CPW triple-fed ultra-wideband antenna with variable band-notch function

2014 ◽  
Vol 7 (6) ◽  
pp. 791-796 ◽  
Author(s):  
M. Naser-Moghadasi ◽  
L. Asadpor
Keyword(s):  
Printed Circuit Board ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Circuit Board ◽  
Manufacturing Cost ◽  
Radiation Patterns ◽  
Desirable Feature ◽  
Planar Wave ◽  
Matched Impedance ◽  
Uwb Applications

A small and compact ultra-wideband (UWB) aperture antenna with extended band-notched design is proposed. The antenna is composed of a rectangular aperture on ground plane of a printed circuit board and a fork-like exciting stub. The presented co-planar wave guide triple-fed antenna is easy to be applied with RF and microwave circuitry for low manufacturing cost. The antenna is successfully designed, implemented, and measured. A compact aperture area of 12.5 × 23 mm2 is acquired with promising performances, including broadband matched impedance and stable radiation patterns. The correlation between the mode-based field distributions and radiation patterns is discussed. Extended from the proposed antenna, one advanced band-notched (5–6 GHz) designs are also presented as a desirable feature for UWB applications.

Compact Design of an UWB Antenna with Dual Band-Notched Characteristic

2012 ◽  
Vol 195-196 ◽  
pp. 13-16
Author(s):  
Wen Bo Zeng ◽  
Jia Zhao ◽  
Bao Zhong Ke ◽  
Qi Qi Wu
Keyword(s):  
Frequency Band ◽  
Printed Circuit Board ◽  
Coplanar Waveguide ◽  
Impedance Matching ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Circuit Board ◽  
Dual Band ◽  
Uwb Antenna ◽  
Compact Design

An ultra-wideband (UWB) printed antenna with dual band-notched characteristic is presented in this paper. The proposed antenna is composed of a semi-circular patch fed by a tapered coplanar waveguide (CPW) and an unclosed ground plane, which are printed onto the same side of a FR4 printed circuit board (PCB) with an overall size of 30 mm × 30 mm × 1.5 mm. By embedding a simple arc-shaped slot in the patch and adding a T-shaped strip on the top of the patch, two notched frequency bands for rejection of WiMAX and WLAN system can be realized. The characteristics of the proposed antenna are investigated by using the software HFSS and validated experimentally, both simulated and measured results show that the proposed antenna prototype achieves good impedance matching over an frequency band from 2.1011.40 GHz for VSWR2 with two notched bands over the frequency range of 5-5.95 GHz and 3.1-3.9 GHz. Furthermore, a relatively stable gain and suitable radiation patterns are also achieved in both lower and upper UWB frequency band.

scholarly journals DESIGN OF ULTRAWIDEBAND MONOPOLE ANTENNA WITH MINIMUM GROUND PLANE EFFECT

2014 ◽  
pp. 87-90
Author(s):  
PRAVEEN K P ◽  
T MARY NEEBHA
Keyword(s):  
Printed Circuit Board ◽  
Low Cost ◽  
Impedance Matching ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Circuit Board ◽  
Uwb Antenna ◽  
Printed Circuit ◽  
Feed Line ◽  
Simple Geometry

A Planar ultra wideband antenna design is analyzed for increased impedance matching in the Ultrawideband (UWB) range (3.1GHz to 10.6GHz). Also the effect of the ground plane is minimized by cutting slot on the ground plane. Impedance matching of Ultrawideband (UWB) antenna can be improved by introducing simple microstrip transitions between the 50-ohm feed line and the printed disc. In this paper a dual step feed is proposed between the feed line and radiator. It also offers a very simple geometry suitable for low cost fabrication and straightforward printed circuit board integration. Here triangle slot is provided on the ground plane in order to reduce the ground plane effect. The radiator used here is elliptical disc.

Design of a compact UWB antenna with a partial ground plane on epoxy woven glass material

2017 ◽  
Vol 24 (1) ◽  
pp. 73-79
Author(s):  
Md. Moinul Islam ◽  
Mohammad Tariqul Islam ◽  
Mohammad Rashed Iqbal Faruque ◽  
Rabah W. Aldhaheri ◽  
Md. Samsuzzaman
Keyword(s):  
Dielectric Material ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Design Parameters ◽  
Uwb Antenna ◽  
Glass Material ◽  
Measurement Results ◽  
Good Term ◽  
Parametric Analyses ◽  
Uwb Applications

