scholarly journals Synchronized resistive-pulse analysis with flow visualization for single micro- and nanoscale objects driven by optical vortex in double orifice

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Kichitaro Nakajima ◽  
Ryoji Nakatsuka ◽  
Tetsuro Tsuji ◽  
Kentaro Doi ◽  
Satoyuki Kawano
Keyword(s):  
Flow Visualization ◽  
High Speed ◽  
Signal To Noise Ratio ◽  
Ionic Current ◽  
Optical Vortex ◽  
Object Identification ◽  
Resistive Pulse ◽  
Short Period ◽  
Pulse Analysis ◽  
Double Orifice

AbstractResistive-pulse analysis is a powerful tool for identifying micro- and nanoscale objects. For low-concentration specimens, the pulse responses are rare, and it is difficult to obtain a sufficient number of electrical waveforms to clearly characterize the targets and reduce noise. In this study, we conducted a periodic resistive-pulse analysis using an optical vortex and a double orifice, which repetitively senses a single micro- or nanoscale target particle with a diameter ranging from 700 nm to 2 $$\mu$$ μ m. The periodic motion results in the accumulation of a sufficient number of waveforms within a short period. Acquired pulses show periodic ionic-current drops associated with the translocation events through each orifice. Furthermore, a transparent fluidic device allows us to synchronously average the waveforms by the microscopic observation of the translocation events and improve the signal-to-noise ratio. By this method, we succeed in distinguishing single particle diameters. Additionally, the results of measured signals and the simultaneous high-speed observations are used to quantitatively and systematically discuss the effect of the complex fluid flow in the orifices on the amplitude of the resistive pulse. The synchronized resistive-pulse analysis by the optical vortex with the flow visualization improves the pulse-acquisition rate for a single specific particle and accuracy of the analysis, refining the micro- and nanoscale object identification.

Predicting, Improving and Visualizing Cavitation Characteristics of First-Stage Impellers in High-Speed, High-Energy Pumps

2015 ◽  
Author(s):  
Nico van den Berg ◽  
Tim Bastiaansen ◽  
Kariem Elebiary
Keyword(s):  
Flow Visualization ◽  
High Speed ◽  
Leading Edge ◽  
High Energy ◽  
Full Scale ◽  
Centrifugal Pumps ◽  
Numerical Predictions ◽  
Test Loop ◽  
Short Period ◽  
Observed Damage

This paper describes the development and verification of a new first-stage impeller using an automated and parameterized process of reshaping the vane leading edge. By utilizing Computational Fluid Dynamics (CFD), several design iterations can be performed in a short period of time driven by the numerical NPSHi curve — which is an indication of the NPSH at which the first cavitation bubbles will start to form [1]. Based on the original (parent) impeller hydraulic, five designs were created with a variety of vane leading edge shapes. To ensure the Best Cavitation Point (BCP) is located near rated condition and the NPSH3 requirement is met at maximum operating flow, the most promising design was selected and manufactured at full scale using rapid prototyping. During full scale, reduced speed, flow visualization testing in a dedicated test loop of a reworked and a non-reworked original impeller and the new impeller design, it was confirmed that the results were in line with the numerical predictions; the field impeller showed cavitation formation that matched the observed damage pattern and the new impeller design demonstrated a significant decrease in cavity lengths. For the condition of field NPSHA at 80 and 100 percent rated flow, cavitation formation was not observed anymore for the new design. The lesson learned from this study is that the NPSH3 requirement alone is an inappropriate criterion for high-speed, high-energy centrifugal pumps. It is advised to map the development of cavitation for all high-energy pumps having high eye peripheral speeds. Besides this, it can be concluded that CFD is a viable tool in assessing incipient cavitation behavior and can be considered an alternative to flow visualization testing.

40 Gb/s High-speed mode-division multiplexing transmission employing NRZ modulation format

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Rabiu Imam Sabitu ◽  
Nafizah Goriman Khan ◽  
Amin Malekmohammadi
Keyword(s):  
System Performance ◽  
High Speed ◽  
Direct Detection ◽  
Signal To Noise Ratio ◽  
Optical Signal ◽  
Threshold Power ◽  
Modulation Format ◽  
Transmission Distance ◽  
Mode Division Multiplexing ◽  
Speed Mode

AbstractThis report examines the performance of a high-speed MDM transmission system supporting four nondegenerate spatial modes at 10 Gb/s. The analysis adopts the NRZ modulation format to evaluate the system performance in terms of a minimum power required (PN) and the nonlinear threshold power (PTH) at a BER of 10−9. The receiver sensitivity, optical signal-to-noise ratio, and the maximum transmission distance were investigated using the direct detection by employing a multimode erbium-doped amplifier (MM-EDFA). It was found that by properly optimizing the MM-EDFA, the system performance can significantly be improved.

scholarly journals Internal face finishing for a cooling channel using a fluid containing free abrasive grains

