◽  
X Ray ◽  
Yield Values ◽  
Temperature Programmed

Biodiesel production from rapeseed oil and methanol via transesterification reaction facilitated by various monometallic catalyst supported on natural zeolite (NZ) was investigated. The physicochemical characteristics of the synthesized catalysts were studied by X-ray diffraction (XRD), Brunauer–Emmett–Teller method (BET), temperature-programmed-reduction in hydrogen (H2-TPR), temperature-programmed-desorption of ammonia (NH3-TPD), Scanning Electron Microscope equipped with EDX detector (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) methods. The highest activity and methyl ester yields were obtained for the Pt/NZ catalyst. This catalyst showed the highest triglycerides conversion of 98.9% and fatty acids methyl esters yields of 94.6%. The activity results also confirmed the high activity of the carrier material (NZ) itself in the investigated reaction. Support material exhibited 90.5% of TG conversion and the Fatty Acid Methyl Esters yield (FAME) of 67.2%. Introduction of noble metals improves the TG conversion and FAME yield values. Increasing of the metal loading from 0.5 to 2 wt.% improves the reactivity properties of the investigated catalysts.

scholarly journals Optimizing the catalytic activities of methanol and thermotolerant Kocuria flava lipases for biodiesel production from cooking oil wastes

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Azhar Najjar ◽  
Elhagag Ahmed Hassan ◽  
Nidal Zabermawi ◽  
Saber H. Saber ◽  
Leena H. Bajrai ◽  
...  
Keyword(s):  
Ph Value ◽  
Energy Content ◽  
Value Added ◽  
Relative Activity ◽  
Economic Feasibility ◽  
Biodiesel Production ◽  
Molar Ratios ◽  
Cooking Oil ◽  
Enzyme Biocatalysis ◽  
Methanol Tolerant

AbstractIn this study, two highly thermotolerant and methanol-tolerant lipase-producing bacteria were isolated from cooking oil and they exhibited a high number of catalytic lipase activities recording 18.65 ± 0.68 U/mL and 13.14 ± 0.03 U/mL, respectively. Bacterial isolates were identified according to phenotypic and genotypic 16S rRNA characterization as Kocuria flava ASU5 (MT919305) and Bacillus circulans ASU11 (MT919306). Lipases produced from Kocuria flava ASU5 showed the highest methanol tolerance, recording 98.4% relative activity as well as exhibited high thermostability and alkaline stability. Under the optimum conditions obtained from 3D plots of response surface methodology design, the Kocuria flava ASU5 biocatalyst exhibited an 83.08% yield of biodiesel at optimized reaction variables of, 60 ○C, pH value 8 and 1:2 oil/alcohol molar ratios in the reaction mixture. As well as, the obtained results showed the interactions of temperature/methanol were significant effects, whereas this was not noted in the case of temperature/pH and pH/methanol interactions. The obtained amount of biodiesel from cooking oil was 83.08%, which was analyzed by a GC/Ms profile. The produced biodiesel was confirmed by Fourier-transform infrared spectroscopy (FTIR) approaches showing an absorption band at 1743 cm−1, which is recognized for its absorption in the carbonyl group (C=O) which is characteristic of ester absorption. The energy content generated from biodiesel synthesized was estimated as 12,628.5 kJ/mol. Consequently, Kocuria flava MT919305 may provide promising thermostable, methanol-tolerant lipases, which may improve the economic feasibility and biotechnology of enzyme biocatalysis in the synthesis of value-added green chemicals.

scholarly journals Enzymatic Transesterification of Waste Frying Oil from Local Restaurants in East Colombia Using a Combined Lipase System

2020 ◽  
Vol 10 (10) ◽  
pp. 3566
Author(s):  
Mary Angélica Ferreira Vela ◽  
Juan C. Acevedo-Páez ◽  
Nestor Urbina-Suárez ◽  
Yeily Adriana Rangel Basto ◽  
Ángel Darío González-Delgado
Keyword(s):  
Reaction Time ◽  
Methyl Esters ◽  
Enzyme Concentration ◽  
Operating Conditions ◽  
Frying Oil ◽  
Biodiesel Production ◽  
Optimum Operating ◽  
Waste Frying Oil ◽  
Production Chain ◽  
Enzymatic Transesterification

