scholarly journals Design of power-efficient CMOS based oscillator circuit with varactor tuning control

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Dileep Dwivedi ◽  
Manoj Kumar ◽  
Vandana Niranjan
Keyword(s):  
Tuning Range ◽  
Cell Voltage ◽  
Current Mode ◽  
Control Voltage ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Power Efficient ◽  
Differential Delay ◽  
Variable Capacitance ◽  
Mos Varactor

AbstractThis paper presents a low-power, wide tuning range CMOS voltage-controlled oscillator with MCML (MOS current mode logic) differential delay cell. Voltage controlled oscillator (VCO) circuit is designed in TSMC 0.25 μm CMOS process. To achieve the broad frequency range concept of variable capacitance is employed in the proposed VCO circuit. Source/drain tuning voltage (Vtune) and body bias voltage (Vb) of I-MOS varactor are used to achieve variable capacitance at different I-MOS varactor widths (W). The dual control voltage of I-MOS varactor results in a tuning range from 0.528 GHz to 2.014 GHz. VCO's figure of merit (FoM) is 152.13 dBc/Hz with phase noise of −93.77 dBc/Hz at 1 MHz offset from the oscillation frequency. The proposed VCO dissipates maximum power of 3.127 mW.

scholarly journals An Ultra-Low-Power K-Band 22.2 GHz-to-26.9 GHz Current-Reuse VCO Using Dynamic Back-Gate-Biasing Technique

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 889
Author(s):  
Xiaoying Deng ◽  
Peiqi Tan
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Tuning Range ◽  
Frequency Tuning ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Back Gate ◽  
Ultra Low Power ◽  
Current Reuse ◽  
K Band

An ultra-low-power K-band LC-VCO (voltage-controlled oscillator) with a wide tuning range is proposed in this paper. Based on the current-reuse topology, a dynamic back-gate-biasing technique is utilized to reduce power consumption and increase tuning range. With this technique, small dimension cross-coupled pairs are allowed, reducing parasitic capacitors and power consumption. Implemented in SMIC 55 nm 1P7M CMOS process, the proposed VCO achieves a frequency tuning range of 19.1% from 22.2 GHz to 26.9 GHz, consuming only 1.9 mW–2.1 mW from 1.2 V supply and occupying a core area of 0.043 mm2. The phase noise ranges from −107.1 dBC/HZ to −101.9 dBc/Hz at 1 MHz offset over the whole tuning range, while the total harmonic distortion (THD) and output power achieve −40.6 dB and −2.9 dBm, respectively.

Ground-Adjustable Inductor for Wide-Tuning VCO Design

2012 ◽  
Vol 256-259 ◽  
pp. 2373-2378
Author(s):  
Wu Shiung Feng ◽  
Chin I Yeh ◽  
Ho Hsin Li ◽  
Cheng Ming Tsao
Keyword(s):  
Power Consumption ◽  
Tuning Range ◽  
Supply Voltage ◽  
Wide Band ◽  
Ultra Wide Band ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Wide Tuning Range ◽  
Chip Area ◽  
Ground Plate

A wide-tuning range voltage-controlled oscillator (VCO) with adjustable ground-plate inductor for ultra-wide band (UWB) application is presented in this paper. The VCO was implemented by standard 90nm CMOS process at 1.2V supply voltage and power consumption of 6mW. The tuning range from 13.3 GHz to 15.6 GHz with phase noise between -99.98 and -115dBc/Hz@1MHz is obtained. The output power is around -8.7 to -9.6dBm and chip area of 0.77x0.62mm2.

A Scalable Millimetre-Wave Differential CMOS Cross-Coupled VCO for Automotive Radar Application

2018 ◽  
Vol 27 (10) ◽  
pp. 1850158 ◽  
Author(s):  
Rekha Yadav ◽  
Pawan Kumar Dahiya ◽  
Rajesh Mishra
Keyword(s):  
Phase Noise ◽  
Oxide Semiconductor ◽  
Control Voltage ◽  
Cmos Process ◽  
Operating Voltage ◽  
Voltage Controlled Oscillator ◽  
Automotive Radar ◽  
Millimetre Wave ◽  
The Impact ◽  
Lc Vco

In this paper, a novel method to realize LC Voltage-Controlled-Oscillator (LC-VCO) operating at 76.2–76.7[Formula: see text]GHz frequency band for microwave RFIC component is presented. The model of cross-coupled differential LC-VCO is designed in 45[Formula: see text]nm technology using Complementary Metal Oxide Semiconductor (CMOS) process for Frequency Modulated Carrier Wave (FMCW) automotive radar sensors and RF transceivers application. The impact of VDD, control voltage and temperature variation on frequency shift, phase noise, and output power has been analyzed to optimize the trade-off between frequency, phase noise, and power requirement. The results depict that LC-VCO dissipates 10.45[Formula: see text]mW power at an operating voltage of 1.5[Formula: see text]V. The phase noise has been observed to be [Formula: see text]90[Formula: see text]dBc/Hz at 1[Formula: see text]MHz offset at 76[Formula: see text]GHz carrier frequency. The estimated layout area of IC is [Formula: see text]m2. The result shows the edge of the design over existing techniques.

