Tribological behaviour of graphene oxide sheets as lubricating additives in bio-oil

2018 ◽  
Vol 70 (8) ◽  
pp. 1396-1401 ◽  
Author(s):  
Daoyi Wu ◽  
Yufu Xu ◽  
Lulu Yao ◽  
Tao You ◽  
Xianguo Hu
Keyword(s):  
Graphene Oxide ◽  
Friction Coefficient ◽  
Wear Loss ◽  
Tribological Behaviour ◽  
Low Friction ◽  
Content Type ◽  
Base Oil ◽  
Lubricating Film ◽  
Bio Oil ◽  
Practical Implications

Purpose This paper aims to study the upgradation of the lubricating performance of the renewable base oil , and to study the tribological behavior of graphene oxide (GO) sheets used as lubricating additives in bio-oil for iron/steel contact. Design/methodology/approach A multifunctional end-face tribometer was used to characterize the friction coefficient and wear loss of the tribosystem under different lubricants. Findings The experimental results show that GO sheets with small size benefit lubricating effects and the optimal concentration of GO sheets in bio-oil is 0.4-0.6 per cent, which can form a complete lubricating film on the frictional interfaces and obtain a low friction coefficient and wear loss. Higher concentration of GO sheets can result in a significant aggregation of the sheets, reducing the content of the lubricating components in the bio-oil, which results in the increase in friction and wear; at this stage, the main wear pattern was ascribed to adhesive wear. Practical implications These results show a promising prospect of improving the tribological performance of renewable base oil with the introduction of GO sheets as additives. Originality/value No literature has covered the tribological behaviour of GO sheets in bio-oil. This study contributes to accelerating the application of bio-oil.

Tribological behaviour of calcium grease containing carbon nanotubes additives

2016 ◽  
Vol 68 (6) ◽  
pp. 723-728 ◽  
Author(s):  
Bahaa M. Kamel ◽  
Alaa Mohamed ◽  
M. El Sherbiny ◽  
K.A. Abed
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Friction Coefficient ◽  
Average Diameter ◽  
Tribological Behaviour ◽  
Wear Scar Diameter ◽  
Content Type ◽  
X Ray ◽  
Lubricating Film ◽  
Multi Walled Carbon Nanotubes

Purpose The purpose of this paper is to fabricate composite nanogrease for tribological applications. Multi-walled carbon nanotubes (MWCNTs) with a size 10 nm average diameter and 5 μm in length were used as additives to calcium grease. Design/methodology/approach The tribological four-ball machine was used to evaluate calcium grease with carbon nanotubes (CNTs) as an additive. The interaction between CNT and calcium grease (nanogrease) were studied by transmission electron microscopy and X-ray diffraction. Findings MWCNTs composite nanogrease was manufactured for tribological applications. The effectiveness of the fabricated grease in improving the tribological performance at different concentrations and under different loads was tested. The results are summarized as follows. CNT nanoparticle additive dispersed in calcium grease significantly improve its anti-wear performance, reducing friction, increasing load-carrying capacity and extreme pressure (EP) property. The friction is reduced by about 50 per cent, the wear scar diameter (WSD) decreased to 32 per cent and the EP properties increases about 38 per cent, with only 3 wt.%. The modified grease with CNTs additives of 3 wt.% showed the most favorable results. Energy dispersive x-ray (EDX) analysis shows that C was present on the worn scar surface, with atomic concentration of about 22 per cent. The presence of C suggests that a lubricating film is likely formed because of the presence of CNTs and very likely prevented the steel-to-steel direct contact. Originality/value The results indicated that a 3 wt.% of MWCNT nanogrease is an excellent antiwear, with EP and low friction coefficient. It was also found that the friction coefficient was reduced to about 50 per cent, the WSD decreased by about 32 per cent and the EP properties increased about 38 per cent. The mating surfaces were investigated with scanning electron microscopy and EDX. The results show that a boundary film mainly composed of CNTs, Cr and Fe was formed on the rubbed surfaces.

