scholarly journals Optimization Sugarcane and Paddy Waste as Bio-Composite Material to Absorb Impact Force

2021 ◽  
Vol 328 ◽  
pp. 07001
Author(s):  
Anis Arendra ◽  
Rifky Yusron ◽  
Teguh Prasetyo
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Sugarcane Bagasse ◽  
Significant Influence ◽  
Polyester Resin ◽  
Environmental Problem ◽  
Impact Force ◽  
Agricultural Waste ◽  
Fibre Direction ◽  
Absorb Impact Energy

Agricultural waste such as sugarcane and paddy are common during harvesting to production process. Sometimes they burned after the harvest process, as consequently the environmental problem got multiply. Demand for Composite Material got inflate recently, because they are lighter and stronger than Polyethylene Plastic. Filler in composite materials is expensive and requires precise design. The aim of this research is to create cheap and eco-friendly composite materials, besides raised value of agricultural waste. The composite material using sugarcane bagasse as fibre, paddy chaff powder applied as filler and polyester resin as matrix. In this study, we varied the fibre direction with composition of sugarcane bagasse and paddy chaff powder. In this research fibre direction has three levels they are 0, 45 and 90 degrees. Composition between sugarcane bagasse, paddy chaff powder and polyester resin ratio has three levels they are 15:15:70, 12.5:12.5:75 and 10:10:80. ANOVA test shown fibre direction has significant influence to ability of the material to absorb impact energy 78.14 percent than fibre composition 12.10 percent. The highest impact absorb value is 0.3 degrees Joule on composition ratio paddy chaff: sugarcane: polyester resin is 15:15:70 and 45 degrees fibre direction.

Influence of the Dimensions of the Mesh of the Fiber Grid Reinforcement of Composite Materials

2013 ◽  
Vol 550 ◽  
pp. 9-16
Author(s):  
Kamal Ait Tahar ◽  
R. Bahar
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Composite Materials ◽  
Experimental Analysis ◽  
Weibull Modulus ◽  
Polyester Resin ◽  
Dynamic Test ◽  
Technical Aspect ◽  
Metal Fiber ◽  
Grid Reinforcement

Currently, the composite materials make important great strides, considering their high mechanical properties. The studies relating to the conceptual, technical aspect and modeling of their mechanical behavior are more than desirable. The mechanical properties of the composite material depend on several factors as the nature of fibers, the fiber/matrix ratio, compatibility, homogeneity... In this study, we present the results of an experimental analysis of the behavior of the composite material, under a static and a dynamic loading. The composite material is composed respectively of the glass and metal fiber reinforcement. A various dimensions of the mesh are considering. The resin used is polyester Resow 55 E. The dynamic test ( Knoop test) is carried out on various specimens made up of an polyester resin RESOW 55 E reinforced with varied powder nature. It makes it possible to measure the hardness of composite materials. The analysis of the results shows clearly that the mechanical properties are strongly influenced by the dimensions of the elementary mesh of the fiber grid reinforcement. Based on experimental results, a Weibull modulus has been established for each specimen.

Study of the Composite Materials Optimal Structure Containing a Hollow Aluminum and Silica Microsphere Dependence on Humidity

2020 ◽  
Vol 12 ◽  
Author(s):  
Alexandra Atyaksheva ◽  
Yermek Sarsikeyev ◽  
Anastasia Atyaksheva ◽  
Olga Galtseva ◽  
Alexander Rogachev
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Strength Function ◽  
Theory And Practice ◽  
Optimal Structure ◽  
Optimal Size ◽  
Structure And Properties ◽  
Power Functions ◽  
Silica Microsphere ◽  
Heat Engineering

Aims:: The main goals of this research are exploration of energy-efficient building materials when replacing natural materials with industrial waste and development of the theory and practice of obtaining light and ultra-light gravel materials based on mineral binders and waste dump ash and slag mixtures of hydraulic removal. Background.: Experimental data on the conditions of formation of gravel materials containing hollow aluminum and silica microsphere with opportunity of receipt of optimum structure and properties depending on humidity with the using of various binders are presented in this article. This article dwells on the scientific study of opportunity physical-mechanical properties of composite materials optimization are considered. Objective.: Composite material contains hollow aluminum and silica microsphere. Method.: The study is based on the application of the method of separation of power and heat engineering functions. The method is based on the use of the factor structure optimality, which takes into account the primary and secondary stress fields of the structural gravel material. This indicates the possibility of obtaining gravel material with the most uniform distribution of nano - and microparticles in the gravel material and the formation of stable matrices with minimization of stress concentrations. Experiments show that the thickness of the cement shell, which performs power functions, is directly related to the size of the raw granules. At the same time, the thickness of the cement crust, regardless of the type of binder, with increasing moisture content has a higher rate of formation for granules of larger diameter. Results.: The conditions for the formation of gravel composite materials containing a hollow aluminosilicate microsphere are studied. The optimal structure and properties of the gravel composite material were obtained. The dependence of the strength function on humidity and the type of binder has been investigated. The optimal size and shape of binary form of gravel material containing a hollow aluminosilicate microsphere with a minimum thickness of a cement shell and a maximum strength function was obtained. Conclusion.: Received structure allows to separate power and heat engineering functions in material and to minimize the content of the excited environment centers.

