Is it Economical to Ignore the Driver? A Case Study on Multimode Combustion

2015 ◽  
Author(s):  
Sandro P. Nüesch ◽  
Anna G. Stefanopoulou
Keyword(s):  
Residence Time ◽  
Fuel Economy ◽  
Supervisory Control ◽  
Combustion Engine ◽  
Operating Conditions ◽  
Mode Switching ◽  
Mode Switch ◽  
Trade Off ◽  
Hcci Combustion ◽  
Torque Response

Ignoring the driver’s torque command can be beneficial for fuel economy, especially if it leads to extended residence time at efficient operating conditions. We answered this question for a particular engine, which allows mode switches between spark ignition (SI) and homogeneous charge compression ignition (HCCI) combustion. When operating such a multimode combustion engine it might be required to defer a load command outside the feasible regime of one combustion mode until a mode switch is accomplished. The resulting delays in engine torque response might negatively affect vehicle performance and drivability. In this paper a longitudinal vehicle model is presented, which incorporates dynamics associated with SI/HCCI mode switching. Two exemplary supervisory control strategies were evaluated in terms of fuel economy and torque behavior. It was seen that the duration of a mode switch may be short enough to avoid substantial impairment in torque response. This in turn would lead to the opportunity of purposefully ignoring the driver command. Thereby, the residence time in the beneficial HCCI combustion regime is prolonged and fuel-expensive mode switching avoided. The result is a trade-off between torque deviation and improvements in fuel economy. Finally, based on this trade-off the supervisory control strategy relying on a short-term prediction of engine load was seen to achieve similar fuel economy with slightly improved torque response than a strategy without prediction.

Methodology to Evaluate the Fuel Economy of a Multimode Combustion Engine With Three-Way Catalytic Converter

2014 ◽  
Author(s):  
Sandro P. Nüesch ◽  
Anna G. Stefanopoulou ◽  
Li Jiang ◽  
Jeffrey Sterniak
Keyword(s):  
Fuel Economy ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Oxygen Storage ◽  
Nox Emissions ◽  
Combustion Mode ◽  
Mode Switch ◽  
Drive Cycle ◽  
Finite State ◽  
The Impact

Highly diluted, low temperature homogeneous charge compression ignition (HCCI) combustion leads to ultra-low levels of engine-out NOx emissions. A standard drive cycle, however, would require switches between HCCI and spark-ignited (SI) combustion modes. In this paper a methodology is introduced, investigating the fuel economy of such a multimode combustion concept in combination with a three-way catalytic converter (TWC). The TWC needs to exhibit unoccupied oxygen storage sites in order to show acceptable performance. But the lean exhaust gas during HCCI operation fills the oxygen storage and leads to a drop in NOx conversion efficiency. Eventually the levels of NOx become unacceptable and a mode switch to a fuel rich combustion mode is necessary in order to deplete the oxygen storage. The resulting lean-rich cycling leads to a penalty in fuel economy. In order to evaluate the impact of those penalties on fuel economy, a finite state model for combustion mode switches is combined with a longitudinal vehicle model and a phenomenological TWC model, focused on oxygen storage. The aftertreatment model is calibrated using combustion mode switch experiments from lean HCCI to rich spark-assisted HCCI and back. Fuel and emissions maps acquired in steady state experiments are used. Two depletion strategies are compared in terms of their influence on drive cycle fuel economy and NOx emissions.

scholarly journals Fuel Economy of a Multimode Combustion Engine With Three-Way Catalytic Converter

2014 ◽  
Vol 137 (5) ◽  
Author(s):  
Sandro P. Nüesch ◽  
Anna G. Stefanopoulou ◽  
Li Jiang ◽  
Jeff Sterniak
Keyword(s):  
Fuel Economy ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Combustion Efficiency ◽  
Oxygen Storage ◽  
Nox Emissions ◽  
Combustion Mode ◽  
Mode Switch ◽  
Drive Cycle ◽  
The Impact

Highly diluted, low temperature homogeneous charge compression ignition (HCCI) combustion leads to ultralow levels of engine-out NOx emissions. A standard drive cycle, however, would require switches between HCCI and spark-ignited (SI) combustion modes. In this paper we quantify the efficiency benefits of such a multimode combustion engine, when emission constraints are to be met with a three-way catalytic converter (TWC). The TWC needs unoccupied oxygen storage sites in order to achieve acceptable performance. The lean exhaust gas during HCCI operation, however, fills the oxygen storage and leads to a drop in NOx conversion efficiency. If levels of tailpipe NOx become unacceptable, a mode switch to a fuel rich combustion mode is necessary in order to deplete the oxygen storage and restore TWC efficiency. The resulting lean-rich cycling leads to a penalty in fuel economy. Another form of penalty originates from the lower combustion efficiency during a combustion mode switch itself. In order to evaluate the impact on fuel economy of those penalties, a finite state model for combustion mode switches is combined with a longitudinal vehicle model and a phenomenological TWC model, focused on oxygen storage. The aftertreatment model is calibrated using combustion mode switch experiments from lean HCCI to rich spark-assisted HCCI (SA-HCCI) and back. Fuel and emission maps acquired in steady-state experiments are used. Different depletion strategies are compared in terms of their influence on drive cycle fuel economy and NOx emissions. It is shown that even an aggressive lean-rich cycling strategy will marginally satisfy the cumulated tailpipe NOx emission standards under warmed-up conditions. More notably, the cycling leads to substantial fuel penalties that negate most of HCCI's efficiency benefits.