The search for innovation and biotechnological strategies in the biodiesel production chain have become a topic of interest for scientific community owing the importance of renewable energy sources. This work aimed to implement an enzymatic transesterification process to obtain biodiesel from waste frying oil (WFO). The transesterification was performed by varying reaction times (8 h, 12 h and 16 h), enzyme concentrations of lipase XX 25 split (14%, 16% and 18%), pH of reaction media (6, 7 and 8) and reaction temperature (35, 38 and 40 °C) with a fixed alcohol–oil molar ratio of 3:1. The optimum operating conditions were selected to quantify the amount of fatty acid methyl esters (FAMEs) generated. The highest biodiesel production was reached with an enzyme concentration of 14%, reaction time of 8 h, pH of 7 and temperature of 38 °C. It was estimated a FAMEs production of 42.86% for the selected experiment; however, best physicochemical characteristics of biodiesel were achieved with an enzyme concentration of 16% and reaction time of 8 h. Results suggested that enzymatic transesterification process was favorable because the amount of methyl esters obtained was similar to the content of fatty acids in the WFO.

scholarly journals Value-Added Products from Urea Glycerolysis Using a Heterogeneous Biosolids-Based Catalyst

Catalysts ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 373 ◽  
Author(s):  
Mattia Bartoli ◽  
Chengyong Zhu ◽  
Michael Chae ◽  
David Bressler
Keyword(s):  
Weight Ratio ◽  
Value Added ◽  
Economic Feasibility ◽  
Biodiesel Production ◽  
Wastewater Management ◽  
Thermal Hydrolysis ◽  
Process Economics ◽  
Air Stream ◽  
Increasing Temperature ◽  
Value Added Products

Although thermal hydrolysis of digested biosolids is an extremely promising strategy for wastewater management, the process economics are prohibitive. Here, a biosolids-based material generated through thermal hydrolysis was used as a catalyst for urea glycerolysis performed under several conditions. The catalytic system showed remarkable activity, reaching conversion values of up to 70.8 ± 0.9% after six hours, at 140 °C using a catalyst/glycerol weight ratio of 9% and an air stream to remove NH3 formed during the process. Temperature played the most substantial role among reaction parameters; increasing temperature from 100 °C to 140 °C improved conversion by 35% and glycidol selectivity by 22%. Furthermore, the catalyst retained good activity even after the fourth catalytic run (conversion rate of 56.4 ± 1.3%) with only a slight decrease in glycidol selectivity. Thus, the use of a biosolids-based catalyst may facilitate conversion of various glycerol sources (i.e., byproduct streams from biodiesel production) into value-added products such as glycidol, and may also improve the economic feasibility of using thermal hydrolysis for treatment of biosolids.

Optimized Preparation of Moringa Oleifera Methyl Esters Using Sulfated Tin Oxide as Heterogenous Catalyst

2010 ◽  
Author(s):  
Gerald Kafuku ◽  
Makme Mbarawa ◽  
Man Kee Lam ◽  
Keat Teong Lee
Keyword(s):  
Tin Oxide ◽  
Heterogeneous Catalysts ◽  
Moringa Oleifera ◽  
Methyl Esters ◽  
Biodiesel Production ◽  
Solid Catalyst ◽  
Separation And Purification ◽  
Animal Fats ◽  
Super Acid ◽  
Moringa Oleifera Oil

Fatty acid methyl esters (biodiesel), prepared from transesterification of vegetable oils or animal fats, have gained great importance in substituting petroleum based diesel for combating environmental problems and higher diesel prices. Moringa oleifera fatty acids are among the newly investigated potentials for biodiesel production in recent years. In getting rid of soap formation and thus large waste washing water from biodiesel produced from homogenous catalysts, the use of heterogeneous catalysts is currently preferred due to easily separation and purification of the final products. In this study, biodiesel was produced from moringa oleifera oil using sulfated tin oxide enhanced with SiO2 (SO42−/SnO2−SiO2) as super acid solid catalyst. The experimental design was done using design of experiment (DoE), specifically, response surface methodology based on three-variable central composite design (CCD) with alpha (α) = 2. The reaction parameters in the optimization process were reaction temperature (60°C to 180°C), reaction period (1 to 3 hrs) and methanol to oil ratio (1:6 to 1:24 mol/mol). It was observed that the yield up to 84wt% of moringa oleifera methyl esters can be obtained with reaction conditions of 150°C temperature, 150 minutes reaction time and 1:19.5 methanol to oil ratio, while catalyst concentration and agitation speed are kept at 3wt% and 350 rpm respectively.