Hierarchical ZSM-22/PHTS composite material and its hydro-isomerization performance in hydro-upgrading of gasoline

2021 ◽  
Author(s):  
Jiyuan Fan ◽  
Chengkun Xiao ◽  
Jinlin Mei ◽  
Cong Liu ◽  
Aijun Duan ◽  
...  
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Impregnation Method ◽  
Molar Ratios

CoMo series catalysts based on ZSM-22/PHTS (ZP) composite materials with different SiO2/Al2O3 molar ratios were prepared via the impregnation method. The properties of the ZP material and the corresponding catalysts...

scholarly journals Acoustic Emission and K-S Metric Entropy as Methods for Determining Mechanical Properties of Composite Materials

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 145
Author(s):  
Lesław Kyzioł ◽  
Katarzyna Panasiuk ◽  
Grzegorz Hajdukiewicz ◽  
Krzysztof Dudzik
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Composite Material ◽  
Composite Materials ◽  
Testing Machine ◽  
Measurement Data ◽  
Entropy Method ◽  
Displacement Sensor ◽  
Metric Entropy ◽  
Plastic Phase

Due to the unique properties of polymer composites, these materials are used in many industries, including shipbuilding (hulls of boats, yachts, motorboats, cutters, ship and cooling doors, pontoons and floats, torpedo tubes and missiles, protective shields, antenna masts, radar shields, and antennas, etc.). Modern measurement methods and tools allow to determine the properties of the composite material, already during its design. The article presents the use of the method of acoustic emission and Kolmogorov-Sinai (K-S) metric entropy to determine the mechanical properties of composites. The tested materials were polyester-glass laminate without additives and with a 10% content of polyester-glass waste. The changes taking place in the composite material during loading were visualized using a piezoelectric sensor used in the acoustic emission method. Thanks to the analysis of the RMS parameter (root mean square of the acoustic emission signal), it is possible to determine the range of stresses at which significant changes occur in the material in terms of its use as a construction material. In the K-S entropy method, an important measuring tool is the extensometer, namely the displacement sensor built into it. The results obtained during the static tensile test with the use of an extensometer allow them to be used to calculate the K-S metric entropy. Many materials, including composite materials, do not have a yield point. In principle, there are no methods for determining the transition of a material from elastic to plastic phase. The authors showed that, with the use of a modern testing machine and very high-quality instrumentation to record measurement data using the Kolmogorov-Sinai (K-S) metric entropy method and the acoustic emission (AE) method, it is possible to determine the material transition from elastic to plastic phase. Determining the yield strength of composite materials is extremely important information when designing a structure.

scholarly journals Development of Detailed FE Numerical Models for Assessing the Replacement of Metal with Composite Materials Applied to an Executive Aircraft Wing

Aerospace ◽  
2021 ◽  
Vol 8 (7) ◽  
pp. 178
Author(s):  
Valerio Acanfora ◽  
Roberto Petillo ◽  
Salvatore Incognito ◽  
Gerardo Mario Mirra ◽  
Aniello Riccio
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Numerical Model ◽  
Numerical Models ◽  
Structural Performance ◽  
Aircraft Wing ◽  
Resin Infusion ◽  
Effectiveness Analysis ◽  
Liquid Resin Infusion ◽  
Process Constraints

This work provides a feasibility and effectiveness analysis, through numerical investigation, of metal replacement of primary components with composite material for an executive aircraft wing. In particular, benefits and disadvantages of replacing metal, usually adopted to manufacture this structural component, with composite material are explored. To accomplish this task, a detailed FEM numerical model of the composite aircraft wing was deployed by taking into account process constraints related to Liquid Resin Infusion, which was selected as the preferred manufacturing technique to fabricate the wing. We obtained a geometric and material layup definition for the CFRP components of the wing, which demonstrated that the replacement of the metal elements with composite materials did not affect the structural performance and can guarantee a substantial advantage for the structure in terms of weight reduction when compared to the equivalent metallic configuration, even for existing executive wing configurations.

