Proquinoidal-Conjugated Polymer as an Effective Strategy for the Enhancement of Electrical Conductivity and Thermoelectric Properties

2019 ◽  
Vol 31 (20) ◽  
pp. 8543-8550 ◽  
Author(s):  
Teck Lip Dexter Tam ◽  
Chee Koon Ng ◽  
Siew Lay Lim ◽  
Erol Yildirim ◽  
Jieun Ko ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Thermoelectric Properties ◽  
Conjugated Polymer ◽  
Effective Strategy

The Influence of Silicon Dopant and Processing on Thermoelectric Properties of B4C Ceramics

1998 ◽  
Vol 545 ◽  
Author(s):  
Ke-Feng Cai ◽  
Ce-Wen Nan ◽  
Xin-Min Min
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Hot Pressing ◽  
Figure Of Merit ◽  
Room Temperature ◽  
A Value ◽  
Si Doped

AbstractB4C ceramics doped with various content of Si (0 to 2.03 at%) are prepared via hot pressing. The composition and microstructure of the ceramics are characterized by means of XRD and EPMA. Their electrical conductivity and Seebeck coefficient of the samples are measured from room temperature up to 1500K. The electrical conductivity increases with temperature, and more rapidly after 1300K; the Seebeck coefficient of the ceramics also increases with temperature and rises to a value of about 320μVK−1. The value of the figure of merit of Si-doped B4C rises to about 4 × 10−4K−1 at 1500K.

Band Structure and Thermoelectric Properties of Ni(x)Zn(1-x)Fe2O4

2021 ◽  
Vol 317 ◽  
pp. 28-34
Author(s):  
Joon Hoong Lim
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Band Structure ◽  
Seebeck Coefficient ◽  
Band Gap ◽  
Thermoelectric Properties ◽  
Xrd Analysis ◽  
Valence Band Maximum ◽  
Solid State Method ◽  
Ni Content

Thermoelectric materials has made a great potential in sustainable energy industries, which enable the energy conversion from heat to electricity. The band structure and thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 have been investigated. The bulk pellets were prepared from analytical grade ZnO, NiO and Fe2O3 powder using solid-state method. It was possible to obtain high thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 by controlling the ratios of dopants and the sintering temperature. XRD analysis showed that the fabricated samples have a single phase formation of cubic spinel structure. The thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 pellets improved with increasing Ni. The electrical conductivity of Ni(x)Zn(1-x)Fe2O4 pellets decreased with increasing Ni content. The electrical conductivity of Ni(x)Zn(1-x)Fe2O4 (x = 0.0) is (0.515 x10-3 Scm-1). The band structure shows that ZnxCu1-xFe2O4 is an indirect band gap material with the valence band maximum (VBM) at M and conduction band minimum (CBM) at A. The band gap of Ni(x)Zn(1-x)Fe2O4 increased with increasing Ni content. The increasing band gap correlated with the lower electrical conductivity. The thermal conductivity of Ni(x)Zn(1-x)Fe2O4 pellets decreased with increasing Ni content. The presence of Ni served to decrease thermal conductivity by 8 Wm-1K-1 over pure samples. The magnitude of the Seebeck coefficient for Ni(x)Zn(1-x)Fe2O4 pellets increased with increasing amounts of Ni. The figure of merit for Ni(x)Zn(1-x)Fe2O4 pellets and thin films was improved by increasing Ni due to its high Seebeck coefficient and low thermal conductivity.

scholarly journals Preparation and Thermoelectric Properties of Graphite/poly(3,4-ethyenedioxythiophene) Nanocomposites

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2849 ◽  
Author(s):  
Yong Du ◽  
Haixia Li ◽  
Xuechen Jia ◽  
Yunchen Dou ◽  
Jiayue Xu ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Oxidative Polymerization ◽  
Polymerization Process ◽  
Measurement Temperature ◽  
Temperature Range ◽  
Different Content

Graphite/poly(3,4-ethyenedioxythiophene) (PEDOT) nanocomposites were prepared by an in-situ oxidative polymerization process. The electrical conductivity and Seebeck coefficient of the graphite/PEDOT nanocomposites with different content of graphite were measured in the temperature range from 300 K to 380 K. The results show that as the content of graphite increased from 0 to 37.2 wt %, the electrical conductivity of the nanocomposites increased sharply from 3.6 S/cm to 80.1 S/cm, while the Seebeck coefficient kept almost the same value (in the range between 12.0 μV/K to 15.1 μV/K) at 300 K, which lead to an increased power factor. The Seebeck coefficient of the nanocomposites increased from 300 K to 380 K, while the electrical conductivity did not substantially depend on the measurement temperature. As a result, a power factor of 3.2 μWm−1 K−2 at 380 K was obtained for the nanocomposites with 37.2 wt % graphite.

scholarly journals Semi-metallic, strong and stretchable wet-spun conjugated polymer microfibers

2015 ◽  
Vol 3 (11) ◽  
pp. 2528-2538 ◽  
Author(s):  
Jian Zhou ◽  
Er Qiang Li ◽  
Ruipeng Li ◽  
Xuezhu Xu ◽  
Isaac Aguilar Ventura ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Conjugated Polymer ◽  
High Performance ◽  
Wet Spinning ◽  
Hot Drawing ◽  
Polymer Microfibers

High-performance conjugated polymer microfibers were fabricated via wet-spinning followed by hot-drawing. With a combination of solvent doping and de-doping, we achieved a record electrical conductivity of 2804 S cm−1.

