Acoustic Emission From a Brief Crack Propagation Event

1979 ◽  
Vol 46 (1) ◽  
pp. 107-112 ◽  
Author(s):  
J. D. Achenbach ◽  
J. G. Harris

Acoustic emissions produced by elementary processes of deformation and fracture at a crack edge are investigated on the basis of elastodynamic ray theory. To obtain a two-dimensional canonical solution we analyze wavefront motions generated by an arbitrary distribution of climbing edge dislocations emanating from the tip of a semi-infinite crack in an unbounded linearly elastic solid. These wavefront results are expressed in terms of emission coefficients which govern the variation with angle, and phase functions which govern the intensity of the wavefront signals. Explicit expressions for the emission coefficients are presented. The coefficients have been plotted versus the angle of observation, for various values of the crack propagation speed. The phase functions are in the form of integrals over the emanating dislocation distributions. Specific dislocation distributions correspond to brittle fracture and plastic yielding at the crack tip, respectively. Acoustic emission is most intense for brittle fracture, when the particle velocities experience wavefront jumps which are proportional to the stress-intensity factors prior to fracture. An appropriate adjustment of the canonical solution accounts for curvature of a crack edge. Such effects as focussing, finite duration of the propagation event, and finite dimensions of the crack are briefly discussed. As a specific example, the first signals generated by brittle Mode I propagation of an elliptical crack are calculated.

1973 ◽  
Vol 12 (64) ◽  
pp. 144-146 ◽  
Author(s):  
W. F. St. Lawrence ◽  
T. E. Lang ◽  
R.L. Brown ◽  
C. C. Bradley

AbstractAcoustic emissions in the audio spectrum are reported from observations of laboratory experiments conducted on snow samples in uniaxial compression. A number of tests show the pattern of acoustic emissions to be a function of the rate of deformation. Over the frequency range 20 to 7 000 Hz acoustic emissions are associated with rates of deformation corresponding to brittle fracture of the snow sample. Though probably present, no acoustic emissions were detected from samples deforming plastically.


1984 ◽  
Vol 51 (1) ◽  
pp. 77-83 ◽  
Author(s):  
J. G. Harris ◽  
J. Pott

The surface motions excited by acoustic emissions produced by fracture processes at the edge of a buried, penny-shaped crack are investigated. Firstly, wave-front approximations to the emissions generated by the sudden growth of a tensile crack in an unbounded elastic solid are reviewed. Then these approximations are Fourier transformed to give the high-frequency portion of their spectra. Secondly, time and frequency-domain approximations to the surface motions excited by this growing crack, when it is buried in a half-space, are calculated. These results are then scrutinized to elucidate what parts of the signals measured at the surface carry information about the crack’s size, its orientation, and the fracture processes near the crack tip.


1973 ◽  
Vol 12 (64) ◽  
pp. 144-146 ◽  
Author(s):  
W. F. St. Lawrence ◽  
T. E. Lang ◽  
R.L. Brown ◽  
C. C. Bradley

Abstract Acoustic emissions in the audio spectrum are reported from observations of laboratory experiments conducted on snow samples in uniaxial compression. A number of tests show the pattern of acoustic emissions to be a function of the rate of deformation. Over the frequency range 20 to 7 000 Hz acoustic emissions are associated with rates of deformation corresponding to brittle fracture of the snow sample. Though probably present, no acoustic emissions were detected from samples deforming plastically.


2003 ◽  
Vol 805 ◽  
Author(s):  
Frohmut Rösch ◽  
Christoph Rudhart ◽  
Peter Gumbsch ◽  
Hans-Rainer Trebin

ABSTRACTThe propagation of mode I cracks in a three-dimensional icosahedral model quasicrystal has been studied by molecular dynamics techniques. In particular, the dependence on the plane structure and the influence of clusters have been investigated. Crack propagation was simulated in planes perpendicular to five-, two- and pseudo-twofold axes of the binary icosahedral model.Brittle fracture without any crack tip plasticity is observed. The fracture surfaces turn out to be rough on the scale of the clusters. These are not strictly circumvented, but to some extent cut by the dynamic crack. However, compared to the flat seed cracks the clusters are intersected less frequently. Thus the roughness of the crack surfaces can be attributed to the clusters, whereas the constant average heights of the fracture surfaces reflect the plane structure of the quasicrystal. Furthermore a distinct anisotropy with respect to the in-plane propagation direction is found.


