scholarly journals Dual-functional ultraviolet photodetector with graphene electrodes on AlGaN/GaN heterostructure

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Bhishma Pandit ◽  
E. Fred Schubert ◽  
Jaehee Cho
Keyword(s):  
Bias Voltage ◽  
Threshold Voltage ◽  
Response Times ◽  
Fast Response ◽  
Dual Functional ◽  
Photocurrent Generation ◽  
Recovery Times ◽  
Slow Rise ◽  
Generation Mechanisms ◽  
Gan Heterostructure

AbstractA dual-functional ultraviolet (UV) photodetector with a large UV-to-visible rejection ratio is presented, in which interdigitated finger-type two-dimensional graphene electrodes are introduced to an AlGaN/GaN heterostructure. Two photocurrent generation mechanisms of photovoltaic and photoconductive dominances coexist in the device. The dominance of the mechanisms changes with the induced bias voltage. Below a threshold voltage, the device showed fairly low responsivities but fast response times, as well as a constant photocurrent against the induced bias. However, the opposite characteristics appeared with high bias voltage. Specifically, above the threshold voltage, the device showed high responsivities with additional gain, but slow rise and recovery times. For instance, the responsivity of 10.9 A/W was observed with the gain of 760 at the induced bias voltage of 5 V. This unique multifunctionality enabled by the combination of an AlGaN/GaN heterostructure with graphene electrodes facilitates the development of a single device that can achieve multiple purposes of photodetection.

Fast formaldehyde gas sensing response properties of ultrathin SnO2 nanosheets

RSC Advances ◽  
2015 ◽  
Vol 5 (126) ◽  
pp. 104574-104581 ◽  
Author(s):  
Hai Yu ◽  
Tianye Yang ◽  
Rui Zhao ◽  
Bingxin Xiao ◽  
Zhifang Li ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Response Times ◽  
Fast Response ◽  
Response Properties ◽  
Recovery Times

The ultrathin SnO2 nanosheet sensors detect formaldehyde, and show very fast response times (<1 s) and recovery times (6 s).

Nanostructure of semiconductor quantum dots in a borosilicate glass matrix by complementary use of HREM and AEM

1990 ◽  
Vol 48 (4) ◽  
pp. 728-729
Author(s):  
M.J. Kim ◽  
L.C. Liu ◽  
S.H. Risbud ◽  
R.W. Carpenter
Keyword(s):  
Quantum Dots ◽  
Borosilicate Glass ◽  
Glass Matrix ◽  
Optical Switching ◽  
Response Times ◽  
Fast Response ◽  
Processing Technique ◽  
Internal Stresses ◽  
Electron Hole ◽  
Spatial Dimensions

When the size of a semiconductor is reduced by an appropriate materials processing technique to a dimension less than about twice the radius of an exciton in the bulk crystal, the band like structure of the semiconductor gives way to discrete molecular orbital electronic states. Clusters of semiconductors in a size regime lower than 2R {where R is the exciton Bohr radius; e.g. 3 nm for CdS and 7.3 nm for CdTe) are called Quantum Dots (QD) because they confine optically excited electron- hole pairs (excitons) in all three spatial dimensions. Structures based on QD are of great interest because of fast response times and non-linearity in optical switching applications.In this paper we report the first HREM analysis of the size and structure of CdTe and CdS QD formed by precipitation from a modified borosilicate glass matrix. The glass melts were quenched by pouring on brass plates, and then annealed to relieve internal stresses. QD precipitate particles were formed during subsequent "striking" heat treatments above the glass crystallization temperature, which was determined by differential thermal analysis.

Compact and efficient gas diffusion electrodes based on nanoporous alumina membranes for microfuel cells and gas sensors

The Analyst ◽  
2020 ◽  
Vol 145 (1) ◽  
pp. 122-131 ◽  
Author(s):  
Wanda V. Fernandez ◽  
Rocío T. Tosello ◽  
José L. Fernández
Keyword(s):  
Response Times ◽  
Hydrogen Oxidation ◽  
Fast Response ◽  
Gas Diffusion ◽  
Limiting Current ◽  
Gas Diffusion Electrodes ◽  
Nanoporous Alumina ◽  
Alumina Membranes ◽  
Current Densities ◽  
Microfuel Cells

Gas diffusion electrodes based on nanoporous alumina membranes electrocatalyze hydrogen oxidation at high diffusion-limiting current densities with fast response times.

scholarly journals Tin Disulfide-Coated Microfiber for Humidity Sensing with Fast Response and High Sensitivity

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 648
Author(s):  
Aijie Liang ◽  
Jingyuan Ming ◽  
Wenguo Zhu ◽  
Heyuan Guan ◽  
Xinyang Han ◽  
...  
Keyword(s):  
Humidity Sensor ◽  
Small Diameter ◽  
High Sensitivity ◽  
Large Change ◽  
Small Variation ◽  
Response Speed ◽  
Fast Response ◽  
Tin Disulfide ◽  
Recovery Times ◽  
Response And Recovery