scholarly journals RAPE SEED OIL TETRAHYDROFURFURYLESTERS

2015 ◽  
Vol 1 ◽  
pp. 46
Author(s):  
K. Malins ◽  
V. Kampars ◽  
R. Kampare ◽  
T. Rusakova
Keyword(s):  
Rapeseed Oil ◽  
Fossil Fuels ◽  
Raw Materials ◽  
Methyl Esters ◽  
Cetane Number ◽  
Food Prices ◽  
Raw Material ◽  
Biodiesel Production ◽  
Cold Filter Plugging Point ◽  
Mineral Oils

The transesterification of vegetable oil using various kinds of alcohols is a simple and efficient renewable fuel synthesis technique. Products obtained by modifying natural triglycerides in transesterification reaction substitute fossil fuels and mineral oils. Currently the most significant is the biodiesel, a mixture of fatty acid methyl esters, which is obtained in a reaction with methanol, which in turn is obtained from fossil raw materials. In biodiesel production it would be more appropriate to use alcohols which can be obtained from renewable local raw materials. Ethanol rouses interest as a possible reagent, however, its production locally is based on the use of grain and therefore competes with food production so it would implicitly cause increase in food prices. Another raw material option is alcohols that can be obtained from furfurole. Furfurole is obtained in dehydration process from pentose sugars which can be extracted from crop straw, husk and other residues of agricultural production. From furfurole the tetrahydrofurfuryl alcohol (THFA), a raw material for biodiesel, can be produced. By transesterifying rapeseed oil with THFA it would be possible to obtain completely renewable biodiesel with properties very close to diesel [2-4]. With the purpose of developing the synthesis of such fuel, in this work a three-stage synthesis of rapeseed oil tetrahydrofurfurylesters (ROTHFE) in sulphuric acid presence has been performed, achieving product with purity over 98%. The most important qualitative factors of ROTHFE have been determined - cold filter plugging point, cetane number, water content, Iodine value, phosphorus content, density, viscosity and oxidative stability.

scholarly journals An Integrated Methodology towards Mitigation of Global Warming and Biomass Production for Biodiesel using Chlorella sorokiniana BTA 9031

2019 ◽  
Vol 8 (4) ◽  
pp. 3054-3058
Keyword(s):  
Flow Rate ◽  
Gas Flow ◽  
Methyl Esters ◽  
Research Work ◽  
Co2 Concentration ◽  
Chlorella Sorokiniana ◽  
Biodiesel Production ◽  
Co2 Absorption ◽  
Microalgal Biomass ◽  
Microalgal Cultivation

The rise of atmospheric carbon dioxide (CO2 )concentration as well as depletion of fossil fuel reserves calls for the development of clean and ecofriendly alternative fuel source. Recently, lipid rich microalgal biomass is being extensively studied for generation of biodiesel however, the expensesincurred on production of microalgal biomassis a significant hurdle. Almost 80 % of the production costis generated from the cultivation medium which majorly comprise of carbon, nitrogen and phosphate. If the microalgal cultivation could be linked to a CO2 capturing unit than the cost of production could be reduced to a large extent. CO2 absorption by means of aqueous amine solvents is known to be a mature technology and could be integrated with microalgal cultivation unit for efficient utilization of the captured CO2 . In this present research work, blended solution of piperazine (PZ) and2-amino2-methyl-1-propanol (AMP) (5/25 wt. %) was used to capture CO2 and then the captured CO2 was utilized as an inorganic carbon stream for growing Chlorella sorokiniana BTA 9031 for biodiesel production. The CO2rate absorption was governed by series of process variablesviz.solvent flow rate ranges (1.5 to 3) ×10⁻4 m 3 min-1 , absorption temperature (298 to 313) K,concentration of CO2 (10 to 15) kPa and gas flow rate(5 to 8) ×10⁻3 m 3 min-1 . The detected final biomass strengthofChlorella sorokiniana BTA 9031 was0.955g L-1 . The fatty acid methyl esters (FAME) determinedsubsequentlyacid transesterification was observed to contain fatty acids suitable for biodiesel production.

Sign in / Sign up

Export Citation Format

Share Document