scholarly journals Thermal management of machine compartment in a built-in refrigerator

2018 ◽  
Vol 240 ◽  
pp. 05005
Author(s):  
Milind Devle ◽  
Ankur Garg ◽  
Darci Cavali
Keyword(s):  
Heat Exchange ◽  
Cfd Simulation ◽  
Heat Extraction ◽  
Free Standing ◽  
Cfd Simulations ◽  
Performance Effectiveness ◽  
Hot Air ◽  
Computational Fluid Dynamics Cfd ◽  
Major Factors ◽  
Side Gap

In general a multi-door refrigerator machine compartment comprises of fan, condenser, compressor, control box, drain tray, and drain tubes. The performance of machine compartment depends upon the efficiency of heat extraction or heat exchange from heat generating components such as condenser and compressor. The efficiency of heat exchange can be improved by addressing two major factors, namely (1) Air bypass and (2) Hot air recirculation. The hot air recirculation in the machine compartment for builtin multi-door refrigerator configuration is the focus of this study. The results from Computational Fluid Dynamics (CFD) simulations show that efficiency of heat exchange for built-in application is lower than that for free-standing configuration. Recirculation of hot air and reduction in airflow are the two major factors which contribute towards the variation in machine compartment performance. The CFD simulations were coupled with Partial Factorial Design of Experiment (DoE) approach to systematically investigate the effect of variables such as (a) side gap and top gap between kitchen cabinetry and the refrigerator, (b) the baffle/flap (i.e. back and bottom of machine compartment) on the performance effectiveness of machine compartment. The results of the simulation provided critical design improvement directions resulting in performance improvement. Furthermore, the CFD simulation results were also compared to test data and the results compared favourably.

CFD simulation of empty fuel tanks separation from a trainer jet

2020 ◽  
Vol 92 (10) ◽  
pp. 1459-1468
Author(s):  
Aleksander Olejnik ◽  
Adam Dziubiński ◽  
Łukasz Kiszkowiak
Keyword(s):  
Cfd Simulation ◽  
Body Movement ◽  
Cfd Simulations ◽  
Content Type ◽  
Sequential Release ◽  
Wind Tunnel Data ◽  
Computational Fluid Dynamics Cfd ◽  
External Forces ◽  
Additional Value ◽  
Control Surfaces

Purpose This study aims to create 6-degree of freedom (SDOF) for computational fluid dynamics (CFD) simulations of body movement, and to validate using the experimental data for empty tank separation from I-22 Iryda jet trainer. The procedure has an ability to be modified or extended, to simulate, for example, a sequential release from the joints. Design/methodology/approach A set of CFD simulations are calculated. Both the SDOF procedure and the CFD simulation settings are validated using the wind tunnel data available for the aircraft. Findings The simulation using designed procedure gives predictable results, but offers availability to be modified to represent external forces, i.e. from body interaction or control system without necessity to model the control surfaces. Practical implications The procedure could be used to model the separation of external stores and design the deployment of anti-radar chaff, flares or ejection seats. Originality/value The work presents original work, caused by insufficient abilities of original SDOF procedure in ANSYS code. Additional value is the ability of the procedure to be easily modified.

Transient CFD Visualization of Fossil Fuel Combustion Simulations

2003 ◽  
Author(s):  
Brian Dotson ◽  
Kent Eshenberg ◽  
Chris Guenther ◽  
Thomas O’Brien
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Cfd Simulation ◽  
Low Cost ◽  
Three Dimensional ◽  
Cfd Simulations ◽  
Projection System ◽  
Computational Fluid Dynamics Cfd ◽  
High Level ◽  
Wall System

The design of high-efficiency lower-emission coal-fed power plants is facilitated by the extensive use of computational fluid dynamics (CFD) simulations. This paper describes work conducted at the National Energy Technology Laboratory (NETL) and Pittsburgh Supercomputing Center (PSC) to provide an environment for the immersive three-dimensional visualization of CFD simulation results. A low-cost high-resolution projection system has been developed in the visualization lab at NETL. This multi-wall system consists of four projection screens, three of which are tiled into four quadrants. The graphics for the multi-wall system are rendered using a cluster of eight personal computers. A high-level visualization interface named Mavis has also been developed to combine the powerful 3D modules of OpenDX with methods developed at NETL for studying multiphase CFD data. With Python, a completely new OpenDX user interface was built that extends and simplifies the features of a basic graphics library.