2011 ◽  
Vol 105-107 ◽  
pp. 2179-2182
Author(s):  
Wei Min Zhang ◽  
Shu Xuan Liu ◽  
Yong Qiu ◽  
Cheng Feng Chen

Crack propagation is the main reason which leads to the invalidity of the metal components. A set of detecting equipment based on the acoustic emission method was designed, and it was mainly composed of acoustic emission sensor, signal operating circuits and signal acquisition system. Specimens of 16MnR material were manufactured and the static axial tension test of them was carried on. Acoustic emission signals from the specimen were detected by acoustic emission equipment by using piezoelectric ceramic sensor. Signal datum were acquired and operated by the acquisition system, as well as the acquisition program written for it. The final results has demonstrated that acoustic emission equipment designed for the test performed well in acquiring the signals induced by the metal crack propagation.


Author(s):  
A. Albers ◽  
M. Dickerhof

The application of Acoustic Emission technology for monitoring rolling element or hydrodynamic plain bearings has been addressed by several authors in former times. Most of these investigations took place under idealized conditions, to allow the concentration on one single source of emission, typically recorded by means of a piezoelectric sensor. This can be achieved by either eliminating other sources in advance or taking measures to shield them out (e. g. by placing the acoustic emission sensor very close to the source of interest), so that in consequence only one source of structure-born sound is present in the signal. With a practical orientation this is often not possible. In point of fact, a multitude of potential sources of emission can be worth considering, unfortunately superimposing one another. The investigations reported in this paper are therefore focused on the simultaneous monitoring of both bearing types mentioned above. Only one piezoelectric acoustic emission sensor is utilized, which is placed rather far away from the monitored bearings. By derivation of characteristic values from the sensor signal, different simulated defects can be detected reliably: seeded defects in the inner and outer race of rolling element bearings as well as the occurrence of mixed friction in the sliding surface bearing due to interrupted lubricant inflow.


Author(s):  
J. Saliba ◽  
A. Loukili ◽  
J.P. Regoin ◽  
D. Grégoire ◽  
L. Verdon ◽  
...  

The fracture process zone (FPZ) was investigated on unnotched and notched beams with different notch depths. Three point bending tests were realized on plain concrete under crack mouth opening displacement (CMOD) control. Crack growth was monitored by applying the acoustic emission (AE) technique. In order to improve our understanding of the FPZ, the width and length of the FPZ were followed based on the AE source locations maps and several AE parameters were studied during the entire loading process. The bvalue analysis, defined as the log-linear slope of the frequency-magnitude distribution of acoustic emissions, was also carried out to describe quantitatively the influence of the relative notch depth on the fracture process. The results show that the number of AE hits increased with the decrease of the relative notch depth and an important AE energy dissipation was observed at the crack initiation in unnotched beams. In addition, the relative notch depth influenced the AE characteristics, the process of crack propagation, and the brittleness of concrete.


2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Xizhen Sun ◽  
Fanbao Meng ◽  
Ce Zhang ◽  
Xucai Zhan ◽  
He Jiang

The geometric distribution of initial damages has a great influence on the strength and progressive failure characteristics of the fractured rock mass. Initial damages of the fractured rock were simplified as parallel cracks in different geometric distributions, and then, the progressive failure and acoustic emission (AE) characteristics of specimens under the uniaxial compression loading were analyzed. The red sandstone (brittle materials) specimens with the parallel preexisting cracks by water jet were used in the tests. The energy peak and stress attenuation induced by the energy release of crack initiation were intuitively observed in the test process. Besides, three modes of rock bridge coalescence were obtained, and wing crack was the main crack propagation mode. The wing crack and other cracks were initiated in different loading stages, which were closely related to the energy level of crack initiation. The propagation of wing crack (stable crack) consumed a large amount of energy, and then, the propagation of shear crack, secondary crack, and anti-wing crack (unstable crack) was inhibited. The relationship between the crack propagation mode and the geometric distribution of existing cracks in the specimen was revealed. Meanwhile, the strength characteristic and failure mode of fractured rock with the different geometric distributions of preexisting crack were also investigated. The energy evolution characteristics and crack propagation were also analyzed by numerical modeling (PFC2D).


Sign in / Sign up

Export Citation Format

Share Document