Superplastic compression, microstructural analysis and mechanical properties of a fine grain three-phase alumina–zirconia–mullite ceramic composite

2005 ◽  
Vol 410-411 ◽  
pp. 134-139 ◽  
Author(s):  
Tiandan Chen ◽  
Martha L. Mecartney
Keyword(s):  
Mechanical Properties ◽  
Ceramic Composite ◽  
Microstructural Analysis ◽  
Mullite Ceramic ◽  
Fine Grain ◽  
Three Phase

Microstructures and Mechanical Properties of B4C-TiB2 Composite Prepared by Hot Pressure Sintering

2010 ◽  
Vol 434-435 ◽  
pp. 50-53 ◽  
Author(s):  
Xin Yan Yue ◽  
Shu Mao Zhao ◽  
Liang Yu ◽  
Hong Qiang Ru
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Microstructural Analysis ◽  
Crack Deflection ◽  
Second Phase ◽  
Fine Grain ◽  
Pull Out ◽  
Microstructures And Mechanical Properties

B4C-TiB2 composite was prepared using hot pressure sintering. The microstructures and mechanical properties of the B4C-TiB2 composite were investigated. The B4C-TiB2 composite with 43 mass % TiB2 showed the optimized properties. The relative density, hardness, flexural strength and fracture toughness of that were 98.2 %, 25.9 GPa, 458 MPa and 8.7 MPa•m1/2, respectively. A number of toughening mechanisms, including fine grain, crack deflection and grain pull-out, were observed during microstructural analysis of the composite. The fracture mode of the B4C-TiB2 composite was greatly affected by the existence of the second phase of TiB2.

Grain-Boundary Sliding in a Superplastic Three-Phase Alumina-Zirconia-Mullite Ceramic Composite

2011 ◽  
Vol 94 (7) ◽  
pp. 2171-2180 ◽  
Author(s):  
Christopher M. Hoo ◽  
Danju Men ◽  
Lili Taherabadi ◽  
Martha L. Mecartney
Keyword(s):  
Grain Boundary ◽  
Ceramic Composite ◽  
Grain Boundary Sliding ◽  
Mullite Ceramic ◽  
Three Phase ◽  
Boundary Sliding

Effects of bottom plate in friction stir welding of AA6061-T6

2020 ◽  
Vol 118 (1) ◽  
pp. 108
Author(s):  
M.A. Vinayagamoorthi ◽  
M. Prince ◽  
S. Balasubramanian
Keyword(s):  
Mechanical Properties ◽  
Axial Load ◽  
Weld Zone ◽  
Welding Process ◽  
Bottom Plate ◽  
Welding Parameters ◽  
Nugget Zone ◽  
Friction Stir ◽  
Weld Joints ◽  
Fine Grain

The effects of 40 mm width bottom plates on the microstructural modifications and the mechanical properties of a 6 mm thick FSW AA6061-T6 joint have been investigated. The bottom plates are placed partially at the weld zone to absorb and dissipate heat during the welding process. An axial load of 5 to 7 kN, a rotational speed of 500 rpm, and a welding speed of 50 mm/min are employed as welding parameters. The size of the nugget zone (NZ) and heat-affected zone (HAZ) in the weld joints obtained from AISI 1040 steel bottom plate is more significant than that of weld joints obtained using copper bottom plate due to lower thermal conductivity of steel. Also, the weld joints obtained using copper bottom plate have fine grain microstructure due to the dynamic recrystallization. The friction stir welded joints obtained with copper bottom plate have exhibited higher ductility of 8.9% and higher tensile strength of 172 MPa as compared to the joints obtained using a steel bottom plate.