Airflow and Cooling in a Data Center

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Suhas V. Patankar
Keyword(s):  
Fluid Dynamics ◽  
Data Center ◽  
Cfd Simulations ◽  
Flow Rates ◽  
Factors Affecting ◽  
Hot Air ◽  
Airflow Distribution ◽  
Computational Fluid Dynamics Cfd ◽  
Cooling Air ◽  
Insight Into

This paper deals with the distribution of airflow and the resulting cooling in a data center. First, the cooling challenge is described and the concept of a raised-floor data center is introduced. In this arrangement, cooling air is supplied through perforated tiles. The flow rates of the cooling air must meet the cooling requirements of the computer servers placed next to the tiles. These airflow rates are governed primarily by the pressure distribution under the raised floor. Thus, the key to modifying the flow rates is to influence the flow field in the under-floor plenum. Computational fluid dynamics (CFD) is used to provide insight into various factors affecting the airflow distribution and the corresponding cooling. A number of ways of controlling the airflow distribution are explored. Then attention is turned to the above-floor space, where the focus is on preventing the hot air from entering the inlets of computer serves. Different strategies for doing this are considered. The paper includes a number of comparisons of measurements with the results of CFD simulations.

scholarly journals The Efficient Application of an Impulse Source Wavemaker to CFD Simulations

2019 ◽  
Author(s):  
Pál Schmitt ◽  
Christian Windt ◽  
Josh Davidson ◽  
John V. Ringwood ◽  
Trevor Whittaker
Keyword(s):  
Shallow Water ◽  
Source Function ◽  
Cfd Simulation ◽  
Navier Stokes ◽  
Cfd Simulations ◽  
Wide Range ◽  
Rans Models ◽  
Hydrodynamic Processes ◽  
Computational Fluid Dynamics Cfd ◽  
Shallow Water Models

Computational Fluid Dynamics (CFD) simulations, based on Reynolds Averaged Navier Stokes (RANS) models, are a useful tool for a wide range of coastal and offshore applications, providing a high fidelity representation of the underlying hydrodynamic processes. Generating input waves in the CFD simulation is performed by a numerical wavemaker (NWM), with a variety of different NWM methods existing for this task. While NWMs, based on impulse source methods, have been widely applied for wave generation in depth averaged, shallow water models, they have not seen the same level of adoption in the more general RANS based CFD simulations, due to difficulties in relating the required impulse source function to the resulting free surface elevation for non-shallow water cases. This paper presents an implementation of an impulse source wavemaker, which is able to self-calibrate the impulse source function to produce a desired wave series in deep or shallow water at a specific point in time and space. Example applications are presented, for a numerical wave tank (NWT), based on the opensource CFD software OpenFOAM, for wave packets in deep and shallow water, highlighting the correct calibration of phase and amplitude. Also, the suitability for cases requiring very low reflection from NWT boundaries is demonstrated. Possible issues in the use of the method are discussed and guidance for good application is given.

CFD Simulation of Slug Dissipation in an Enlarged Impacting Tee

2019 ◽  
Author(s):  
Mobina Mohammadikharkeshi ◽  
Mazdak Parsi ◽  
Ramin Dabirian ◽  
Ram S. Mohan ◽  
Ovadia Shoham
Keyword(s):  
Experimental Data ◽  
Void Fraction ◽  
Cfd Simulation ◽  
Petroleum Industry ◽  
Production Operation ◽  
Cfd Simulations ◽  
Ansys Fluent ◽  
Transient Model ◽  
Diameter Pipe ◽  
Computational Fluid Dynamics Cfd