Breath monitoring is significant in assessing human body conditions, such as cardiac and pulmonary symptoms. Optical fiber-based sensors have attracted much attention since they are immune to electromagnetic radiation, thus are safe for patients. Here, a microfiber (MF) humidity sensor is fabricated by coating tin disulfide (SnS2) nanosheets onto the surface of MF. The small diameter (~8 μm) and the long length (~5 mm) of the MF promise strong interaction between guiding light and SnS2. Thus, a small variation in the relative humidity (RH) will lead to a large change in optical transmitted power. A high RH sensitivity of 0.57 dB/%RH is therefore achieved. The response and recovery times are estimated to be 0.08 and 0.28 s, respectively. The high sensitivity and fast response speed enable our SnS2-MF sensor to monitor human breath in real time.

scholarly journals FEM Simulation of Frequency-Selective Surface Based on Thermoelectric Bi-Sb Thin Films for THz Detection

Photonics ◽  
2021 ◽  
Vol 8 (4) ◽  
pp. 119
Author(s):  
Anastasiia Tukmakova ◽  
Ivan Tkhorzhevskiy ◽  
Artyom Sedinin ◽  
Aleksei Asach ◽  
Anna Novotelnova ◽  
...  
Keyword(s):  
Thin Films ◽  
Response Times ◽  
Fem Simulation ◽  
Film Surface ◽  
Frequency Selective Surface ◽  
Fast Response ◽  
Radiation Absorption ◽  
Thz Radiation ◽  
Frequency Filter ◽  
Frequency Selective

Terahertz (THz) filters and detectors can find a wide application in such fields as: sensing, imaging, security systems, medicine, wireless connection, and detection of substances. Thermoelectric materials are promising basis for THz detectors’ development due to their sensitivity to the THz radiation, possibility to be heated under the THz radiation and produce voltage due to Seebeck effect. Thermoelectric thin films of Bi-Sb solid solutions are semimetals/semiconductors with the band gap comparable with THz energy and with high thermoelectric conversion efficiency at room temperature. Detecting film surface can be transformed into a periodic frequency selective surface (FSS) that can operate as a frequency filter and increases the absorption of THz radiation. We report for the first time about the simulation of THz detector based on thermoelectric Bi-Sb thin-filmed frequency-selective surface. We show that such structure can be both detector and frequency filter. Moreover, it was shown that FSS design increases not only a heating due to absorption but a temperature gradient in Bi-Sb film by two orders of magnitude in comparison with continuous films. Local temperature gradients can reach the values of the order of 100 K·mm−1. That opens new perspectives for thin-filmed thermoelectric detectors’ efficiency increase. Temperature difference formed due to THz radiation absorption can reach values on the order of 1 degree. Frequency-transient calculations show the power dependence of film temperature on time with characteristic saturation at times around several ms. That points to the perspective of reaching fast response times on such structures.

Novel optical oxygen sensing by phosphorescence quenching of palladium porphyrin self-assembled film on alumina plate

2000 ◽  
Vol 04 (02) ◽  
pp. 179-184 ◽  
Author(s):  
YUTAKA AMAO ◽  
KEISUKE ASAI ◽  
ICHIRO OKURA
Keyword(s):  
Oxygen Pressure ◽  
Oxygen Sensor ◽  
Response Times ◽  
Oxygen Sensing ◽  
Fast Response ◽  
Phosphorescence Quenching ◽  
Highly Sensitive ◽  
Optical Oxygen Sensor ◽  
Self Assembled ◽  
Quenching By Oxygen

An optical oxygen sensor based on the phosphorescence quenching of palladium tetrakis(4-carboxyphenyl)porphyrin (PdTCPP) self-assembled film (SAM) on alumina plate was developed. The phosphorescence intensity of PdTCPP film decreased with increasing oxygen pressure, indicating that the film can be used as an optical oxygen-sensing device based on phosphorescence quenching by oxygen. The ratio I0/I100 as a sensitivity measure of the sensing film is estimated to be 17.7, showing that the film is a highly sensitive device for oxygen pressure. The film obeyed Stern–Volmer plots with a multisite model and possessed good operational stability and a fast response. Response times are 36 s for deoxygenated to oxygenated conditions and 148 s for the reverse conditions.

