Effect of Sheet Temperature on Thickness Distribution of the Thermoformed Hemispherical Dome

2020 ◽  
pp. 479-487
Author(s):  
Jeet P. Patil ◽  
Yogesh S. Gaikhe ◽  
Vilas Nandedkar ◽  
Sushil Mishra
Keyword(s):  
Thickness Distribution ◽  
Hemispherical Dome

Photographic Equidensitometry of High Voltage Electron Images of Thick Noncrystalline Materials

1972 ◽  
Vol 30 ◽  
pp. 594-595
Author(s):  
Keinosuke Kobayashi
Keyword(s):  
High Voltage ◽  
Linear Response ◽  
Thickness Distribution ◽  
Contour Map ◽  
Mass Thickness ◽  
Voltage Electron ◽  
High Voltage Electron ◽  
Homogeneous Particle ◽  
Photographic Emulsions ◽  
Logarithmic Relation

Equidensitometry as developed by E. Lau and W. Krug has been little used in the analysis of ordinary electron photomicrographs, yet its application to the high voltage electron images proves merits of this procedure. Proper sets (families) of equidensities as shown in the next page are able to reveal the contour map of mass thickness distribution in thick noncrystalline specimens. The change in density of the electron micrograph is directly related to the mass thickness of corresponding area in the specimen, because of the linear response of photographic emulsions to electrons and the logarithmic relation between electron opacity and mass thickness of amorphous object.This linearity is verified by equidensitometry of a spherical solid object as shown in Fig. 1a. The object is a large (1 μ) homogeneous particle of polystyrene. Fig. 1b is a composite print of three equidensities of the 1st order prepared from Fig. 1a.

Aerodynamic Shape Influence and Optimum Thickness Distribution Analysis of Perceptive Wind Turbine Blade

2018 ◽  
Vol 7 (3) ◽  
pp. 1
Author(s):  
J. V. Muruga Lal Jeyan ◽  
Akhila Rupesh ◽  
Jency Lal
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Thickness Distribution ◽  
Turbine Blades ◽  
Reduced Form ◽  
Load Factor ◽  
Strong Impact ◽  
Theory Approach ◽  
Distribution Analysis ◽  
Optimum Thickness

The aerodynamic module combines the three-dimensional nonlinear lifting surface theory approach, which provides the effective propagated incident velocity and angle of attack at the blade section separately, and a two-dimensional panel method for steady axisymmetric and non-symmetric flow has to be involved to obtain the 3D pressure and velocity distribution on the wind mill model blade. Wind mill and turbines have become an economically competitive form of efficiency and renewable work generation. In the abroad analytical studies, the wind turbine blades to be the target of technological improvements by the use of highly possible systematic , aerodynamic and design, material analysis, fabrication and testing. Wind energy is a peculiar form of reduced form of density source of power. To make wind power feasible, it is important to optimize the efficiency of converting wind energy into productivity source. Among the different aspects involved, rotor aerodynamics is a key determinant for achieving this goal. There is a tradeoff between thin airfoil and structural efficiency. Both of which have a strong impact on the cost of work generated. Hence the design and analysis process for optimum design requires determining the load factor, pressure and velocity impact and optimum thickness distribution by finding the effect of blade shape by varying thickness on the basis of both the aerodynamic output and the structural weight.

Combining SAR interferometry and the equation of continuity to estimate the three-dimensional glacier surface-velocity vector

1999 ◽  
Vol 45 (151) ◽  
pp. 533-538 ◽  
Author(s):  
Niels Reeh ◽  
Søren Nørvang Madsen ◽  
Johan Jakob Mohr
Keyword(s):  
Steady State ◽  
Mass Balance ◽  
Vertical Velocity ◽  
Velocity Vector ◽  
Thickness Distribution ◽  
Vertical Surface ◽  
Horizontal Velocity ◽  
Sar Interferometry ◽  
Surface Velocity ◽  
Ice Thickness

AbstractUntil now, an assumption of surface-parallel glacier flow has been used to express the vertical velocity component in terms of the horizontal velocity vector, permitting all three velocity components to be determined from synthetic aperture radar interferometry. We discuss this assumption, which neglects the influence of the local mass balance and a possible contribution to the vertical velocity arising if the glacier is not in steady state. We find that the mass-balance contribution to the vertical surface velocity is not always negligible as compared to the surface-slope contribution. Moreover, the vertical velocity contribution arising if the ice sheet is not in steady state can be significant. We apply the principle of mass conservation to derive an equation relating the vertical surface velocity to the horizontal velocity vector. This equation, valid for both steady-state and non-steady-state conditions, depends on the ice-thickness distribution. Replacing the surface-parallel-flow assumption with a correct relationship between the surface velocity components requires knowledge of additional quantities such as surface mass balance or ice thickness.

