scholarly journals Characterization of a new natural fiber extracted from Corypha taliera fruit

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Taslima Ahmed Tamanna ◽  
Shah Alimuzzaman Belal ◽  
Mohammad Abul Hasan Shibly ◽  
Ayub Nabi Khan
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Morphological Characteristics ◽  
Synthetic Fiber ◽  
X Ray Diffraction ◽  
Reinforced Composite ◽  
Potential Alternative

AbstractThis study deals with the determination of new natural fibers extracted from the Corypha taliera fruit (CTF) and its characteristics were reported for the potential alternative of harmful synthetic fiber. The physical, chemical, mechanical, thermal, and morphological characteristics were investigated for CTF fibers. X-ray diffraction and chemical composition characterization ensured a higher amount of cellulose (55.1 wt%) content and crystallinity (62.5%) in the CTF fiber. The FTIR analysis ensured the different functional groups of cellulose, hemicellulose, and lignin present in the fiber. The Scherrer’s equation was used to determine crystallite size 1.45 nm. The mean diameter, specific density, and linear density of the CTF fiber were found (average) 131 μm, 0.86 g/cc, and 43 Tex, respectively. The maximum tensile strength was obtained 53.55 MPa for GL 20 mm and Young’s modulus 572.21 MPa for GL 30 mm. The required energy at break was recorded during the tensile strength experiment from the tensile strength tester and the average values for GL 20 mm and GL 30 mm are 0.05381 J and 0.08968 J, respectively. The thermal analysis ensured the thermal sustainability of CTF fiber up to 230 °C. Entirely the aforementioned outcomes ensured that the new CTF fiber is the expected reinforcement to the fiber-reinforced composite materials.

scholarly journals Potensi Pemanfaatan Serat Selulosa sebagai Material Bahan Baku dalam Sintesis Filter Udara Non-Woven sesuai Standar TAPPI T 205

2020 ◽  
Vol 10 (2) ◽  
pp. 37-42
Author(s):  
Irwan Suriaman ◽  
Mardiyati ◽  
Jooned Hendrarsakti ◽  
Ari Darmawan Pasek
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Raw Materials ◽  
Natural Fibers ◽  
Morphological Characteristics ◽  
Sem Analysis ◽  
Raw Material ◽  
Ramie Fiber ◽  
Tropical Country ◽  
Materials Used

Industry 4.0 era materials used by entrepreneurs should be recycled, environmentally friendly, renewable with less chemical content. Indonesia as a tropical country has a large land area with the potential to produce the largest natural fiber in the world. One opportunity that can be applied to the utilization of natural fibers in air filters that currently use dominant materials is synthetic fibers. natural fiber has the advantage because it does not contain toxic chemicals, local raw materials, and is easily produced. This research will analyze the mechanical and morphological characteristics of biological fibers that have great potential as pre-filter raw material. Analysis of mechanical properties through tensile strength testing for single fibers and morphological analysis through scanning electron microscopy (SEM). Tensile testing was the results are; palm oil has a tensile strength of 620 MPa; 998 MPa and 213 MPa flax coconut fiber. For the morphological test results from SEM analysis for ramie fiber, it looks solid without fiber holes; The fibers appear to be many small fibers bound to one another while coir fibers have many pore holes in one observed fiber.

Preparation and Characterization of Physical Properties of Durian Skin Fibers Biocomposite

2012 ◽  
Vol 576 ◽  
pp. 212-215 ◽  
Author(s):  
R.M. Manshor ◽  
Hazleen Anuar ◽  
Wan Busu Wan Nazri ◽  
M.I. Ahmad Fitrie
Keyword(s):  
Natural Fiber ◽  
Natural Fibers ◽  
Crystallinity Index ◽  
Average Diameter ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lignocellulosic Fiber ◽  
The Common

Durian skin fibres (DSF) are cellulose-based fibres extracted from the durian peel. This paper present the physical behaviour, chemical structure and crystallinity of the fibres, as observed by environmental scanning electron microscope (ESEM), Fourier transform infrared (FTIR) and X-ray diffraction (XRD). The characteristic of the natural fibers produces from durian skins are similar with other types of natural fiber. The average diameter and density are 0.299 mm and 1.243 g/cm3, respectively while the crystallinity index is slightly higher than the common fibers. The properties and charecteristic of durian skin fibers are within the propertise of lignocellulosic fiber which is suitable for development of biocomposite materials.