Tribological performance of self-lubricated polyamide6/boric oxide composites after water conditioning

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Kawaljit Singh Randhawa ◽  
Ashwin Patel
Keyword(s):  
Friction Coefficient ◽  
Abrasion Resistance ◽  
Tribological Performance ◽  
Boric Oxide ◽  
Resistance Testing ◽  
Tribological Behaviour ◽  
Content Type ◽  
Wear Rates ◽  
Water Conditioning ◽  
Oxide Composites

Purpose This paper aims to investigate the tribological performance, i.e. abrasion resistance, friction coefficient and wear rates, of self-lubricated water conditioned polyamide6/boric oxide composites. Design/methodology/approach Polyamide6 and polyamide6/boric oxide self-lubricated composites were immersed in water for 15 days to analyze the effect of water conditioning on friction, wear and abrasion resistance. Tribological testing on pin-on-disc tribometer and abrasion resistance testing on TABER abrader were performed to see the friction coefficient and wear rates of materials. The scanning electron microscopy (SEM) characterizations were performed to analyze the wear tracks. Findings Tribological testing results revealed the loss in abrasive resistance, but there was an improvement in frictional coefficient and wear rates with steel after water absorption. The SEM images clearly show less depth of wear tracks in water-conditioned materials than dry ones. Water conditioning was found supportive in the formation of smooth lubricating transfer film on steel disc during the tribological testing. Originality/value The tribological behaviour of polymer composites is different in dry and in high humidity or water conditions. Experiments were performed to investigate B2O3 solid lubricant filler effectiveness on tribological behaviour of water-conditioned polyamide composites. Bonding between polyamide6 and water molecules plus the formation of orthoboric acid was found advantageous in decreasing the friction coefficient and wear rates of composites.

Surfaces with pores: hydrodynamic lubrication

2017 ◽  
Vol 69 (4) ◽  
pp. 471-483 ◽  
Author(s):  
Leonid Burstein
Keyword(s):  
Design Methodology ◽  
Hydrodynamic Lubrication ◽  
Dimensional Model ◽  
Hydrodynamic Behavior ◽  
Content Type ◽  
One Dimensional ◽  
Lubricating Film ◽  
Cell Dimensions ◽  
Practical Implications ◽  
Pore Cell

Purpose This paper aims to assess the hydrodynamic lubrication of two opposing surfaces with identical pores having a semicircular profile. The surfaces are treated with more than one pore that allows clarification of whether there exists interaction between the pores. Design/methodology/approach A transient, spatial, one-dimensional model of surfaces with regular pores was developed and applied in the context of fluid lubrication. MATLAB software has been used. Findings Calculations show that a lubricating film between two surfaces with pores provides better hydrodynamic conditions in comparison to that on one surface with pores. It was also shown that the pores of one surface act as separate objects and can take into account only the interaction between the pores of the opposite surfaces. In addition, it was found that there are optimum values of the pore radii, gap and pore cell dimensions at which the bearing capacity of the film is maximal. Practical implications The computer program used for the pore parameter calculations provided the optimal lubrication. Originality/value This is the first study of the lubricating film hydrodynamic behavior of two opposite surfaces with pores having a semicircular profile.

Tribological behavior of UHMWPE in water lubrication: the effect of molding temperature

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Xincong Zhou ◽  
Chaozhen Yang ◽  
Jian Huang ◽  
Xueshen Liu ◽  
Da Zhong ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Friction Coefficient ◽  
Friction And Wear ◽  
Wear Loss ◽  
Content Type ◽  
Molding Temperature ◽  
Melting Temperatures ◽  
Ultra High Molecular Weight ◽  
Wear Tests ◽  
Friction And Wear Tests

Purpose Ultra-high molecular weight polyethylene (UHMWPE) is adopted in water-lubricated bearings for its excellent performance. This paper aims to investigate the tribological properties of UHMWPE with a molecular weight of 10.2 million (g mol‐1) under different molding temperatures. Design/methodology/approach The UHMWPE samples were prepared by mold pressing under constant pressure and different molding temperatures (140°C, 160°C, 180°C, 200°C, 220°C). The friction and wear tests in water were conducted at the RTEC tribo-tester. Findings The friction coefficient and wear loss decreased first and rose later with the increasing molding temperature. The minimums of the friction coefficient and wear loss were found at the molding temperatures of 200°C. At low melting temperatures, the UHMWPE molecular chains could not unwrap thoroughly, leading to greater abrasive wear. On the other hand, high melting temperatures will cause the UHMWPE molecular chains to break up and decompose. The optimal molding temperatures for UHMWPE were found to be 200°C. Originality/value Findings are of great significance for the design of water-lubricated UHMWPE bearings.