LOW TEMPERATURE THERMOELECTRIC PROPERTIES AND AGING PHENOMENA OF NANOSTRUCTURED p-TYPE Bi2-XSbXTe3 (x = 1.46, 1.48, 1.52 AND 1.55)

2013 ◽  
Vol 06 (05) ◽  
pp. 1340008 ◽  
Author(s):  
DALE HITCHCOCK ◽  
YEN-LIANG LIU ◽  
YUFEI LIU ◽  
TERRY M. TRITT ◽  
JIAN HE ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Low Temperature ◽  
Thermoelectric Properties ◽  
Optimal Composition ◽  
Ambient Conditions ◽  
Bulk Materials ◽  
The Past ◽  
Aging Phenomena ◽  
P Type ◽  
Cold Pressed

Over the past decade the widely used p-type ( Bi 2-x Sb x) Te 3 bulk thermoelectric materials have been subject to various nanostructuring processes for higher thermoelectric performance. However, these nanostructuring processing were conducted on compositions optimized for bulk materials (x ~ 1.52–1.55). This leads to the question of whether the optimal composition for bulk materials is the same for their nanoscale counterparts. In this work we hydrothermally grew Bi 2-x Sb x Te 3 nanopowders (nominally, x = 1.46, 1.48, 1.52 and 1.55) and measured their thermoelectric properties on cold-pressed vacuum-sintered pellets (74–78% of the theoretical density) below 300 K. The measurements were conducted 18 months apart to probe the aging phenomena, with the samples stored in ambient conditions. We have found that (i) the peak of thermopower shifts to lower temperatures upon nanostructuring but it shifts back to higher temperatures upon aging; (ii) the electrical conductivity degrades by a factor of 1.5–2.3 upon aging while the temperature dependence is largely retained; and (iii) the ZT of freshly made samples is sensitive to the x value, a maximum ZT ~ 1.25(~ 0.62) at ~ 270 K (~ 255 K) was attained in the freshly made sample x = 1.55(x = 1.46), respectively; while the ZT of aged samples is significantly lowered by a factor of 2–4 but lesser x-dependent. These observations have been discussed in the context of charge buildup and compensation at grain boundaries.

scholarly journals Effect of band structure adjustment based of Cu site on the thermoelectric properties of BiCuSeO

2021 ◽  
Author(s):  
Bo Feng
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Effective Mass ◽  
Valence Band ◽  
Thermoelectric Properties ◽  
Density Of States ◽  
First Principles Calculation ◽  
Temperature Range ◽  
Ti Doping

Abstract The effect of Ti doped at Cu site on the thermoelectric properties of BiCuSeO was studied by experimental method and first principles calculation. The results show that Ti doping can cause the lattice contraction and decrease the lattice constant. Ti doping can increase the band gap and lengthen the Cu/Ti-Se bond, resulting in the decrease of carrier concentration. Ti doping can reduce the effective mass and the Bi-Se bond length, correspondingly improve the carrier mobility. Ti doping can decrease the density of states of Cu-3d and Se-4p orbitals at the top of valence band, but Ti-4p orbitals can obviously increase the density of states at the top of valence band and finally increase the electrical conductivity in the whole temperature range. With the decrease of effective mass, Ti doping would reduce the Seebeck coefficient, but the gain effect caused by the increase of electrical conductivity is more than the benefit reduction effect caused by the decrease of Seebeck coefficient, and the power factor shows an upward trend. Ti doping can reduce Young's modulus, lead to the increase of defect scattering and strain field, correspondingly reduce the lattice thermal conductivity and total thermal conductivity. It is greatly increased for the ZT values in the middle and high temperature range, with the highest value of 1.04 at 873 K.

Thermoelectric Properties of n-type (Bi2Se3)x(Bi2Te3)1-x Crystals Prepared by Zone Melting

2008 ◽  
Vol 368-372 ◽  
pp. 547-549
Author(s):  
Jun Jiang ◽  
Ya Li Li ◽  
Gao Jie Xu ◽  
Ping Cui ◽  
Li Dong Chen
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Zone Melting ◽  
Chemical Compositions ◽  
Melting Method ◽  
Temperature Range

In the present study, n-type (Bi2Se3)x(Bi2Te3)1-x crystals with various chemical compositions were fabricated by the zone melting method. Thermoelectric properties, including Seebeck coefficient (α), electrical conductivity (σ) and thermal conductivity (κ), were measured in the temperature range of 300-500 K. The influence of the variations of Bi2Te3 and Bi2Se3 content on thermoelectric properties was studied. The increase of Bi2Se3 content (x) caused an increase in carrier concentration and thus an increase of σ and a decrease of α. The maximum figure of merit (ZT = α2σT/κ) of 0.87 was obtained at about 325 K for the composition of 93%Bi2Te3-7%Bi2Se3 with doping TeI4.

Effect of Thermal Treatment on Thermoelectric Properties of Extruded TiO2 Ceramics

2014 ◽  
Vol 604 ◽  
pp. 249-253 ◽  
Author(s):  
Agnese Pura ◽  
Janis Locs ◽  
Liga Berzina-Cimdina
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Thermal Treatment ◽  
Seebeck Coefficient ◽  
Heating Rate ◽  
Thermoelectric Properties ◽  
Sintering Temperature ◽  
Extrusion Process ◽  
Vacuum Heat Treatment ◽  
Treatment Conditions

TiO2samples were obtained by extrusion process, sintered in air at 1000 °C, 1100 °C, 1200°C and 1300 °C and, afterwards, thermally treated under vacuum conditions at 1250 °C for 1 hour applying two different heating/cooling rates (2 °C/min and 5 °C/min). It was found that thermal treatment conditions substantially affected thermoelectric properties of the samples. Increasing sintering temperature, during the sample thermal treatment in air, the electrical conductivity of the specimens increased, while Seebeck coefficient decreased. With an increase in the heating rate during the vacuum heat treatment of the samples, the electrical conductivity of the samples decreased, while Seebeck coefficient increased.

Sign in / Sign up

Export Citation Format

Share Document