2021 ◽  
Author(s):  
Mitsugu Yamaguchi ◽  
Tatsuaki Furumoto ◽  
Shuuji Inagaki ◽  
Masao Tsuji ◽  
Yoshiki Ochiai ◽  
...  
Keyword(s):  
High Speed ◽  
Flow Behavior ◽  
Flow Simulation ◽  
Cooling Channel ◽  
H13 Steel ◽  
Channel Diameter ◽  
Abrasive Grains ◽  
Low Viscosity ◽  
Short Period ◽  
Internal Pressures

AbstractIn die-casting and injection molding, a conformal cooling channel is applied inside the dies and molds to reduce the cycle time. When the internal face of the channel is rough, both cooling performance and tool life are negatively affected. Many methods for finishing the internal face of such channels have been proposed. However, the effects of the channel diameter on the flow of a low-viscosity finishing media and its finishing characteristics for H13 steel have not yet been reported in the literature. This study addresses these deficiencies through the following: the fluid flow in a channel was computationally simulated; the flow behavior of abrasive grains was observed using a high-speed camera; and the internal face of the channel was finished using the flow of a fluid containing abrasive grains. The flow velocity of the fluid with the abrasive grains increases as the channel diameter decreases, and the velocity gradient is low throughout the channel. This enables reduction in the surface roughness for a short period and ensures uniform finishing in the central region of the channel; however, over polishing occurs owing to the centrifugal force generated in the entrance region, which causes the form accuracy of the channel to partially deteriorate. The outcomes of this study demonstrate that the observational finding for the finishing process is consistent with the flow simulation results. The flow simulation can be instrumental in designing channel diameters and internal pressures to ensure efficient and uniform finishing for such channels.

scholarly journals High-speed high-resolution laser diode-based photoacoustic microscopy for in vivo microvasculature imaging

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Xiufeng Li ◽  
Victor T C Tsang ◽  
Lei Kang ◽  
Yan Zhang ◽  
Terence T W Wong
Keyword(s):  
High Resolution ◽  
High Speed ◽  
High Performance ◽  
Continuous Wave ◽  
Signal To Noise Ratio ◽  
Cost Effective ◽  
High Signal ◽  
Photoacoustic Microscopy ◽  
Mouse Ear

AbstractLaser diodes (LDs) have been considered as cost-effective and compact excitation sources to overcome the requirement of costly and bulky pulsed laser sources that are commonly used in photoacoustic microscopy (PAM). However, the spatial resolution and/or imaging speed of previously reported LD-based PAM systems have not been optimized simultaneously. In this paper, we developed a high-speed and high-resolution LD-based PAM system using a continuous wave LD, operating at a pulsed mode, with a repetition rate of 30 kHz, as an excitation source. A hybrid scanning mechanism that synchronizes a one-dimensional galvanometer mirror and a two-dimensional motorized stage is applied to achieve a fast imaging capability without signal averaging due to the high signal-to-noise ratio. By optimizing the optical system, a high lateral resolution of 4.8 μm has been achieved. In vivo microvasculature imaging of a mouse ear has been demonstrated to show the high performance of our LD-based PAM system.

scholarly journals A High-Speed, Light-Weight Scalar Magnetometer Bird for km Scale UAV Magnetic Surveying: On Sensor Choice, Bird Design, and Quality of Output Data

2021 ◽  
Vol 13 (4) ◽  
pp. 649
Author(s):  
Arne Døssing ◽  
Eduardo Lima Simoes da Silva ◽  
Guillaume Martelet ◽  
Thorkild Maack Rasmussen ◽  
Eric Gloaguen ◽  
...  
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Signal To Noise Ratio ◽  
Regional Scale ◽  
Weather Conditions ◽  
Light Weight ◽  
Output Data ◽  
Efficient Manner ◽  
Flexible System ◽  
Scalar Data

Magnetic surveying is a widely used and cost-efficient remote sensing method for the detection of subsurface structures at all scales. Traditionally, magnetic surveying has been conducted as ground or airborne surveys, which are cheap and provide large-scale consistent data coverage, respectively. However, ground surveys are often incomplete and slow, whereas airborne surveys suffer from being inflexible, expensive and characterized by a reduced signal-to-noise ratio, due to increased sensor-to-source distance. With the rise of reliable and affordable survey-grade Unmanned Aerial Vehicles (UAVs), and the developments of light-weight magnetometers, the shortcomings of traditional magnetic surveying systems may be bypassed by a carefully designed UAV-borne magnetometer system. Here, we present a study on the development and testing of a light-weight scalar field UAV-integrated magnetometer bird system (the CMAGTRES-S100). The idea behind the CMAGTRES-S100 is the need for a high-speed and flexible system that is easily transported in the field without a car, deployable in most terrain and weather conditions, and provides high-quality scalar data in an operationally efficient manner and at ranges comparable to sub-regional scale helicopter-borne magnetic surveys. We discuss various steps in the development, including (i) choice of sensor based on sensor specifications and sensor stability tests, (ii) design considerations of the bird, (iii) operational efficiency and flexibility and (iv) output data quality. The current CMAGTRES-S100 system weighs ∼5.9 kg (including the UAV) and has an optimal surveying speed of 50 km/h. The system was tested along a complex coastal setting in Brittany, France, targeting mafic dykes and fault contacts with magnetite infill and magnetite nuggets (skarns). A 2.0 × 0.3 km area was mapped with a 10 m line-spacing by four sub-surveys (due to regulatory restrictions). The sub-surveys were completed in 3.5 h, including >2 h for remobilisation and the safety clearance of the area. A noise-level of ±0.02 nT was obtained and several of the key geological structures were mapped by the system.