Abstract Slug flow, which commonly occurs in the petroleum industry, is not always a desired flow pattern due to production operation problems it may cause in pipelines and processing facilities. To mitigate these problems, flow conditioning devices such as multiphase flow manifolds and slug catchers are used, where dissipation of slugs occurs in downward flow or in larger diameter pipe sections. Tee-junctions are important parts of these flow conditioning devices. In this work, Computational Fluid Dynamics (CFD) simulations are conducted using ANSYS/FLUENT 17.2 to investigate slug dissipation in an Enlarged Impacting Tee-Junction (EIT). An Eulerian–Eulerian MultiFluid VOF transient model in conjunction with the standard k-ε turbulent model is used to simulate slug dissipation in an EIT geometry. The EIT consists of a 0.05 m ID 10 m long inlet, which is connected to the center of a 0.074 m ID 5.5 m long section that forms the EIT branches. Moreover, experimental data are acquired on slug dissipation lengths in a horizontal EIT with a similar geometry as in the CFD simulations. The CFD results include the mean void fraction and cross-sectionally averaged void fraction time series in the EIT for different gas and liquid velocities. These results provide the inlet slug length and dissipation length in the EIT branches. The CFD results are evaluated against the experimental data demonstrating that the slug dissipation occurring in EIT branches can be predicted by simulation.

CFD Simulation of Segregation in Particulate Multiphase Flows With Binary Solids

2005 ◽  
Author(s):  
Zuoxin Hao
Keyword(s):  
Multiphase Flow ◽  
Cfd Simulation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Primary Objective ◽  
Cfd Simulations ◽  
Separation Processes ◽  
Solid Mixture ◽  
Computational Fluid Dynamics Cfd ◽  
Realistic Prediction

Segregation in particulate multiphase flow with binary solid mixture has extensive applications in industrial separation processes. Up to now there have been few attempts towards numerical simulation of segregation in particulate multiphase flow with binary mixture due to complexity of the problem. In view of this, the primary objective of present work is to simulate the problem by computational fluid dynamics (CFD) and to validate by comparison with experimental measurements. Eulerian-Eulerian approach, incorporating the granular temperature, an essential ingredient in the solids pressure and solids viscosity formulation, was used to model the flow field of multiphase flow and was solved by Fluent 6.0. The CFD simulation results have been validated by experiments of liquid fluidization of binary solid mixtures. Validation results show that CFD simulation predict segregation and solid volume fraction profile precisely, and in addition, it can supply a more realistic prediction of other hydrodynamic features of the multiphase flow, such as velocity vector of all phases and pressure drop. The success of such CFD simulations opens doors for many potential studies.

CFD and Experimental Analysis of Centrifugal Fans With Forward Curved Blades Used in Electric Motors

2019 ◽  
Author(s):  
S. S. Borges
Keyword(s):  
Cfd Simulation ◽  
Experimental Tests ◽  
Performance Comparison ◽  
Centrifugal Fan ◽  
Electric Motors ◽  
Cfd Simulations ◽  
Interface Models ◽  
Ansys Cfx ◽  
Centrifugal Fans ◽  
Computational Fluid Dynamics Cfd

Abstract This work presents an analysis of the aerodynamic performance of a centrifugal fan with forward curved blades (Sirocco) applied to electric motors. In this analysis were carried out computational fluid dynamics (CFD) simulations and experimental tests for comparison of results. The focus of this analysis is the performance comparison among three different models of general connection interface that are required for the connection between the grids of the rotating and stationary domains of CFD simulation, considering the method adopted by the Ansys CFX, software used as computational tool. Thereby, Frozen Rotor, Stage, and Transient Rotor-Stator were the interface models evaluated. For comparison reference, the experimental data were used to evaluate the performance of each interface models for overall operating range of the fan.

scholarly journals AP-IO: Asynchronous Pipeline I/O for Hiding Periodic Output Cost in CFD Simulation

2014 ◽  
Vol 2014 ◽  
pp. 1-12
Author(s):  
Ren Xiaoguang ◽  
Xu Xinhai
Keyword(s):  
Cfd Simulation ◽  
Massively Parallel ◽  
Optimization Scheme ◽  
Total Execution Time ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Application Characteristics ◽  
Asynchronous Pipeline ◽  
User Friendly ◽  
Parallel Cfd