AbstractA compact ultra-wideband (UWB) antenna is presented in this paper with a partial ground plane on epoxy woven glass material. The study is discussed to comprehend the effects of various design parameters with explicit parametric analyses. The overall antenna dimension is 0.22×0.26×0.016 λ. A prototype is made on epoxide woven glass fabric dielectric material of 1.6 mm thickness. The measured results point out that the reported antenna belongs to a wide bandwidth comprehending from 3 GHz to more than 11 GHz with VSWR<2. It has a peak gain of 5.52 dBi, where 3.98 dBi is the average gain. Nearly omnidirectional radiation patterns are observed within the operating frequency bands. A good term exists between simulation and measurement results, which lead the reported antenna to be an appropriate candidate for UWB applications.

scholarly journals A Study on the Radiated Susceptibility of Printed Circuit Boards and the Effects of Via Fencing

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 539
Author(s):  
Ryan P. Tortorich ◽  
William Morell ◽  
Elizabeth Reiner ◽  
William Bouillon ◽  
Jin-Woo Choi
Keyword(s):  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Ground Plane ◽  
Circuit Board ◽  
Electronic Systems ◽  
Coupling Mechanism ◽  
Electromagnetic Modeling ◽  
Printed Circuit ◽  
Edge Radiation ◽  
Area Of Concern

Because modern electronic systems are likely to be exposed to high intensity radiated fields (HIRF) environments, there is growing interest in understanding how electronic systems are affected by such environments. Backdoor coupling in particular is an area of concern for all electronics, but there is limited understanding about the mechanisms behind backdoor coupling. In this work, we present a study on printed circuit board (PCB) backdoor coupling and the effects of via fencing. Existing work focuses on ideal stackups and indicates that edge radiation is significantly reduced by via fencing. In this study, both full wave electromagnetic modeling and experimental verification are used to investigate both ideal and practical PCB stackups. In the ideal scenario, we find that via fencing substantially reduces coupling, which is consistent with prior work on emissions. In the practical scenario, we incorporate component footprints and traces which naturally introduce openings in the top ground plane. Both simulation and experimental data indicate that via fencing in the practical scenario does not substantially mitigate coupling, suggesting that PCB edge coupling is not the dominant coupling mechanism, even at varying angles of incidence and polarization.

scholarly journals A Circular Disc Microstrip Antenna with Dual Notch Band for GSM/Bluetooth and Extended UWB Applications

2018 ◽  
Vol 7 (2.16) ◽  
pp. 11
Author(s):  
Sanjeev Kumar ◽  
Ravi Kumar ◽  
Rajesh Kumar Vishwakarma
Keyword(s):  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
Circular Disc ◽  
Ultra Wideband ◽  
Resonant Circuit ◽  
Frequency Range ◽  
Notch Band ◽  
Uwb Applications ◽  
Ku Band

A microstrip antenna with a circular disc design and modified ground is proposed in this paper. Circular shapes of different size have been slotted out from the radiating patch for achieving extended ultra wideband (UWB) with GSM/Bluetooth bands with maximum bandwidth of 17.7 GHz (0.88-18.6 GHz). Further, characteristic of dual notch band is achieved, when a combination of T and L-shaped slots are etched into the circular disc and ground plane respectively. Change in length of slots is controlling the notch band characteristics. The proposed antenna has rejection bandwidth of 1.3-2.2 GHz (LTE band), 3.2-3.9 GHz (WiMAX band) and 5.2-6.1 GHz (WLAN band) respectively. It covers the frequency range of 0.88-18.5 GHz with the VSWR of less than 2. Also, an equivalent parallel resonant circuit has been demonstrated for band notched frequencies of the designed antenna. The gain achieved by the proposed antenna is 6.27 dBi. This antenna has been designed, investigated and fabricated for GSM, Bluetooth, UWB, X and Ku band applications. The stable gain including H & E-plane radiation pattern with good directivity and omnidirectional behavior is achieved by the proposed antenna. Measured bandwidths are 0.5 GHz, 0.8 GHz, 1.1 GHz and 11.7 GHz respectively. 