scholarly journals Error Performance Estimation of Modulated Retroreflective Transdermal Optical Wireless Links with Diversity under Generalized Pointing Errors

Telecom ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 167-180
Author(s):  
George K. Varotsos ◽  
Hector E. Nistazakis ◽  
Konstantinos Aidinis ◽  
Fadi Jaber ◽  
Mohd Nasor ◽  
...  
Keyword(s):  
High Speed ◽  
Signal To Noise Ratio ◽  
Spatial Diversity ◽  
Performance Estimation ◽  
Optical Wireless ◽  
Wireless Data ◽  
Error Performance ◽  
Pointing Errors ◽  
Implanted Medical Devices ◽  
Recent Developments

Recent developments in both optical wireless communication (OWC) systems and implanted medical devices (IMDs) have introduced transdermal optical wireless (TOW) technology as a viable candidate for extremely high-speed in-body to out-of-body wireless data transmissions, which are growing in demand for many vital biomedical applications, including telemetry with medical implants, health monitoring, neural recording and prostheses. Nevertheless, this emerging communication modality is primarily hindered by skin-induced attenuation of the propagating signal bit carrier along with its stochastic misalignment-induced fading. Thus, by considering a typical modulated retroreflective (MRR) TOW system with spatial diversity and optimal combining (OC) for signal reception in this work, we focus, for the first time in the MRR TOW literature, on the stochastic nature of generalized pointing errors with non-zero boresight (NZB). Specifically, under these circumstances, novel analytical mathematical expressions were derived for the total average bit error rate (BER) of various system configurations. Their results revealed significant outage performance enhancements when spatial diversity was utilized. Moreover, taking into consideration the total transdermal pathloss along with the effects of stochastic NZB pointing errors, the critical average signal-to-noise ratio (SNR) metric was evaluated for typical power spectral-density values.

Effects of Parameters on the Two-Phase Flow Instability in a Microchannel

2018 ◽  
Author(s):  
Yefei Liu ◽  
Yang Liu ◽  
Xingtuan Yang ◽  
Liqiang Pan
Keyword(s):  
Heat Flux ◽  
High Speed ◽  
Flow Instability ◽  
Working Fluid ◽  
Two Phase ◽  
Short Period ◽  
Period Oscillation ◽  
Data Acquisition Card ◽  
Series Of Experiments ◽  
Vertical Microchannel

Series of experiments are conducted in a single microchannel, where subcooled water flows upward inside a transparent and vertical microchannel. The cross section of the channel is rectangle with the hydraulic diameter of 2.8mm and the aspect ratio of 20. The working fluid is 3–15K subcooled and surface heat flux on the channel is between 0–3.64 kW/m2, among which two-phase instability at low vapor quantity may occur. By using a novel transparent heating technique and a high-speed camera, visualization results are obtained. The parameters are acquired with a National Instruments Data Acquisition card. In the experiments, long-period oscillation and short-period oscillation are observed as the primary types of instability in a microchannel. Instability characteristics represented from signals correspond well with the flow pattern. Moreover, effects of several parameters are investigated. The results indicate that the oscillating period generally increases with the heat flux density and decreases with inlet subcooling, while the effects of inlet resistance are more complex.

System Design and Modeling of a Thermally Activated Reconfigurable Wing

2010 ◽  
Author(s):  
Richard Beblo ◽  
Darrel Robertson ◽  
James Joo ◽  
Brian Smyers ◽  
Gregory Reich
Keyword(s):  
Thermal Energy ◽  
High Speed ◽  
Frictional Heating ◽  
Mechanical Analysis ◽  
Design Tool ◽  
System Level ◽  
Morphing Aircraft ◽  
Thermal Actuation ◽  
Short Period ◽  
Reconfigurable Structures

Reconfigurable structures such as morphing aircraft generally require an on board energy source to function. Frictional heating during the high speed deployment of a blunt nosed low speed reconnaissance air vehicle can provide a large amount of thermal energy during a short period of time. This thermal energy can be collected, transferred, and utilized to reconfigure the deployable aircraft. Direct utilization of thermal energy has the ability to significantly decrease or eliminate the losses associated with converting thermal energy to other forms, such as electric. The following work attempts to describe possible system designs and components that can be utilized to transfer the thermal energy harvested at the nose of the aircraft during deployment to internal components for direct thermal actuation of a reconfigurable wing structure. A model of a loop heat pipe is presented and used to predict the time dependant transfer of energy. Previously reported thermal profiles of the nose of the aircraft calculated based on trajectory and mechanical analysis of the actuation mechanism are reviewed and combined with the model of the thermal transport system providing a system level feasibility investigation and design tool. The efficiency, implementation, benefits, and limitations of the direct use thermal system are discussed and compared with currently utilized systems.

Sign in / Sign up

Export Citation Format

Share Document