Modeling the impact of glass transition on the frequency-dependent complex conductivity of CNT-polymer nanocomposites

2021 ◽  
pp. 104195
Author(s):  
Xiaodong Xia ◽  
Zijian Du ◽  
Juanjuan Zhang ◽  
Jackie Li ◽  
George J. Weng
Keyword(s):  
Glass Transition ◽  
Polymer Nanocomposites ◽  
Complex Conductivity ◽  
Frequency Dependent ◽  
The Impact

scholarly journals Investigation of the functional network modifier loading on the stoichiometric ratio of epoxy resins and their dielectric properties

2021 ◽  
Author(s):  
Istebreq A. Saeedi ◽  
Sunny Chaudhary ◽  
Thomas Andritsch ◽  
Alun S. Vaughan
Keyword(s):  
Glass Transition ◽  
Dielectric Properties ◽  
Electrical Properties ◽  
Epoxy Resins ◽  
Functional Network ◽  
Cross Linking ◽  
Network Modifier ◽  
Epoxy Resin System ◽  
The Cross ◽  
The Impact

AbstractReactive molecular additives have often been employed to tailor the mechanical properties of epoxy resins. In addition, several studies have reported improved electrical properties in such systems, where the network architecture and included function groups have been modified through the use of so-called functional network modifier (FNM) molecules. The study reported here set out to investigate the effect of a glycidyl polyhedral oligomeric silsesquioxane (GPOSS) FNM on the cross-linking reactions, glass transition, breakdown strength and dielectric properties of an amine-cured epoxy resin system. Since many previous studies have considered POSS to act as an inorganic filler, a key aim was to consider the impact of GPOSS addition on the stoichiometry of curing. Fourier transform infrared spectroscopy revealed significant changes in the cross-linking reactions that occur if appropriate stoichiometric compensation is not made for the additional epoxide groups present on the GPOSS. These changes, in concert with the direct effect of the GPOSS itself, influence the glass transition temperature, dielectric breakdown behaviour and dielectric response of the system. Specifically, the work shows that the inclusion of GPOSS can result in beneficial changes in electrical properties, but that these gains are easily lost if consequential changes in the matrix polymer are not appropriately counteracted. Nevertheless, if the system is appropriately optimized, materials with pronounced improvements in technologically important characteristics can be designed.

Nature instigated Grey wolf algorithm for parametric optimization during machining (Milling) of polymer nanocomposites

2021 ◽  
pp. 089270572199320
Author(s):  
Prakhar Kumar Kharwar ◽  
Rajesh Kumar Verma
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Polymer Nanocomposites ◽  
Feed Rate ◽  
Fitness Function ◽  
Depth Of Cut ◽  
Multiwall Carbon Nanotube ◽  
Grey Wolf ◽  
Milling Characteristics ◽  
The Impact

The new era of engineering society focuses on the utilization of the potential advantage of carbon nanomaterials. The machinability facets of nanocarbon materials are passing through an initial stage. This article emphasizes the machinability evaluation and optimization of Milling performances, namely Surface roughness (Ra), Cutting force (Fc), and Material removal rate (MRR) using a recently developed Grey wolf optimization algorithm (GWOA). The Taguchi theory-based L27 orthogonal array (OA) was employed for the Machining (Milling) of polymer nanocomposites reinforced by Multiwall carbon nanotube (MWCNT). The second-order polynomial equation was intended for the analysis of the model. These mathematical models were used as a fitness function in the GWOA to predict machining performances. The ANOVA outcomes efficiently explore the impact of machine parameters on Milling characteristics. The optimal combination for lower surface roughness value is 1.5 MWCNT wt.%, 1500 rpm of spindle speed, 50 mm/min of feed rate, and 3 mm depth of cut. For lower cutting force, 1.0 wt.%, 1500 rpm, 90 mm/min feed rate and 1 mm depth of cut and the maximize MRR was acquired at 0.5 wt.%, 500 rpm, 150 mm/min feed rate and 3 mm depth of cut. The deviation of the predicted value from the experimental value of Ra, Fc, and MRR are found as 2.5, 6.5 and 5.9%, respectively. The convergence plot of all Milling characteristics suggests the application potential of the GWO algorithm for quality improvement in a manufacturing environment.