Study on Mechanical Properties of the Composite Materials Film by Speckle Projection Method

2012 ◽  
Vol 496 ◽  
pp. 281-284
Author(s):  
Wen Wen Liu ◽  
Zhi Wang ◽  
Yun Hai Du ◽  
Xian Zhong Xu ◽  
Da Quan Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Composite Materials ◽  
Projection Method ◽  
Dynamic Deformation ◽  
Calibration Method ◽  
Deformation Measurement ◽  
Lens Distortion

An improved accurate speckle projection method is used for study the mechanical properties of the composite material film in the paper. A system for deformation measurement is developed with the telecentric lenses, in which such conventional lens’ disadvantages such as lens distortion and perspective error will be diminished. Experiments are performed to validate the availability and reliability of the calibration method. The system can also be used to measure the dynamic deformation and then results are also given.

scholarly journals High Mechanic Enhancement of Chopped Carbon Fiber Reinforced-Low-Density Unsaturated Polyester Resin Composite at Low Preparation Temperature with Facile Polymerization

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4273
Author(s):  
Jian Zhang ◽  
Xiaojun Wang ◽  
Xinjun Fu
Keyword(s):  
Composite Materials ◽  
Carbon Fiber ◽  
Low Temperature ◽  
Surface Defect ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Unsaturated Polyester Resin ◽  
Low Density ◽  
Fiber Reinforced ◽  
Preparation Temperature

Chopped carbon fiber-reinforced low-density unsaturated polyester resin (CCFR-LDUPR) composite materials with light weight and high mechanical properties were prepared at low temperature and under the synergistic action of methyl ethyl ketone peroxide (MEKP-II) and cobalt naphthenate. Optimal preparation conditions were obtained through an orthogonal experiment, which were preparation temperature at 58.0 °C, 2.00 parts per hundred of resin (phr) of NH4HCO3, 4.00 phr of chopped carbon fibers (CCFs) in a length of 6.0 mm, 1.25 phr of initiator and 0.08 phr of cobalt naphthenate. CCFR-LDUPR composite sample presented its optimal properties for which the density (ρ) was 0.58 ± 0.02 g·cm−3 and the specific compressive strength (Ps) was 53.56 ± 0.83 MPa·g−1·cm3, which is 38.9% higher than that of chopped glass fiber-reinforced low-density unsaturated polyester resin (CGFR-LDUPR) composite materials. Synergistic effects of initiator and accelerator accelerated the specific polymerization of resin in facile preparation at low temperature. Unique “dimples”, “plate microstructure” and “surface defect” fabricated the specific microstructure of the matrix of CCFR-LDUPR composite samples, which was different from that of cured unsaturated polyester resin (UPR) with “body defect” or that of CGFR-LDUPR with coexistence of “surface defect” and “body defect”.

Stress Field of Semi-Infinite Interface Crack Tip of Double Dissimilar Orthotropic Composite Materials

2010 ◽  
Vol 97-101 ◽  
pp. 1223-1226
Author(s):  
Jun Lin Li ◽  
Shao Qin Zhang
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Interface Crack ◽  
Interfacial Crack ◽  
Crack Tip ◽  
Stress Fields ◽  
Displacement Fields ◽  
Orthotropic Composite ◽  
Stress Functions ◽  
Secular Equations

The problem of orthotropic composite materials semi-infinite interfacial crack was studied, by constructing new stress functions and employing the method of composite material complex. In the case that the secular equations’ discriminates the and theoretical solutions to the stress fields and the displacement fields near semi-infinite interface crack tip without oscillation and inter-embedding between the interfaces of the crack are obtained, a comparison with finite element example was done to verify the correction of theoretical solution.

The Estimation of Thermal Conductivity for Alumina-Epoxy Composite Material with High Filling Volume Fraction

2014 ◽  
Vol 918 ◽  
pp. 21-26
Author(s):  
Chen Kang Huang ◽  
Yun Ching Leong
Keyword(s):  
Thermal Conductivity ◽  
Composite Material ◽  
Composite Materials ◽  
Physical Model ◽  
Electron Scattering ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
The Matrix ◽  
Transport Theorem ◽  
Good Agreement

In this study, the transport theorem of phonons and electrons is utilized to create a model to predict the thermal conductivity of composite materials. By observing or assuming the dopant displacement in the matrix, a physical model between dopant and matrix can be built, and the composite material can be divided into several regions. In each region, the phonon or electron scattering caused by boundaries, impurities, or U-processes was taken into account to calculate the thermal conductivity. The model is then used to predict the composite thermal conductivity for several composite materials. It shows a pretty good agreement with previous studies in literatures. Based on the model, some discussions about dopant size and volume fraction are also made.

scholarly journals A Review on a Straight Bevel Gear Made from Composite

2016 ◽  
Vol 5 (3) ◽  
pp. 73 ◽  
Author(s):  
Haidar F. AL-Qrimli ◽  
Karam S. Khalid ◽  
Ahmed M. Abdelrhman ◽  
Roaad K. Mohammed A ◽  
Husam M. Hadi
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Power Transmission ◽  
Bevel Gear ◽  
Robotic Arm ◽  
Straight Bevel Gear ◽  
Different Types ◽  
New Type ◽  
New Form ◽  
Material Composite

The purpose of this work is to present a clear fundamental thought for designing and investigating straight bevel gear made of composite material. Composite materials have the advantage of being light, producing low noises, and extra loading capacities. Due to these properties, it is highly preferable over conventional materials. A comparison between different types of material used in a gear structure will be shown. The outcome shows that a new form of cheap material may be useful for designing a new type of lighter and stiffer gear, designed for robotic arm applications or any power transmission application.

Sign in / Sign up

Export Citation Format

Share Document