A 2.3 mW Multi-Frequency Clock Generator with −137 dBc/Hz Phase Noise VCO in 180 nm Digital CMOS Technology

2019 ◽  
Vol 29 (08) ◽  
pp. 2050130 ◽  
Author(s):  
Jagdeep Kaur Sahani ◽  
Anil Singh ◽  
Alpana Agarwal
Keyword(s):  
Phase Noise ◽  
Supply Voltage ◽  
Dead Zone ◽  
Dynamic Logic ◽  
Cmos Technology ◽  
Control Voltage ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Cmos Inverter ◽  
Digital Cmos

A fast phase frequency detector (PFD) and low gain low phase noise voltage-controlled oscillator (VCO)-based phase-locked loop (PLL) design are presented in this paper. PLL works in the frequency range of 0.025–1.6[Formula: see text]GHz, targeting various SoC applications. The proposed PFD, designed using CMOS dynamic logic, is fast and improves the locking time, dead zone and blind zone in the PLL. The standard CMOS inverter gate-based pseudo differential VCO is used in the PLL. Also, CMOS inverter is used as variable capacitor to tune the frequency of VCO with control voltage. The proposed PLL is designed in a 180[Formula: see text]nm CMOS process with supply voltage of 1.8[Formula: see text]V. The phase noise of VCO is [Formula: see text][Formula: see text]dBc/Hz at an offset frequency of 100[Formula: see text]MHz. The reference clock of 25[Formula: see text]MHz synthesizes the output clock of 1.6[Formula: see text]GHz with rms jitter of 0.642[Formula: see text]ps.

scholarly journals A Very Low-phase-noise CMOS Ring VCO Intended for Sensor Interfaces

2021 ◽  
Author(s):  
Mahin Esmaeilzadeh ◽  
Yves Audet ◽  
Mohamed Ali ◽  
Mohamad Sawan
Keyword(s):  
Phase Noise ◽  
Tuning Range ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Silicon Area ◽  
Wide Range ◽  
Extended Frequency ◽  
Sensor Interfaces ◽  
Low Phase Noise ◽  
Analytical Expressions

<p>We describe in the paper a ring voltage-controlled oscillator (VCO) indicating an improved phase noise over a wide range of frequency offsets and an extended frequency/voltage tuning range. The phase noise is improved by leveraging a better linearity approach, while reducing the VCO gain and maintaining wide tuning range. The proposed VCO is a block of a time-domain comparator embedded in a monitoring and readout circuit of an industrial sensor interface. An analytical model is extracted resulting in closed-form expressions for both input-referred noise and phase noise of the VCO. Employing the analytical expressions, the contributed noise and phase noise limitations are fully addressed, and all the effective factors are investigated. The prototype of the proposed VCO was implemented and fabricated in a 0.35 µm CMOS process. The integrated VCO consumes 0.903 mW from a 3.3 V supply, when running at its maximum frequency of 9.37 MHz. The measured phase noise of the proposed VCO is -147.57 dBc/Hz at 1 MHz offset from the 9.37 MHz oscillation frequency, and the occupied silicon area of circuit is 0.005 mm<sup>2</sup>.</p>

scholarly journals A Design of Wide-Range and Low Phase Noise Linear Transconductance VCO with 193.76 dBc/Hz FoMT for mm-Wave 5G Transceivers

Electronics ◽  
2020 ◽  
Vol 9 (6) ◽  
pp. 935 ◽  
Author(s):  
Arash Hejazi ◽  
YoungGun Pu ◽  
Kang-Yoon Lee
Keyword(s):  
Phase Noise ◽  
Carrier Frequency ◽  
Tuning Range ◽  
Frequency Tuning ◽  
Cmos Process ◽  
Switched Capacitor ◽  
Voltage Controlled Oscillator ◽  
Wide Range ◽  
Layout Area ◽  
Low Phase Noise