Effect of Fiber Parameters on the Mechanical Properties of Banana-Glass Fiber Hybrid Composites

2014 ◽  
Vol 592-594 ◽  
pp. 202-205
Author(s):  
V. Santhanam ◽  
M. Chandrasekaran ◽  
N. Venkateshwaran
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Length ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Synthetic Fiber

Composite materials are widely used for their superior properties such as high strength to weight ratio, high tensile strength, low thermal expansion, low density etc. Due to environmental issues the eco-friendly composites are being explored. Natural fibers as reinforcement for polymer composites are widely studied. But natural fibers lack better mechanical properties when compared with synthetic fibers. Hence mixing the natural fiber with a synthetic fiber such as glass fiber will improve mechanical properties of the composites. In this study banana fiber is mixed with glass fiber, and the mixture is used as reinforcement in epoxy matrix. The composite specimens were prepared using hand layup technique, the fibers were randomly oriented. Further the fiber length was varied as 10, 15, 20 and 25mm and volume fraction as 10%, 15%, 20% and 25%. Experiments were conducted to find the effect of fiber length and volume fraction on tensile strength, flexural strength, water absorption properties of the composites. It is observed that a fiber length of 20mm and 20% fiber volume fraction gave better mechanical properties.

scholarly journals Characterization of natural cellulosic fiber isolated from Malaysian Cymbopogan citratus leaves

BioResources ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. 7729-7750
Author(s):  
Zatil Hafila Kamaruddin ◽  
Ridhwan Jumaidin ◽  
Ahmad Ilyas Rushdan ◽  
Mohd Zulkefli Selamat ◽  
Roziela Hanim Alamjuri
Keyword(s):  
Chemical Composition ◽  
Natural Fiber ◽  
Morphological Characteristics ◽  
Crystallinity Index ◽  
Composition Analysis ◽  
Green Composite ◽  
X Ray Diffraction ◽  
First Time ◽  
Cymbopogan Citratus

A novel natural fiber derived from the Cymbopogan citratus plant was investigated for the first time. The characterization of the C. citratus fibers was conducted, and the chemical composition and physical, thermal, mechanical, crystallinity, and morphological characteristics were studied. The chemical composition analysis of Cymbopogan citratus fiber revealed that the suggested fiber was rich in cellulose contents (37.6%). The tensile test of C. citratus fiber demonstrated the fiber’s average tensile strength of 43.81 ± 15.27 MPa and modulus of elasticity of 1.046 ± 0.33 GPa. Further analysis with X-ray diffraction (XRD) confirmed that the crystallinity index of Cymbopogan citratus fiber was 35.2%, and the crystalline size was estimated as 4.28 nm. The Cymbopogan citratus fiber’s thermal stability was investigated via thermogravimetric analysis (TGA) and observed to be thermally stable (230 °C). A morphological investigation was employed on the fiber via a scanning electron microscope (SEM). The morphological study result exhibited that the fiber had a perforated and rough surface with the lumen in the center. Thus, the findings revealed that the Cymbopogan citratus fiber was a promising potential reinforcement for thermoplastic green composite applications.

scholarly journals A Review on Bast Fiber Reinforced Thermosetting Matrix Composite

2019 ◽  
pp. 289-299
Author(s):  
Snehlata Pandey ◽  
Atul Kumar Tiwari
Keyword(s):  
Natural Fiber ◽  
Weight Ratio ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Bast Fiber ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite ◽  
Thermoset Epoxy ◽  
Reinforced Composite Material

The development of natural resources occurs due to biodegradability, ecofriendly and good strength to weight ratio in the engineering products. Natural fiber is obtained from various parts of the plant such as bast, leaf, seed, fruit, stalk, grass etc. In the present work take an overview of the characterization of the BF like failure mechanism, manufacturing process & overall properties. It deals with the potential energy absorbed by the natural fiber reinforced composite material. NFRC material replaced the various synthetic fiber. According to the literature survey the various work was carried out on the BF which shows its importance comparatively with the other fiber extract from the plant. BF is used as the reinforcement and thermoset epoxy used as matrix

scholarly journals Delamination and Manufacturing Defects in Natural Fiber-Reinforced Hybrid Composite: A Review

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1323
Author(s):  
M. J. Suriani ◽  
Hannah Zalifah Rapi ◽  
R. A. Ilyas ◽  
Michal Petrů ◽  
S. M. Sapuan
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composite ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Manufacturing Industries ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Manufacturing Defects ◽  
Reinforced Composite