Silane Functionalized Ethylene/Diene Copolymer Modifiers in Composites of Heterophasic Polypropylene and Microsilica

2007 ◽  
Vol 15 (5) ◽  
pp. 343-355 ◽  
Author(s):  
S. Lipponen ◽  
P. Pietikäinen ◽  
U. Vainio ◽  
R. Serimaa ◽  
J.V. Seppälä
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Impact Strength ◽  
Ambient Temperature ◽  
Metallocene Catalyst ◽  
The Poor ◽  
Rubber Toughened ◽  
Rubbery Phase ◽  
The Impact

Ethylene/1,7-octadiene copolymer was polymerised with metallocene catalyst and hydrosilylated to form silane functionalised polyethylenes (PE-co-SiX, X=Cl, OEt, Ph). The functionalised species were tested as modifiers in composites of rubber toughened polypropylene (heterophasic PP, hPP) and microsilica filler (μSi). A metallocene-based functionalised PE (PE-co-SiF) produced earlier in our laboratory and three commercial grades of functionalised polyolefins (one PE- and two PP-based) were used as reference modifiers. Major differences were seen in the toughness of the composites both above and below the glass transition temperature (Tg) of PP. In addition to increasing the stiffness, the microsilica filler enhanced the toughness of the heterophasic polypropylene by over 200% at ambient temperature. Below the Tg of PP (at −20 °C), the influence of μSi was the opposite and the impact strength of the hPP/μSi composite was below that of unfilled hPP. With the addition of just 2 wt% of functionalised polyethylene, the poor cold toughness of hPP/μSi composite was improved by nearly 100%. With the same addition, the toughness of the composites at ambient temperature was improved by 50 to 100% compared with the unfilled hPP. This behaviour was explained by significant changes in the fracture mechanism. Addition of functionalised PE increased the concentration of microsilica in the rubbery phase, allowing the crack to enter that phase. The rubbery phase was also able to absorb a large amount of impact energy below the glass transition temperature of PP.

scholarly journals INFLUENCE OF ENVIRONMENTAL FACTORS ON PHYSICAL-MECHANICAL PROPERTIES OF POLYDIMETHYL ETHER OF NORBORENE -2;3-DICARBOXYLIC ACID

2017 ◽  
Vol 60 (5) ◽  
pp. 68 ◽  
Author(s):  
Galina S. Bozhenkova ◽  
Alexandra N. Tarakanovskaya ◽  
Oksana D. Tarnovskaya ◽  
Roman V. Ashirov
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Hydrochloric Acid ◽  
Environmental Factors ◽  
Dicarboxylic Acid ◽  
Uv Radiation ◽  
Accelerated Aging ◽  
The Impact