Computational fluid dynamics (CFD) simulation often needs to periodically output intermediate results to files in the form of snapshots for visualization or restart, which seriously impacts the performance. In this paper, we present asynchronous pipeline I/O (AP-IO) optimization scheme for the periodically snapshot output on the basis of asynchronous I/O and CFD application characteristics. InAP-IO, dedicated background I/O processes or threads are in charge of handling the file write in pipeline mode, therefore the write overhead can be hidden with more calculation than classic asynchronous I/O. We design the framework ofAP-IOand implement it in OpenFOAM, providing CFD users with a user-friendly interface. Experimental results on theTianhe-2supercomputer demonstrate thatAP-IOcan achieve a good optimization effect for the periodical snapshot output in CFD application, and the effect is especially better for massively parallel CFD simulations, which can reduce the total execution time up to about 40%.

scholarly journals Prediction of Wind Erosion over a Heritage Site: A Case Study of Yongling Mausoleum, China

2019 ◽  
Vol 3 (4) ◽  
pp. 41-57
Author(s):  
Xiaoyu Wang ◽  
Jinzhu Meng ◽  
Tianwei Zhu ◽  
Jingyu Zhang
Keyword(s):  
Wind Erosion ◽  
Cfd Simulation ◽  
Scale Model ◽  
Weather Data ◽  
Cfd Simulations ◽  
Wind Speeds ◽  
Heritage Site ◽  
Heritage Buildings ◽  
Computational Fluid Dynamics Cfd

AbstractTo protect heritage buildings better, a method exploiting computational fluid dynamics (CFD) was developed for the analysis of wind erosion at a heritage site. Over a two-year period, we collected measurements of hourly weather data at Xinbin County to obtain statistics of wind speeds and directions for the Yongling Mausoleum. Subsequent results from CFD simulations show that before greening, with wind speeds reaching 10 m/s, certain structures (southwest-facing corners, doors and windows on open sides, places where swirling winds develop, and eaves of sloping roofs) of four heritage buildings were eroded more severely. With appropriate greening, plants may exert their unique ecological presence to better protect heritage buildings and their historical environments. After greening, the severity of damage to these vulnerable structures by wind was reduced. With wind speeds reaching 10 m/s, the average pressure on the structures of each building was 0.41–27.85 Pa, representing a reduction of 2.4%–75.6% from pressures before greening. We also constructed a 1:500-scale model to verify in experiments the correctness of CFD simulation qualitatively. The CFD simulations were found to provide an effective method to investigate and predict wind erosion of the heritage site.

Influence of Jordanian zeolite on the performance of a solar still: experiments and CFD simulation studies

2016 ◽  
Vol 16 (6) ◽  
pp. 1700-1709 ◽  
Author(s):  
Yazan Taamneh
Keyword(s):  
Experimental Data ◽  
Phase Change ◽  
Cfd Simulation ◽  
Volume Fraction ◽  
Solar Still ◽  
Cfd Simulations ◽  
Two Phase ◽  
Vof Model ◽  
Computational Fluid Dynamics Cfd ◽  
Good Agreement

Computational fluid dynamics (CFD) simulations were performed for experiments carried out with two identical pyramid-shaped solar stills. One was filled with Jordanian zeolite-seawater and the second was filled with seawater only. This work is focused on CFD analysis validation with experimental data conducted using a model of phase change interaction (evaporation-condensation model) inside the solar still. A volume-of-fluid (VOF) model was used to simulate the inter phase change through evaporation-condensation between zeolite-water and water vapor inside the two solar stills. The effect of the volume fraction of the zeolite particles (0 ≤ ϕ ≤ 0.05) on the heat and distillate yield inside the solar still was investigated. Based on the CFD simulation results, the hourly quantity of freshwater showed a good agreement with the corresponding experimental data. The present study has established the utility of using the VOF two phase flow model to provide a reasonable solution to the complicated inter phase mass transfer in a solar still.

Sign in / Sign up

Export Citation Format

Share Document