Prediction of Wear Rate Dispersion in Mixed Lubrication

2005 ◽  
Author(s):  
F. Robbe-Valloire ◽  
R. Progri ◽  
B. Paffoni ◽  
R. Gras
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Boundary Lubrication ◽  
Mixed Lubrication ◽  
Tribological Behaviour ◽  
Low Friction ◽  
Local Boundary ◽  
Physico Chemical ◽  
Lubricant Films ◽  
Second Category

Mixed lubrication is usually related to the partition of contacts, and these latter may be divided into two categories. The first includes all asperities working in thin lubricated film (physico-chemical film) conditions. This situation corresponds to local boundary lubrication and is characterised by a local friction coefficient around 0.1. The second category contains all other asperity types. Due to the existence of a thick lubricant films asperities belonging to the second category exhibit a low friction coefficient. The global tribological behaviour for a given contact, however, is function of both categories, since it involves asperities from both categories.

Research on Lubrication and Wear-Resistant Mechanism of Ni60A/MoS2 Composite Coating

2011 ◽  
Vol 189-193 ◽  
pp. 231-235
Author(s):  
Yun Cai Zhao ◽  
Li Wang
Keyword(s):  
Friction Coefficient ◽  
Composite Coating ◽  
Friction Surface ◽  
Testing Machine ◽  
The Self ◽  
Wear Testing ◽  
Friction Property ◽  
Low Friction ◽  
Coverage Area ◽  
Lubricating Film

The influence of MoS2 lubrication phase on the tribological properties of the Ni60A/MoS2 composite coating was conducted on UMT-2 micro-wear testing machine (USA), discussing the self-lubricating effect and mechanism. The result shows that with the increasing content of MoS2, the friction coefficient of the coating which changed with the increasing content of the MoS2 presents firstly decreases then increases, and the value reach the minimum when the quality percent of MoS2 wrapped with Nickel is 35%. Low-friction property of the Ni60A/MoS2 composite coating is due to the forming of MoS2 lubricating film in friction surface. The decreasing of the friction coefficient of the coating is in proportion to the coverage area of MoS2 lubricating film.

Sliding Wear Characteristics and Fabrication of LPS-SIC Ceramic by Sintering Additives

2007 ◽  
Vol 345-346 ◽  
pp. 1541-1544
Author(s):  
Han Ki Yoon ◽  
Sung Ho Park ◽  
Won Jo Park
Keyword(s):  
Friction Coefficient ◽  
Gas Turbines ◽  
Sliding Wear ◽  
Sintering Temperature ◽  
High Hardness ◽  
Wear Loss ◽  
Low Friction ◽  
Wear Characteristics ◽  
Sic Ceramic ◽  
High Temperature Components

Silicon carbide (SiC) materials have been extensively studied for high-temperature components in fusion blanket system and gas turbines, because they have excellent a hightemperature mechanical properties, high thermal conductivity and wear resistance. However, the brittle characteristics of SiC such as low strain-to fracture still impose a severe limitation on the practical application of SiC materials. Therefore, a study of the sliding wear characteristics and fabrication of SiC ceramic by sintering temperature and additives are need. As the result of abrasion, the friction coefficient of the monolithic SiC sintered at 1800°C was the lowest, and the friction coefficient of that sintered at 1760°C was the highest. The monolithic SiC manufactured at 1800°C showed the highest hardness and the lowest friction coefficient. The friction coefficient of the monolithic SiC sintered by the SiO2 contents of 2wt% was the lowest, and the friction coefficient that sintered by the SiO2 contents of 5wt% was the highest. 1800°C of sintering temperature and 2wt% of SiO2 contents ware shown high hardness, low friction coefficient and wear loss compare with other temperatures and SiO2 contents.

The study of friction layer and tribological property of PI–matrix composites

2017 ◽  
Vol 69 (2) ◽  
pp. 267-275 ◽  
Author(s):  
Xiulin Xu ◽  
Xing Lu ◽  
Zuoxiang Qin ◽  
Dalong Yang
Keyword(s):  
Friction Coefficient ◽  
Tribological Property ◽  
Wear Debris ◽  
Friction Pair ◽  
Matrix Composites ◽  
Low Friction ◽  
Friction Layer ◽  
Content Type ◽  
Compact Zone ◽  
Pin On Disk