The article is devoted to the production of polymer by metathesis ring-opening polymerization under the influence of ruthenium initiator of type of Hoveyda-Grubbs II generation. The monomer used the mixture of dimethyl ether norbornene-2;3-dicarboxylic acid. The monomer was prepared by the Diels-Alder reaction of dicyclopentadiene and dimethyl maleate. The polymer was prepared in bulk of the monomer mixture. In this paper we have studied the physical and mechanical properties polydimethyl ether of norbornene-2;3-dicarboxylic acid; and assessed the impact of environmental factors on the change in properties of the polymer. As environmental factors; light; UV radiation; water; 0.1 M hydrochloric acid were applied; and accelerated aging conditions; which were held in a climate chamber. During performance we found that maintaining the polymer samples in the UV light chamber led to the slight increase in flexural modulus. In contrast; the polymer storage in water and in a hydrochloric acid solution for two months resulted in a slight decrease in the modulus of elasticity in bending index. These factors did not affect the change in the glass transition temperature of the polymer. Under the conditions of accelerated aging conducted for 1; 2 and 6 days after two cycles we observed the drop in modulus for bending of 8.5%; after 6 cycles of 13%. The glass transition temperature of polydimethyl ether of norbornene-2;3-dicarboxylic acid after 6 cycles decreased by only 3.4% in the climatic chamber. Studies have shown that the resulting polymer is resistant to water; hydrochloric acid; light and UV radiation; as well as it saves properties at a sufficient level for operation at conditions of accelerated aging. It should be noted that the tested polymer was prepared without additives; stabilizers and antioxidants. The proposed polymer can be used as a structural material for machine parts; including bulky.For citation:Bozhenkova G.S.; Tarakanovskaya A.N.; Tarnovskaya O.D.; Ashirov R.V. Influence of environmental factors on physical-mechanical properties of polydimethyl ether of norborene -2;3-dicarboxylic acid. Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol. 2017. V. 60. N 5. P. 68-73

scholarly journals Elucidating the Impact of Charge Selective Contact in Halide Perovskite Through Impedance Spectroscopy

2019 ◽  
Author(s):  
Mohd Taukeer Khan ◽  
Manuel Salado ◽  
Abdullah R. D. Almohammedi ◽  
Samrana Kazim ◽  
Shahzada Ahmad
Keyword(s):  
Solar Cells ◽  
Impedance Spectroscopy ◽  
Charge Carrier ◽  
Carrier Mobility ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Charge Carrier Mobility ◽  
Charge Accumulation ◽  
Frequency Dependent ◽  
The Impact

<p>The electron and hole selective contact (SC) play a pivotal role in the performance of perovskite solar cells. In order to separate the interfacial phenomenon from bulk, the influence of charge SC was elucidated, by means of impedance spectroscopy. The specific role played by TiO<sub>2</sub> and <i>Spiro-OMeTAD</i> as electron and hole SC in perovskite solar cells was investigated at short circuit condition at different temperatures. We have probed MAPbI<sub>3</sub> and (FAPbI<sub>3</sub>)<sub>0.85</sub>(MAPbBr<sub>3</sub>)<sub>0.15 </sub>and elucidated parameters such as charge carrier mobility, recombination resistance, time constant and charge carrier kinetics in perovskite layer and at the interface of perovskite/SC. Charge carrier mobility in mixed perovskite was found to be nearly two order of magnitude higher as compared to MAPbI<sub>3</sub>. Moreover, the carrier mobility in devices with only electron SC was found to be higher as compared only hole SC. The charge accumulation at TiO<sub>2</sub>/perovskite/<i>Spiro</i>-OMeTAD interfaces were studied via frequency dependent capacitance, revealing higher charge accumulation at perovskite/S<i>piro</i>-OMeTAD than at TiO<sub>2</sub>/perovskite interface. By performing varying temperature frequency dependent capacitance measurements the distribution of density of state within the bandgap of the perovskites, the emission rate of electrons from the trap states and traps activation energy was determined. </p>

scholarly journals Investigation on compatibility of PLA/PBAT blends modified by epoxy-terminated branched polymers through chemical micro-crosslinking

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Bo Wang ◽  
Yujuan Jin ◽  
Kai’er Kang ◽  
Nan Yang ◽  
Yunxuan Weng ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Glass Transition ◽  
Sem Analysis ◽  
Branched Polymers ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
The Difference ◽  
Physical And Chemical ◽  
The Impact

AbstractIn this study, a type of epoxy-terminated branched polymer (ETBP) was used as an interface compati- bilizer to modify the poly lactic acid (PLA)/poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30) blends. Upon addition of ETBP, the difference in glass transition temperature between PLA and PBAT became smaller. By adding 3.0 phr of ETBP, the elongation at break of the PLA/PBAT blends was found increased from 45.8% to 272.0%; the impact strength increased from 26.2 kJ·m−2 to 45.3 kJ·m−2. In SEM analysis, it was observed that the size of the dispersed PBAT particle decreased with the increasing of ETBP content. These results indicated that the compatibility between PLA and PBAT can be effectively enhanced by using ETBP as the modifier. The modification mechanism was discussed in detail. It proposes that both physical and chemical micro-crosslinking were formed, the latter of which was confirmed by gel content analysis.