Low-profile U-shaped DRA for ultra-wideband applications

2016 ◽  
Vol 9 (3) ◽  
pp. 621-627 ◽  
Author(s):  
Idris Messaoudene ◽  
Tayeb A. Denidni ◽  
Abdelmadjid Benghalia
Keyword(s):  
Dielectric Resonator ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
Wide Bandwidth ◽  
Operating Band ◽  
Low Profile ◽  
Measurement Results

In this paper, a microstrip-fed U-shaped dielectric resonator antenna (DRA) is simulated, designed, and fabricated. This antenna, in its simple configuration, operates from 5.45 to 10.8 GHz. To enhance its impedance bandwidth, the ground plane is first modified, which leads to an extended bandwidth from 4 to 10.8 GHz. Then by inserting a rectangular metallic patch inside the U-shaped DRA, the bandwidth is increased more to achieve an operating band from 2.65 to 10.9 GHz. To validate these results, an experimental antenna prototype is fabricated and measured. The obtained measurement results show that the proposed antenna can provide an ultra-wide bandwidth and a symmetric bidirectional radiation patterns. With these features, the proposed antenna is suitable for ultra-wideband applications.

scholarly journals A Series-Fed Linear Substrate-Integrated Dielectric Resonator Antenna Array for Millimeter-Wave Applications

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Ke Gong ◽  
Xue Hui Hu ◽  
Peng Hu ◽  
Bing Jie Deng ◽  
You Chao Tu
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Dielectric Resonator ◽  
Return Loss ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
Feeding Structure ◽  
Broadside Radiation

A series-fed linear substrate-integrated dielectric resonator antenna array (SIDRAA) is presented for millimeter-wave applications, in which the substrate-integrated dielectric resonator antenna (SIDRA) elements and the feeding structure can be codesigned and fabricated using the same planar process. A prototype 4 × 1 SIDRAA is designed at Ka-band and fabricated with a two-layer printed circuit board (PCB) technology. Four SIDRAs are implemented in the Rogers RT6010 substrate using the perforation technique and fed by a compact substrate-integrated waveguide (SIW) through four longitudinal coupling slots within the Rogers RT5880 substrate. The return loss, radiation patterns, and antenna gain were experimentally studied, and good agreement between the measured and simulated results is observed. The SIDRAA example provides a bandwidth of about 10% around 34.5 GHz for 10 dB return loss and stable broadside radiation patterns with the peak gain of 10.5–11.5 dBi across the band.

Compact UWB monopole antenna with reconfigurable band-notch characteristics

2019 ◽  
Vol 12 (3) ◽  
pp. 252-258 ◽  
Author(s):  
Liping Han ◽  
Jing Chen ◽  
Wenmei Zhang
Keyword(s):  
Ground Plane ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Dual Band ◽  
Radiation Patterns ◽  
Pin Diodes ◽  
Notch Band ◽  
Rectangular Patch ◽  
Compact Size ◽  
Defected Ground Plane

AbstractA compact ultra-wideband (UWB) monopole antenna with reconfigurable band-notch characteristics is demonstrated in this paper. It is comprised of a modified rectangular patch and a defected ground plane. The band-notch property in the WiMAX and WLAN bands is achieved by etching an open-ended slot on the radiating patch and an inverted U-shaped slot on the ground plane, respectively. To obtain the reconfigurable band-notch performance, two PIN diodes are inserted in the slots, and then the notch-band can be switched by changing the states of the PIN diodes. The antenna has a compact size of 0.47 λ1 × 0.27 λ1. The simulated and measured results indicate that the antenna can operate at a UWB mode, two single band-notch modes, and a dual band-notch mode. Moreover, stable radiation patterns are obtained.

A Design of Printed Inverted-F Antenna for RFID Tag at 5.8 GHz

2013 ◽  
Vol 427-429 ◽  
pp. 1293-1296
Author(s):  
Yan Zhong Yu ◽  
Ji Zhen Ni ◽  
Xian Hui Li
Keyword(s):  
High Frequency ◽  
Printed Circuit Board ◽  
Ground Plane ◽  
Simulation Software ◽  
Circuit Board ◽  
Electromagnetic Simulation ◽  
Antenna Structure ◽  
Rfid Tag ◽  
Printed Circuit ◽  
Substrate Layer

A printed inverted-F antenna for RFID tag at 5.8 GHz is designed in this paper. The antenna structure consists of an inverted-F patch, a substrate layer, and a ground plane. To reduce costs, the FR4 is selected as the material of substrate layer, which is used commonly in PCB (Printed Circuit Board). Its relative permittivity is 4.4 and a loss tangent is 0.02. The inverted-F patch and ground plane are laid on/under the substrate layer respectively. The designed antenna is modeled, simulated and optimized by using HFSS (high frequency electromagnetic simulation software). Simulation results demonstrate that the printed inverted-F antenna can satisfy the requirements of RFID Tag applications.

Sign in / Sign up

Export Citation Format

Share Document