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

scholarly journals A Generalized Approach for Evaluating the Mechanical Properties of Polymer Nanocomposites Reinforced with Spherical Fillers

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 830
Author(s):  
Julio Cesar Martinez-Garcia ◽  
Alexandre Serraïma-Ferrer ◽  
Aitor Lopeandía-Fernández ◽  
Marco Lattuada ◽  
Janak Sapkota ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymeric Nanocomposites ◽  
Mechanical Reinforcement ◽  
Future Studies ◽  
Three Phase ◽  
Theoretical Predictions ◽  
Filler Network ◽  
New Research ◽  
Good Agreement ◽  
Research Avenue

In this work, the effective mechanical reinforcement of polymeric nanocomposites containing spherical particle fillers is predicted based on a generalized analytical three-phase-series-parallel model, considering the concepts of percolation and the interfacial glassy region. While the concept of percolation is solely taken as a contribution of the filler-network, we herein show that the glassy interphase between filler and matrix, which is often in the nanometers range, is also to be considered while interpreting enhanced mechanical properties of particulate filled polymeric nanocomposites. To demonstrate the relevance of the proposed generalized equation, we have fitted several experimental results which show a good agreement with theoretical predictions. Thus, the approach presented here can be valuable to elucidate new possible conceptual routes for the creation of new materials with fundamental technological applications and can open a new research avenue for future studies.

scholarly journals Effect of Sm Doping on the Microstructure, Mechanical Properties and Shape Memory Effect of Cu-13.0Al-4.0Ni Alloy

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4007
Author(s):  
Qimeng Zhang ◽  
Bo Cui ◽  
Bin Sun ◽  
Xin Zhang ◽  
Zhizhong Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Compressive Fracture ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Face Centered

The effects of rare earth element Sm on the microstructure, mechanical properties, and shape memory effect of the high temperature shape memory alloy, Cu-13.0Al-4.0Ni-xSm (x = 0, 0.2 and 0.5) (wt.%), are studied in this work. The results show that the Sm addition reduces the grain size of the Cu-13.0Al-4.0Ni alloy from millimeters to hundreds of microns. The microstructure of the Cu-13.0Al-4.0Ni-xSm alloys are composed of 18R and a face-centered cubic Sm-rich phase at room temperature. In addition, because the addition of the Sm element enhances the fine-grain strengthening effect, the mechanical properties and the shape memory effect of the Cu-13.0Al-4.0Ni alloy were greatly improved. When x = 0.5, the compressive fracture stress and the compressive fracture strain increased from 580 MPa, 10.5% to 1021 MPa, 14.8%, respectively. When the pre-strain is 10%, a reversible strain of 6.3% can be obtained for the Cu-13.0Al-4.0Ni-0.2Sm alloy.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals Enhancement of Mechanical Properties and Porosity of Concrete Using Steel Slag Coarse Aggregate

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2865
Author(s):  
Md Jihad Miah ◽  
Md. Munir Hossain Patoary ◽  
Suvash Chandra Paul ◽  
Adewumi John Babafemi ◽  
Biranchi Panda
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Steel Slag ◽  
Physical And Mechanical Properties ◽  
Length Change ◽  
Sustainable Building ◽  
Burnt Clay ◽  
Lower Porosity ◽  
Furnace Steel

This paper investigates the possibility of utilizing steel slags produced in the steelmaking industry as an alternative to burnt clay brick aggregate (BA) in concrete. Within this context, physical, mechanical (i.e., compressive and splitting tensile strength), length change, and durability (porosity) tests were conducted on concrete made with nine different percentage replacements (0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% by volume of BA) of BA by induction of furnace steel slag aggregate (SSA). In addition, the chemical composition of aggregate through X-ray fluorescence (XRF) analysis and microstructural analysis through scanning electron microscopy (SEM) of aggregates and concrete were performed. The experimental results show that the physical and mechanical properties of concrete made with SSA were significantly higher than that of concrete made with BA. The compressive and tensile strength increased by 73% when SSA fully replaced BA. The expansion of concrete made with SSA was a bit higher than the concrete made with BA. Furthermore, a significant lower porosity was observed for concrete made with SSA than BA, which decreased by 40% for 100% SSA concrete than 100% BA concrete. The relation between compressive and tensile strength with the porosity of concrete mixes are in agreement with the relationships presented in the literature. This study demonstrates that SSA can be used as a full replacement of BA, which is economical, conserves the natural aggregate, and is sustainable building material since burning brick produces a lot of CO2.

Sign in / Sign up

Export Citation Format

Share Document