Evaluation Humidity Sensing Properties of Graphene/HS-TiO2 Nanocomposites

2021 ◽  
Vol 21 (10) ◽  
pp. 5143-5149
Author(s):  
Zhen Zhu ◽  
Wang-De Lin
Keyword(s):  
Room Temperature ◽  
Response Times ◽  
Sol Gel ◽  
Hollow Spheres ◽  
High Sensitivity ◽  
Humidity Sensing ◽  
X Ray ◽  
Transmission Electron ◽  
Recovery Times ◽  
Relative Humidity Range

This paper reports on a nanocomposite synthesized by sol–gel procedure comprising graphene sheets with hollow spheres of titanium dioxide (G/HS-TiO2) with varying weight percentages of graphene for the purpose of humidity sensors. The surface morphology of the nanocomposite was characterized using transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). The structural properties were examined using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). The response to 12–80% RH at room temperature exhibited sensitivity (S = 135). However, the relative humidity range of 12–90% at room temperature exhibited higher sensitivity (S = 557). Sensors fabricated using the proposed nanocomposite exhibited high sensitivity to humidity, high stability, rapid response times, and rapid recovery times with hysteresis error of less than 1.79%. These results demonstrate the outstanding potential of his material for the monitoring of atmospheric humidity. This study also sought to elucidate the mechanisms underlying humidity sensing performance.

scholarly journals Capacitive type Humidity Sensor based on PANI decorated Cu-Zns Porous Micropshere

2020 ◽  
Author(s):  
Jolly Bhadra ◽  
Hemalatha Parangusan ◽  
Zubair Ahmad ◽  
Shoaib Mallick ◽  
Farid Touati ◽  
...  
Keyword(s):  
Humidity Sensor ◽  
In Situ Polymerization ◽  
Fast Response ◽  
Polymerization Process ◽  
Average Response ◽  
Surface Absorption ◽  
Absorption Properties ◽  
Recovery Times ◽  
Response And Recovery

PANI coated Cu-ZnS porous microsphere structures have been synthesized by hydrothermal method and in-situ polymerization process. The synthesized composite is characterized by different techniques in order to study the structural, morphological and surface absorption properties. The experimental observation demonstrates that the PANI/1%Cu-ZnS composite has better sensitivity, fast response and good stability as compared to pure PANI and other PANI/CuZnS compositions. Finally, PANI/1% Cu-ZnS composite has been found to be optimized for the humidity sensors due to its well-distributed roughness, porosity and hydrophilicity. The average response and recovery times of the PANI/1% Cu-ZnS are found to be 42 s and 24 s, respectively, which outperform recent results.

scholarly journals Preparation of Powders Containing Sb, Ni, and O for the Design of a Novel CO and C3H8 Sensor

2021 ◽  
Vol 11 (20) ◽  
pp. 9536
Author(s):  
Jorge Alberto Ramírez-Ortega ◽  
José Trinidad Guillén-Bonilla ◽  
Alex Guillén-Bonilla ◽  
Verónica María Rodríguez-Betancourtt ◽  
Lorenzo Gildo-Ortiz ◽  
...  
Keyword(s):  
Response Times ◽  
High Capacity ◽  
Dynamic Tests ◽  
X Ray Diffraction ◽  
Wet Chemistry ◽  
Good Thermal Stability ◽  
Great Performance ◽  
Vis Spectroscopy ◽  
Recovery Times ◽  
Response And Recovery

In this work, powders of NiSb2O6 were synthesized using a simple and economical microwave-assisted wet chemistry method, and calcined at 700, 800, and 900 °C. It was identified through X-ray diffraction that the oxide is a nanomaterial with a trirutile-type structure and space group P42/mnm (136). UV–Vis spectroscopy measurements showed that the bandgap values were at ~3.10, ~3.14, and ~3.23 eV at 700, 800, and 900 °C, respectively. Using scanning electron microscopy (SEM), irregularly shaped polyhedral microstructures with a size of ~154.78 nm were observed on the entire material’s surface. The particle size was estimated to average ~92.30 nm at the calcination temperature of 900 °C. Sensing tests in static atmospheres containing 300 ppm of CO at 300 °C showed a maximum sensitivity of ~72.67. On the other hand, in dynamic atmospheres at different CO flows and at an operating temperature of 200 °C, changes with time in electrical resistance were recorded, showing a high response, stability, and repeatability, and good sensor efficiency during several operation cycles. The response times were ~2.77 and ~2.10 min to 150 and 200 cm3/min of CO, respectively. Dynamic tests in propane (C3H8) atmospheres revealed that the material improved its response in alternating current signals at two different frequencies (0.1 and 1 kHz). It was also observed that at 360 °C, the ability to detect propane flows increased considerably. As in the case of CO, NiSb2O6’s response in propane atmospheres showed very good thermal stability, efficiency, a high capacity to detect C3H8, and short response and recovery times at both frequencies. Considering the great performance in propane flows, a sensor prototype was developed that modulates the electrical signals at 360 °C, verifying the excellent functionality of NiSb2O6.

Sign in / Sign up

Export Citation Format

Share Document