scholarly journals Rheometer enabled study of cartilage frequency-dependent properties

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Stefano Perni ◽  
Polina Prokopovich
Keyword(s):  
Applied Load ◽  
Cost Effective ◽  
Constant Load ◽  
Hydraulic Permeability ◽  
Frequency Dependent ◽  
Shear Moduli ◽  
Tissue Replacement ◽  
Cost Effective Approach ◽  
The Impact

AbstractDespite the well-established dependence of cartilage mechanical properties on the frequency of the applied load, most research in the field is carried out in either load-free or constant load conditions because of the complexity of the equipment required for the determination of time-dependent properties. These simpler analyses provide a limited representation of cartilage properties thus greatly reducing the impact of the information gathered hindering the understanding of the mechanisms involved in this tissue replacement, development and pathology. More complex techniques could represent better investigative methods, but their uptake in cartilage research is limited by the highly specialised training required and cost of the equipment. There is, therefore, a clear need for alternative experimental approaches to cartilage testing to be deployed in research and clinical settings using more user-friendly and financial accessible devices. Frequency dependent material properties can be determined through rheometry that is an easy to use requiring a relatively inexpensive device; we present how a commercial rheometer can be adapted to determine the viscoelastic properties of articular cartilage. Frequency-sweep tests were run at various applied normal loads on immature, mature and trypsinased (as model of osteoarthritis) cartilage samples to determine the dynamic shear moduli (G*, G′ G″) of the tissues. Moduli increased with increasing frequency and applied load; mature cartilage had generally the highest moduli and GAG depleted samples the lowest. Hydraulic permeability (KH) was estimated from the rheological data and decreased with applied load; GAG depleted cartilage exhibited higher hydraulic permeability than either immature or mature tissues. The rheometer-based methodology developed was validated by the close comparison of the rheometer-obtained cartilage characteristics (G*, G′, G″, KH) with results obtained with more complex testing techniques available in literature. Rheometry is relatively simpler and does not require highly capital intensive machinery and staff training is more accessible; thus the use of a rheometer would represent a cost-effective approach for the determination of frequency-dependent properties of cartilage for more comprehensive and impactful results for both healthcare professional and R&D.

Studies on Mechanical and Thermal Properties of Epoxy Resin Modified by Fluorine-Containing Silicone

2013 ◽  
Vol 401-403 ◽  
pp. 713-716
Author(s):  
Cheng Fang ◽  
Dong Bo Guan ◽  
Wei Guo Yao ◽  
Shou Jun Wang ◽  
Hui An
Keyword(s):  
Glass Transition ◽  
Thermal Properties ◽  
Epoxy Resin ◽  
Bending Strength ◽  
Mechanical And Thermal Properties ◽  
Curing Agent ◽  
Epoxy System ◽  
Resin Curing ◽  
The Impact ◽  
Modified Epoxy

The epoxy resin was modified with the mixture of α,ω-dihydroxy poly-(3,3,3-trifluoropropyl) siloxane (PTFPMS), KH560 and stannous octoate. KH560 can react with PTFPMS and also epoxy resin curing agent. The two reactions were characterized by FI-IR. The modified epoxy resin was characterized by FI-IR. The result showed that fluorine-containing silicone had been successfully introduced into the epoxy system. The mechanical and thermal properties of the modified epoxy resin were analyzed. The results showed that with the increase of PTFPMS the impact strength of epoxy resin increased, hardness and bending strength correspondingly reduced, slight decrease in the glass transition temperature.

Sign in / Sign up

Export Citation Format

Share Document