scholarly journals Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3993
Author(s):  
Thanh Trung Do ◽  
Pham Son Minh ◽  
Nhan Le
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Side Wall ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

scholarly journals Ice thickness distribution of all Swiss glaciers based on extended ground-penetrating radar data and glaciological modeling

2021 ◽  
pp. 1-19
Author(s):  
Melchior Grab ◽  
Enrico Mattea ◽  
Andreas Bauder ◽  
Matthias Huss ◽  
Lasse Rabenstein ◽  
...  
Keyword(s):  
Ground Penetrating Radar ◽  
Thickness Distribution ◽  
Radar Data ◽  
Tourism Industry ◽  
Swiss Alps ◽  
Ice Thickness ◽  
Hazard Management ◽  
Bed Topography ◽  
Ice Volume ◽  
Ground Penetrating

Abstract Accurate knowledge of the ice thickness distribution and glacier bed topography is essential for predicting dynamic glacier changes and the future developments of downstream hydrology, which are impacting the energy sector, tourism industry and natural hazard management. Using AIR-ETH, a new helicopter-borne ground-penetrating radar (GPR) platform, we measured the ice thickness of all large and most medium-sized glaciers in the Swiss Alps during the years 2016–20. Most of these had either never or only partially been surveyed before. With this new dataset, 251 glaciers – making up 81% of the glacierized area – are now covered by GPR surveys. For obtaining a comprehensive estimate of the overall glacier ice volume, ice thickness distribution and glacier bed topography, we combined this large amount of data with two independent modeling algorithms. This resulted in new maps of the glacier bed topography with unprecedented accuracy. The total glacier volume in the Swiss Alps was determined to be 58.7 ± 2.5 km3 in the year 2016. By projecting these results based on mass-balance data, we estimated a total ice volume of 52.9 ± 2.7 km3 for the year 2020. Data and modeling results are accessible in the form of the SwissGlacierThickness-R2020 data package.

scholarly journals Film Thickness-Profile Measurement Using Iterative Peak Separation Structured Illumination Microscopy

2021 ◽  
Vol 11 (7) ◽  
pp. 3023
Author(s):  
Kejun Yang ◽  
Chenhaolei Han ◽  
Jinhua Feng ◽  
Yan Tang ◽  
Zhongye Xie ◽  
...  
Keyword(s):  
Modulation Depth ◽  
Thickness Distribution ◽  
Detection Threshold ◽  
Profile Measurement ◽  
Structured Illumination ◽  
Structured Illumination Microscopy ◽  
Separation Algorithm ◽  
Peak Separation ◽  
Lower Detection ◽  
Depth Response

The surface and thickness distribution measurement for transparent film is of interest for electronics and packaging materials. Structured illumination microscopy (SIM) is a prospective technique for measuring film due to its high accuracy and efficiency. However, when the distance between adjacent layers becomes close, the peaks of the modulation depth response (MDR) start to overlap and interfere with the peak extraction, which restricts SIM development in the field of film measurement. In this paper, an iterative peak separation algorithm is creatively applied in the SIM-based technique, providing a precise peak identification even as the MDR peaks overlap and bend into one. Compared with the traditional method, the proposed method has a lower detection threshold for thickness. The experiments and theoretical analysis are elaborated to demonstrate the feasibility of the mentioned method.

scholarly journals Formability study and metallurgical properties analysis of FSWed AA 6061 blank by the SPIF process

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Payam Tayebi ◽  
Ali Fazli ◽  
Parviz Asadi ◽  
Mahdi Soltanpour
Keyword(s):  
Base Metal ◽  
Strain Distribution ◽  
Thickness Distribution ◽  
Experimental Studies ◽  
Welding Process ◽  
Forming Limit ◽  
Forming Process ◽  
Friction Stir ◽  
Numerical Process ◽  
Tailor Welded Blank

