Design and Closed Loop Testing of High-Pressure Centrifugal Gas Compressors for the Suppression of Subsynchronous Vibration

1980 ◽  
Vol 102 (1) ◽  
pp. 136-140
Author(s):  
A. F. Criqui ◽  
P. G. Wendt

The causative phenomena of subsynchronous vibration, or re-excitation of the critical speed of a rotor, are discussed. Two rotor systems designed to control this type of vibration are presented. One system employs tuned, oil film damper bearings while the other features a stiffened rotor geometry. Stability thresholds of each design are compared based on high-pressure closed loop testing.

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
Yukio Ishida ◽  
Tomonori Matsuura ◽  
Xiao Long Zhang

An automatic ball balancer is a unique vibration suppression device for rotor systems. Theoretically, two balls in a cylindrical chamber of the rotor are located at the optimal positions on the opposite side to the unbalance and cancel the unbalance automatically in the super-critical speed range. However, this device is not used widely due to two malfunctions. One is the influence of friction. Due to the inevitable friction between the balls and the inside wall of the channel, the balls stop near the optimal positions and do not balance the rotor perfectly. The other is the self-excited oscillation which occurs near and above the major critical speed. The objectives of the present paper are to clarify the fundamental characteristics of a ball balancer and to introduce some simple methods to eliminate these malfunctions.


2007 ◽  
Vol 129 (4) ◽  
pp. 904-912 ◽  
Author(s):  
Niels Heinrichson ◽  
Axel Fuerst ◽  
Ilmar Ferreira Santos

This is Part II of a two-part series of papers describing the effects of high-pressure injection pockets on the operating conditions of tilting-pad thrust bearings. The paper has two main objectives. One is an experimental investigation of the influence of an oil injection pocket on the pressure distribution and oil film thickness. Two situations are analyzed: (i) when the high-pressure oil injection is turned off and (ii) when the high-pressure injection is turned on. The other objective is to validate a numerical model with respect to its ability to predict the influence of such a pocket (with and without oil injection) on the pressure distribution and oil film thickness. Measurements of the distribution of pressure and oil film thickness are presented for tilting-pad thrust bearing pads of ∼100cm2 surface area. Two pads are measured in a laboratory test rig at loads of ∼1.5MPa and ∼4.0MPa and velocities of up to 33m∕s. One pad has a plain surface. The other pad has a conical injection pocket at the pivot point and a leading-edge taper. The measurements are compared to theoretical values obtained using a three-dimensional thermoelastohydrodynamic (TEHD) numerical model. At the low load, the theoretical pressure distribution corresponds well with the measured values for both pads, although the influence of the pocket is slightly underestimated. At the high load, large discrepancies exist for the pad with an injection pocket. It is argued that the discrepancies are due mainly to geometric inaccuracies of the collar surface, although they may to some extent be due to the simplifications employed in a Reynolds equation description of the pocket flow. The measured and theoretical values of oil film thickness compare well at low loads and velocities. At high loads and velocities, discrepancies grow to up to 25%. This is due to the accuracy of the measurements. When using hydrostatic jacking the model predicts the start-up behavior well.


Atmosphere ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 307
Author(s):  
Makoto Inoue ◽  
Atsushi Ugajin ◽  
Osamu Kiguchi ◽  
Yousuke Yamashita ◽  
Masashi Komine ◽  
...  

In this study, we investigated the effects of the Tibetan High near the tropopause and the North Pacific High in the troposphere on occurrences of hot or cool summers in Japan. We first classified Japan into six regions and identified hot and cool summer years in these regions from a 38-year sample (1980–2017) based on the monthly air temperature. To investigate the features of circulation fields over Asia during hot and cool summers in Japan, we calculated the composite differences (hot summer years minus cool summer years) of several variables such as geopotential height, which indicated significant high-pressure anomalies in the troposphere and lower stratosphere. These results suggest that both the North Pacific and the Tibetan Highs tend to extend to Japan during hot summer years, while cool summers seem to be associated with the weakening of these highs. We found that extension of the Tibetan High to the Japanese mainland can lead to hot summers in Northern, Eastern, and Western Japan. On the other hand, hot summers in the Southwestern Islands may be due to extension of the Tibetan High to the south. Similarly, the latitudinal direction of extension of the North Pacific High is profoundly connected with the summer climate in respective regions.


2014 ◽  
Vol 541-542 ◽  
pp. 658-662
Author(s):  
Jian Li ◽  
Yuan Chen ◽  
Yang Chun Yu ◽  
Zhu Xin Tian ◽  
Yu Huang

To study the velocity and pressure distribution of the oil film in a heavy hydrostatic thrust bearing, a mathematical model of the velocity is proposed and the finite volume method (FVM) has been used to simulate the flow field under different working conditions. Some pressure experiments were carried out and the results verified the correctness of the simulation. It is concluded that the pressure distribution varies small under different rotation speed when the surface load on the workbench is constant. But the velocity of the oil film is influenced greatly by the rotation speed. When the rotation speed of the workbench is as quick as enough, the velocity of the oil film on one radial side of the pad will be zero, that is to say the lubrication oil will be drained from the other three sides of the recess.