Purpose This paper aims to study the friction layer and tribological property of polyimide (PI)–matrix composites under different friction speeds. Design/methodology/approach Friction tests were conducted under friction speeds ranging from 20-120 km/h and pressure of 0.57 MPa by a pin-on-disk tribometer. Findings The results indicate that the friction coefficient decreases with the increasing of the friction speed. Under different friction speeds, the structure of the friction layer and debris are different, which affects the actual tribological performance of the composites. At low friction speed, the morphology of the friction layer is mainly particulate. The higher level of clenching action between the friction pair leads to a high friction coefficient, and the morphology of the particles in the particulate zone and the wear debris are mostly equiaxial particles. At high friction speed, the morphology of the friction layer is mainly a compact zone. The reduction of the surface roughness leads to a low friction coefficient. The debris collected on the counter surface at high friction speeds are mostly big sheets, and the morphology of the particles in the particulate zone is mostly rod-like. Controlling the conditions of the disk and the pin can reveal the influence of friction speed on the friction layer. The wear mechanisms at different friction speeds are also discussed. Originality/value By controlling the conditions of the disk and the pin to reveal the influence of friction speed on the friction layer, and the evolutions of the friction layer, wear debris were carefully inspected with the aim of demonstrating the relationship between friction speed and wear mechanism of PI–matrix composites.

A study on the wear behavior of tin-based journal bearing under different working conditions

2019 ◽  
Vol 72 (3) ◽  
pp. 359-368
Author(s):  
Hulin Li ◽  
Zhongwei Yin ◽  
Yanzhen Wang
Keyword(s):  
Friction Coefficient ◽  
Abrasive Wear ◽  
Working Conditions ◽  
Wear Mechanisms ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Wear Loss ◽  
Fatigue Wear ◽  
Content Type

Purpose The purpose of this paper is to study the friction and wear properties of journal bearings under different working conditions. Design/methodology/approach Friction coefficient and wear losses of journal bearing under different working conditions have been determined by a bearing test rig. The worn surfaces of bearing were examined by scanning electron microscopy and laser three-dimensional micro-imaging profile measurements, and the tribological behavior and wear mechanisms were investigated. Findings The wear loss and friction coefficient of bearing under starting-stopping working condition is far greater than that of steady-state working conditions. In addition, the maximum wear loss under start-up and stop conditions is about 120 times of that under stable operating conditions. Under stable working conditions, the main wear forms of bearings are abrasive wear, under starting-stopping working conditions the main wear mechanisms of bearings are adhesion wear, abrasive wear and fatigue wear. Originality/value These research results have certain practical value for understanding the tribology behavior of journal bearings under different working conditions.

The problems of resistance to scuffing of heavily loaded lubricated friction joints with WC/C-coated parts

2014 ◽  
Vol 66 (3) ◽  
pp. 434-442 ◽  
Author(s):  
Remigiusz Michalczewski ◽  
Witold Piekoszewski ◽  
Waldemar Tuszynski ◽  
Marian Szczerek
Keyword(s):  
Design Methodology ◽  
Solid Lubricant ◽  
Vapour Deposition ◽  
Friction Pair ◽  
Low Friction ◽  
Friction Zone ◽  
Content Type ◽  
Steel Coating ◽  
Uncoated Steel ◽  
Practical Implications

Purpose – The purpose of this paper was to explore the mechanisms of scuffing propagation of heavily loaded lubricated friction pair elements coated with low-friction WC/C coating for various material combinations. Design/methodology/approach – The investigations were performed for low-friction coatings WC/C (a-C:H:W) deposited by the reactive sputtering physical vapour deposition (PVD) process. Experiments were carried out using a four-ball tester with continuously increasing loads. Tests were conducted for the following four material combinations: steel/steel tribosystem (all balls uncoated); steel/coating tribosystem (one upper ball uncoated/three lower balls WC/C-coated); coating/steel tribosystem (one upper ball WC/C-coated/three lower balls uncoated); and coating/coating tribosystem (all balls WC/C-coated). Findings – The better scuffing resistance is achieved by coating only one element (coating/steel tribosystem) than all elements (coating/coating tribosystem). The description of scuffing propagation for all investigated tribosystems was done. The high scuffing resistance of the coating/steel tribosystem resulted from reducing the adhesion between rubbing surfaces due to low chemical affinity (similarities) between the steel and the coating material and the presence of solid lubricant in the friction zone. Practical implications – In all cases, when a coating is applied, an increase in scuffing resistance is observed. However, it is better to coat only one element than all. Furthermore, the scuffing resistance for the coating/steel tribosystem is significantly higher than for the steel/coating tribosystem. Originality/value – The main value of this paper is description of scuffing propagation and revealing the new aspects in application of low-friction WC/C coating for heavily loaded lubricated friction pair elements. The overlapping ratio has been defined as an important factor influencing the scuffing resistance of the coated tribosystems.

Sign in / Sign up

Export Citation Format

Share Document