AbstractIn this study, in order to obtain the maximum possible formability in tailor-welded blank AA6061 sheets connected by the friction stir welding (FSW) procedure, the incremental sheet forming process has been utilized. The results are presented both numerically and experimentally. To obtain the forming limit angle, the base and FSWed sheets were formed in different angles with conical geometry, and ultimately, the forming limit angle for the base metal and FSWed sheet is estimated to be 60° and 57.5°, respectively. To explore the effects of welding and forming procedures on AA6061 sheets, experimental studies such as mechanical properties, microstructure and fracture analysis are carried out on the samples. Also, the thickness distribution of the samples is studied to investigate the effect of the welding process on the thickness distribution. Then, the numerical process was simulated by the ABAQUS commercial software to study the causes of the FSWed samples failure through analyzing the thickness distribution parameter, and major and minor strains and the strain distribution. Causes of failure in FSWed samples include increased minor strain, strain distribution and thickness distribution in welded areas, especially in the proximity of the base metal area.

scholarly journals Controlling Film Thickness Distribution by Magnetron Sputtering with Rotation and Revolution

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 599
Author(s):  
Handan Huang ◽  
Li Jiang ◽  
Yiyun Yao ◽  
Zhong Zhang ◽  
Zhanshan Wang ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Film Thickness ◽  
Multilayer Film ◽  
Thickness Distribution ◽  
Parabolic Cylinder ◽  
Particle Model ◽  
Planetary Motion ◽  
X Rays ◽  
X Ray ◽  
Sputtering System

The laterally graded multilayer collimator is a vital part of a high-precision diffractometer. It is applied as condensing reflectors to convert divergent X-rays from laboratory X-ray sources into a parallel beam. The thickness of the multilayer film varies with the angle of incidence to guarantee every position on the mirror satisfies the Bragg reflection. In principle, the accuracy of the parameters of the sputtering conditions is essential for achieving a reliable result. In this paper, we proposed a precise method for the fabrication of the laterally graded multilayer based on a planetary motion magnetron sputtering system for film thickness control. This method uses the fast and slow particle model to obtain the particle transport process, and then combines it with the planetary motion magnetron sputtering system to establish the film thickness distribution model. Moreover, the parameters of the sputtering conditions in the model are derived from experimental inversion to improve accuracy. The revolution and rotation of the substrate holder during the final deposition process are achieved by the speed curve calculated according to the model. Measurement results from the X-ray reflection test (XRR) show that the thickness error of the laterally graded multilayer film, coated on a parabolic cylinder Si substrate, is less than 1%, demonstrating the effectiveness of the optimized method for obtaining accurate film thickness distribution.

scholarly journals Measuring and inferring the ice thickness distribution of four glaciers in the Tien Shan, Kyrgyzstan

2020 ◽  
pp. 1-18
Author(s):  
Lander Van Tricht ◽  
Philippe Huybrechts ◽  
Jonas Van Breedam ◽  
Johannes J. Fürst ◽  
Oleg Rybak ◽  
...  
Keyword(s):  
Cross Validation ◽  
Thickness Distribution ◽  
Tien Shan ◽  
Ice Thickness ◽  
Ice Volume ◽  
In Situ Data ◽  
Radio Echo Sounding ◽  
Thickness Measurements ◽  
Tien Shan Mountains

Abstract Glaciers in the Tien Shan mountains contribute considerably to the fresh water used for irrigation, households and energy supply in the dry lowland areas of Kyrgyzstan and its neighbouring countries. To date, reconstructions of the current ice volume and ice thickness distribution remain scarce, and accurate data are largely lacking at the local scale. Here, we present a detailed ice thickness distribution of Ashu-Tor, Bordu, Golubin and Kara-Batkak glaciers derived from radio-echo sounding measurements and modelling. All the ice thickness measurements are used to calibrate three individual models to estimate the ice thickness in inaccessible areas. A cross-validation between modelled and measured ice thickness for a subset of the data is performed to attribute a weight to every model and to assemble a final composite ice thickness distribution for every glacier. Results reveal the thickest ice on Ashu-Tor glacier with values up to 201 ± 12 m. The ice thickness measurements and distributions are also compared with estimates composed without the use of in situ data. These estimates approach the total ice volume well, but local ice thicknesses vary substantially.

scholarly journals Ice thickness distribution and volume estimation of Burqin Glacier No. 18 in the Chinese Altay Mountains

2020 ◽  
Author(s):  
Shuang Jin ◽  
Zhongqin Li ◽  
Zemin Wang ◽  
Feiteng Wang ◽  
Chunhai Xu ◽  
...  
Keyword(s):  
Thickness Distribution ◽  
Volume Estimation ◽  
Ice Thickness ◽  
Altay Mountains
Sign in / Sign up

Export Citation Format

Share Document