In recent years, most boat fabrication companies use 100% synthetic fiber-reinforced composite materials, due to their high performance of mechanical properties. In the new trend of research on the fabrication of boat structure using natural fiber hybrid with kevlar/fiberglass-reinforced composite, the result of tensile, bending, and impact strength showed that glass fiber-reinforced polyester composite gave high strength with increasing glass fiber contents. At some point, realizing the cost of synthetic fiber is getting higher, researchers today have started to use natural fibers that are seen as a more cost-effective option. Natural fibers, however, have some disadvantages, such as high moisture absorption, due to repelling nature; low wettability; low thermal stability; and quality variation, which lead to the degradation of composite properties. In recent times, hybridization is recommended by most researchers as a solution to natural fiber’s weaknesses and to reduce the use of synthetic fibers that are not environmentally friendly. In addition, hybrid composite has its own special advantages, i.e., balanced strength and stiffness, reduced weight and cost, improved fatigue resistance and fracture toughness, and improved impact resistance. The synthetic–nature fiber hybrid composites are used in a variety of applications as a modern material that has attracted most manufacturing industries’ attention to shift to using the hybrid composite. Some of the previous studies stated that delamination and manufacturing had influenced the performance of the hybrid composites. In order to expand the use of natural fiber as a successful reinforcement in hybrid composite, the factor that affects the manufacturing defects needs to be investigated. In this review paper, a compilation of the reviews on the delamination and a few common manufacturing defect types illustrating the overview of the impact on the mechanical properties encountered by most of the composite manufacturing industries are presented.

New Coordination Compounds of Fe(III) with Organic Ligands

2009 ◽  
Vol 59 (12) ◽  
Author(s):  
Mihaela Flondor ◽  
Ioan Rosca ◽  
Doina Sibiescu ◽  
Mihaela-Aurelia Vizitiu ◽  
Daniel-Mircea Sutiman ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Complex Compounds ◽  
Organic Ligands ◽  
X Ray Diffraction ◽  
X Ray ◽  
Elemental Chemical Analysis ◽  
Structural Formulae ◽  
Paramagnetic Properties

In this paper the synthesis and the study of some complex compounds of Fe(III) with ligands derived from: 2-(4-chloro-phenylsulfanyl)-1-(2-hydroxy-3,5-diiodo-phenyl)-ethanone (HL1), 1-(3,5-dibromo-2-hydroxy-phenyl)-2-phenylsulfanyl-ethanone(HL2), and 2-(4-chloro-phenylsulfanyl)-1-(3,5-dibromo-2-hydroxy-phenyl)-ethanone (HL3) is presented. The characterization of these complexes is based on method as: the elemental chemical analysis, IR and ESR spectroscopy, M�ssbauer, the thermogravimetric analysis and X-ray diffraction. Study of the IR and chemical analysis has evidenced that the precipitates form are a complexes and the combination ratio of M:L is 1:2. The central atoms of Fe(III) presented paramagnetic properties and a octaedric hybridization. Starting from this precipitation reactions, a method for the gravimetric determination of Fe(III) with this organic ligands has been possible. Based on the experimental data on literature indications, the structural formulae of the complex compounds are assigned.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

scholarly journals Manufacture and Mechanical Behavior of Green Polymeric Composite Reinforced with Hydrated Cotton Fiber

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Ênio Henrique Pires da Silva ◽  
Emiliano Barretto Almendro ◽  
Amanda Albertin Xavier da Silva ◽  
Guilherme Waldow ◽  
Flaminio CP Sales ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cotton Fiber ◽  
Natural Fibers ◽  
Young Modulus ◽  
Polymeric Composite ◽  
Morphological Characterization ◽  
Comparison And Study ◽  
Fiber Fabric