2001 ◽  
Vol 15 (18) ◽  
pp. 2491-2497 ◽  
Author(s):  
J. L. ZHU ◽  
L. C. CHEN ◽  
R. C. YU ◽  
F. Y. LI ◽  
J. LIU ◽  
...  

In situ high pressure energy dispersive X-ray diffraction measurements on layered perovskite-like manganate Ca 3 Mn 2 O 7 under pressures up to 35 GPa have been performed by using diamond anvil cell with synchrotron radiation. The results show that the structure of layered perovskite-like manganate Ca 3 Mn 2 O 7 is unstable under pressure due to the easy compression of NaCl-type blocks. The structure of Ca 3 Mn 2 O 7 underwent two phase transitions under pressures in the range of 0~35 GPa. One was at about 1.3 GPa with the crystal structure changing from tetragonal to orthorhombic. The other was at about 9.5 GPa with the crystal structure changing from orthorhombic back to another tetragonal.


2004 ◽  
Vol 68 (1) ◽  
pp. 83-100 ◽  
Author(s):  
E. Salvioli-Mariani ◽  
L. Toscani ◽  
D. Bersani

AbstractThe lamproite of Gaussberg is an ultrapotassic rock where leucite, olivine and clinopyroxene microphenocrysts occur in a glass-rich groundmass, containing microliths of leucite, clinopyroxene, apatite, phlogopite and rare K-richterite.Abundant silicate melt inclusions occur in olivine, leucite and, rarely, in clinopyroxene microphenocrysts. Raman investigations on melt inclusions showed the presence of pure CO2 in the shrinkage bubbles. On the other hand, the glass of the groundmass is CO2-poor and contains up to 0.70 wt.% of dissolved H2O, as estimated by infrared spectra. It is inferred that CO2 was released at every stage of evolution of the lamproite magma (CO2-rich shrinkage bubbles), whereas H2O was retained for longer in the liquid. At Gaussberg, CO2 seems to have a major role at relatively high pressure where it favoured the crystallization of H2O-poor microphenocrysts; the uprise of the magma to the surface decreased the solubility of CO2 and caused a relative increase in water activity. As a consequence, phlogopite and K-richterite appeared in the groundmass.The glass composition of both the groundmass and melt inclusions suggests different evolutions for the residual liquids of the investigated samples. Sample G886 shows the typical evolution of a lamproite magma, where the residual liquid evolves toward peralkaline and Na-rich composition and crystallizes K-richterite in the latest stage. Sample G895 derives from mixing/mingling of different batches of magma; effectively glasses from melt inclusions in leucite and clinopyroxene are more alkaline than those found in early crystallized olivine. Leucite and clinopyroxene crystallized early from a relatively more alkaline batch of lamproite magma and, successively, a less alkaline, olivinebearing magma batch assimilated them during its rise to the surface.


2014 ◽  
Vol 900 ◽  
pp. 734-737 ◽  
Author(s):  
Huai Chao Wu ◽  
Yun Liu Yu

The stress and strain of the slipper of 35 MPa high pressure axial piston pump are analyzed by the finite element analysis method, and the following facts are revealed: in spite of the fact that the slipper can satisfy the use requirement in the aspect of stress, whereas, in the aspect of strain, the deformation of the bottom of the slipper increases with the pressure increase, and the deformation of the slipper has reached the order of magnitude of the oil film thickness under 35 MPa working pressure. Therefore, when the slipper pair of 35 MPa high pressure axial piston pump is designed and its oil film performances are studied, the influence of deformation of the slipper on the oil film structure must be considered comprehensively. The results of this study can provide some guides for developing 35 MPa high pressure axial piston pump.


2005 ◽  
Vol 127 (6) ◽  
pp. 1191-1197 ◽  
Author(s):  
Yasuo Fujioka ◽  
Tomotsugu Sakai

Structures composed of a rotary disk and a shaft, which are fastened with bolts and nuts having tapered bearing surfaces, are loaded with a rotating-bending force. Upon investigation, two rotating mechanisms of the nut were derived. In one mechanism a high-pressure contact area is formed at the nearest loading point on threads and bearing surfaces. This leads to a difference in the curvature radii between the bearing surface of the disk and that of the nut. During the revolution of the disk, two friction torques occur in opposite directions on the bearing surface and the threads, respectively. The relative rotating direction of the nut is dominated by the greater torque. The other mechanism is due to the eccentricities caused by dimensional errors of the bolt, nut, and disk. By combining the two mechanisms, the rotations of the nuts either cause a loosening or tightening after many revolutions of the disk.


1963 ◽  
Vol 4 (36) ◽  
pp. 809-812
Author(s):  
R. L. Shreve

AbstractIn August 1961 an aluminum pipe (3.5 cm. internal diameter, 4.2 cm. external diameter) having 92 specially modified socket couplings (5.0 cm. external diameter) sealed with a quick-polymerizing synthetic rubber was sunk 226 m. in a vertical water-filled bore hole in Blue Glacier, Washington. U.S.A. The geometry of threads and mating surfaces of pipe and coupling was designed to cause increasing external water pressure to tighten the seal. One joint at a depth of 66 m. immediately developed an extremely slow leak (probably because of faulty cleaning), but the other 91 joints apparently were sound, as the pipe was free of water to a depth of at least 157 m. when resurveyed after one year.


Sign in / Sign up

Export Citation Format

Share Document