This paper presents a wide-range and low phase noise mm-Wave Voltage Controlled Oscillator (VCO) based on the transconductance linearization technique. The proposed technique eliminates the deep triode region of the active part of the VCO, and lowers the noise introduced by the gm-cell. The switch sizes inside the switched capacitor bank of the VCO are optimized to minimize the resistance of the switches while keeping the wide tuning range. A new layout technique shortens the routing of the VCO outputs, and lowers the parasitic inductance and resistance of the VCO routing. The presented method prevents the reduction of the quality factor of the tank due to the long routing. The proposed VCO achieves a discrete frequency tuning range, of 14 GHz to 18 GHz, through a linear coarse and middle switched capacitor array, and offers superior phase noise performance compared to recent state-of-the-art VCO architectures. The design is implemented in a 45 nm CMOS process and occupies a layout area (including output buffers) of 0.14 mm2. The power consumption of the VCO core is 24 mW from the power supply of 0.8 V. The post-layout simulation result shows the VCO achieves the phase noise performances of −87.2 dBc/Hz and −113 dBc/Hz, at 100 kHz and 1 MHz offset frequencies from the carrier frequency of 14 GHz, respectively. In an 18 GHz carrier frequency, the results are −87.4 dBc/Hz and −110 dBc/Hz, accordingly.

scholarly journals A LOW PHASE NOISE, POWER EFFICIENT VOLTAGE CONTROLLED OSCILLATOR USING 0.18-μM CMOS TECHNOLOGY

2014 ◽  
pp. 256-259
Author(s):  
AJIT SAMASGIKAR
Keyword(s):  
Power Consumption ◽  
Phase Noise ◽  
Tuning Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Noise Power ◽  
Voltage Controlled Oscillator ◽  
Power Efficient ◽  
Sustained Oscillations ◽  
Low Phase Noise

A low phase noise, power efficient VCO using UMC 0.18μm CMOS technology has been proposed in this paper. The proposed VCO has a tuning range of 9.71GHz to 9.9GHz, with a phase noise of -79.88 dBc/Hz @ 600kHz offset. The Vtune ranging between 1V - 1.5V generates sustained oscillations. The maximum power consumption of the VCO is 11.9mW using a supply voltage of 1.8V with ±10% variation.

Wide Tuning Range Varactorless Tunable Active Inductor-Based Voltage Controlled Oscillator for Wireless Applications

2019 ◽  
Vol 28 (14) ◽  
pp. 1950242
Author(s):  
Omar Faruqe ◽  
Md Tawfiq Amin
Keyword(s):  
Tuning Range ◽  
Active Inductor ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Performance Parameters ◽  
Wide Tuning Range ◽  
Silicon Area ◽  
Wireless Applications ◽  
Dc Power ◽  
Tuning Frequency

This paper presents a varactorless tunable active inductor-based voltage controlled oscillator (VCO) in 90[Formula: see text]nm CMOS process. The proposed VCO yields a wide tuning range of 116% with an output frequency of 1.19–4.46[Formula: see text]GHz for the tuning voltage of 0.3–1.5[Formula: see text]V. It consumes a low dc power ranging from 2.44[Formula: see text]mW to 4.79[Formula: see text]mW for the specified tuning range. The variation of phase noise ranges from [Formula: see text][Formula: see text]dBc/Hz to [Formula: see text][Formula: see text]dBc/Hz at 1[Formula: see text]MHz offset with the change of tuning voltage as well as tuning frequency. The proposed varactorless VCO has a maximum Figure of Merit (FOM) of [Formula: see text][Formula: see text]dBc/Hz with a differential output power of 1.8[Formula: see text]dBm at tuning voltage of 0.7[Formula: see text]V. The elimination of varactor which abates the silicon area consumption and the minimization of the variation of performance parameters are the special outcomes of the proposed active inductor-based VCO. Comparing the performance parameters such as power consumption, FOM and tuning range, the proposed design outperforms most of the cited designs.

A Low Native Jitter Voltage Controlled Oscillator on 0.18μm CMOS Process

2011 ◽  
Vol 383-390 ◽  
pp. 6846-6850
Author(s):  
Zhuo Ma ◽  
Li Luo ◽  
Yang Guo ◽  
Lun Guo Xie ◽  
Ji Hua Chen
Keyword(s):  
Detailed Analysis ◽  
Order Effect ◽  
High Order ◽  
Control Voltage ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Test Chip ◽  
High Order Effect ◽  
Peak Value

In this thesis, a kind of jitter is focused on, which is called Native Jitter (NJ) of the Voltage Controlled Oscillator (VCO). The cause of NJ is the high order effect of the transistor itself in the VCO, and almost has no correlation with the control voltage or supply. The detailed analysis of the cause and the evaluation of this NJ is proposed in this paper, and an Inter-locked Dual-loop VCO (ID-VCO) is put forward, in which most of the NJ is eliminated. A test chip of the ID-VCO based on 0.18μm CMOS process is established. Compared with the classical single end VCO, the result shows that the peak to peak value and mean-root-square values of period jitter reduce 15.4% and 16.3%, the same values of cycle-to-cycle jitter reduce 9.82% and 6.98%, respectively.

Sign in / Sign up

Export Citation Format

Share Document