Composites using natural fibers as reinforcement and biodegradable polymers as matrix are considered environmentally friendly materials. This paper seeks the mechanical and morphological characterization of a biocomposite of polyurethane (PU) derived from a blend of vegetable oils doped with aluminatrihydrate (ATH) and reinforced with hydrated cotton fiber fabric (HCF). The comparison and study were performed based on the properties of the: (i) pure PU; (ii) PU doped with ATH containing 30% of the final mass (PU+30%ATH); (iii) composite of PU reinforced with 7 layers of cotton fiber fabric (PU+7CF); (iv) composite of PU+30%ATH reinforced with 7 layers of CF (PU+30%ATH+7CF); (v) composite of PU+30%ATH reinforced with 7 layers of hydrated cotton fiber fabric (PU+30%ATH+7HCF). The mechanical properties obtained according to the tensile test for the composite PU+30%ATH+CF with fibers oriented at 0° showed a significant increment in tensile strength (60 MPa) and the modulus of elasticity (4.7 GPa) when compared to pure PU (40 MPa) and (1.7 GPa) respectively. PU+30%ATH also presented a rising tensile strength (31 MPa) and Young modulus (2.6 GPa). For the composite with addition of water, results presented a significant decrease in strength (31.3 MPa) and stiffness (0.9 GPa) than the composite with no water. Electron microscopy (SEM) analyses exhibited that the samples with addition of water showed the presence of large amounts of pores and the lower interaction between matrix and fiber. These results may explain the lower mechanical properties of this material. DOI: http://dx.doi.org/10.30609/JETI.2019-7576

scholarly journals Karakterisasi Mekanik Komposit Matriks Polipropilena High Impact Dengan Serat Alam Acak Dengan Metode Hand Lay Up Untuk Komponen Automotive

2020 ◽  
Vol 3 (3) ◽  
Author(s):  
Alfan Ekajati Latief ◽  
Nuha Desi Anggraeni ◽  
Dedy Hernady
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Mesh Size ◽  
High Impact ◽  
Hemp Fiber ◽  
Polypropylene Matrix ◽  
The Impact ◽  
Pineapple Leaves

ABSTRAK Serat alam yang berfungsi sebagai penguat memiliki sifat yang lebih ringan, mudah dibentuk, tahan korosi, harga murah dan memiliki kekuatan yang sama dengan material logam. Serat bahan alami yang memiliki kekuatan tarik, tekan dan impak yang baik diantaranya serat rami dan daun nanas. Untuk matriks Polipropilena high impact (PPHI) yang banyak digunakan dalam industri otomotif.. Pada penelitian ini dipelajari pengaruh fraksi volume serat alami terhadap sifat mekanik komposit PPHI berpenguat serat alami. Komposit PPHI dibuat dengan menggunakan metode Hand Lay Up pada temperatur 2500C dengan fraksi volume serat alami sebesar 10%, dimana serat dibuat digunting halus hingga memiliki ukuran mesh 120/170, 170/200 dan dibawah 200 mesh, Kekuatan tarik komposit diukur dengan mengacu pada standar ASTM 3039, kekuatan tekan diukur mengacu pada ASTM D 695. Harga Impak dari komposit diukur dengan mengacu pada ASTM D 6110-04. Pada penelitian ini dapat disimpulkan, fraksi volume 10 % serat alami yang baik ketika dicampur dengan matriks polipropilena high impact adalah serat nanas dengan meshing 170/200 dapat meningkatkan kekuatan tarik PPHI sebesar 40 % dan meningkatkan harga impak PPHI sebesar 50,8 % jika dilihat penelitan sebelumnya yakni menggunakan serat rami dibawah mesh 1200 dengan matriks PPHI. Kata Kunci: Rami, Daun Nanas, Polipropilena High Impact, Hand Lay Up. ABSTRACT Natural fibers that function as reinforcement have lighter properties, are easily formed, are corrosion resistant, are cheap and have the same strength as metal materials. Natural fiber which has good tensile, compressive and impact strength including Ramie and pineapple leaves. For high impact polypropylene matrix (PPHI) which is widely used in the automotive industry. In this study the effect of volume fraction of natural fibers on the mechanical properties of PPHI composites with natural fiber reinforced properties was studied. PPHI composites are made using the Hand Lay Up method at a temperature of 2500C with a volume fraction of natural fibers of 10%, where fibers are made finely shaved to have a mesh size of 120/170, 170/200 and below 200 mesh, the tensile strength of the composite is measured by reference to the standard ASTM 3039, compressive strength measured refers to ASTM D 695. The impact price of the composite is measured with reference to ASTM D 6110-04. In this study it can be concluded, a good volume fraction of 10% natural fiber when mixed with high impact polypropylene matrix is pineapple fiber with meshing 170/200 can increase the tensile strength of PPHI by 40% and increase the impact price of PPHI by 50.8% if seen by research previously that used hemp fiber under mesh 1200 with PPHI matrix. Keywords: Ramie Pineapple, High Impact Polypropylene, Hand Lay Up.

Sign in / Sign up

Export Citation Format

Share Document