Rankine Cycle for Hybrid Vehicles: The Potential for CO2 Emissions Reduction

2015 ◽  
Author(s):  
Ivica Kraljevic ◽  
Hans-Peter Kollmeier ◽  
Ulrich Spicher
Keyword(s):  
Fuel Economy ◽  
Hybrid Electric Vehicle ◽  
Waste Heat ◽  
Combustion Engine ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Operating Cycle ◽  
Vehicle Simulation ◽  
Exhaust Waste Heat

This paper presents the analysis of a Rankine cycle unit applied to improve overall efficiency of a hybrid electric vehicle (HEV). Exhaust waste heat is recovered from the internal combustion engine (ICE) and is converted into electrical power that is fed into the electrical system on board. The discontinuously available exhaust waste heat from the ICE operating cycle is stored as sensible heat in a pressurized working fluid applying the principle of a Ruths storage tank. Thus, it can provide almost constant mass flows to the expansion device during discharge in contrast to the standard Rankine cycle. It is also shown that the outlined system configuration leads to faster engine warm up resulting in optimum ICE operating conditions improving fuel economy. The benefits of a mild HEV versus conventional car powertrain are outlined step by step in a vehicle simulation. Additionally, improvement in fuel economy achieved by applying an additional Rankine cycle is demonstrated in the New European Driving Cycle (NEDC).

Nitrogen use efficiency: does a trade-off exist between the N productivity and the mean residence time within species?

2008 ◽  
Vol 56 (3) ◽  
pp. 272 ◽  
Author(s):  
Zhi Y. Yuan ◽  
Han Y. H. Chen ◽  
Ling H. Li
Keyword(s):  
Residence Time ◽  
Nitrogen Use Efficiency ◽  
Mean Residence Time ◽  
Negative Relationship ◽  
Controlled Experiments ◽  
Nitrogen Use ◽  
Trade Off ◽  
N Supply ◽  
Use Efficiency ◽  
The Mean

Nitrogen use efficiency (NUE) can be divided into two components, i.e. N productivity (A) and the mean residence time (MRT). Controlled experiments indicate that there is not a trade-off between A and MRT within species, but this theory has not been well tested in field conditions. Here, we studied the A, MRT and NUE of Stipa krylovii Roshev. in a grassland over 4 years of N fertilisation experimentation. The three parameters (A, MRT and NUE) were significantly related to soil N supply and there was a negative relationship between A and MRT within this species (r = –0.775, P < 0.05), i.e. plants with higher A had lower MRT. Our results showed a trade-off between A and MRT within this Stipa species and this observed trade-off was attributed to different responses of A and MRT to soil fertility.

scholarly journals Analysis of the Total Unit Energy Consumption of a Car with a Hybrid Drive System in Real Operating Conditions

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3966
Author(s):  
Jarosław Mamala ◽  
Michał Śmieja ◽  
Krzysztof Prażnowski
Keyword(s):  
Energy Consumption ◽  
Internal Combustion Engine ◽  
Electric Drive ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Hybrid Drive ◽  
Total Unit ◽  
Unit Energy ◽  
Unit Energy Consumption

The market demand for vehicles with reduced energy consumption, as well as increasingly stringent standards limiting CO2 emissions, are the focus of a large number of research works undertaken in the analysis of the energy consumption of cars in real operating conditions. Taking into account the growing share of hybrid drive units on the automotive market, the aim of the article is to analyse the total unit energy consumption of a car operating in real road conditions, equipped with an advanced hybrid drive system of the PHEV (plug-in hybrid electric vehicles) type. In this paper, special attention has been paid to the total unit energy consumption of a car resulting from the cooperation of the two independent power units, internal combustion and electric. The results obtained for the individual drive units were presented in the form of a new unit index of the car, which allows us to compare the consumption of energy obtained from fuel with the use of electricity supported from the car’s batteries, during journeys in real road conditions. The presented research results indicate a several-fold increase in the total unit energy consumption of a car powered by an internal combustion engine compared to an electric car. The values of the total unit energy consumption of the car in real road conditions for the internal combustion drive are within the range 1.25–2.95 (J/(kg · m)) in relation to the electric drive 0.27–1.1 (J/(kg · m)) in terms of instantaneous values. In terms of average values, the appropriate values for only the combustion engine are 1.54 (J/(kg · m)) and for the electric drive only are 0.45 (J/(kg · m)) which results in the internal combustion engine values being 3.4 times higher than the electric values. It is the combustion of fuel that causes the greatest increase in energy supplied from the drive unit to the car’s propulsion system in the TTW (tank to wheels) system. At the same time this component is responsible for energy losses and CO2 emissions to the environment. The results were analysed to identify the differences between the actual life cycle energy consumption of the hybrid powertrain and the WLTP (Worldwide Harmonized Light-Duty Test Procedure) homologation cycle.

A Solution Framework for Response Surface-Based Multiple Quality Characteristics Optimization

2018 ◽  
Vol 25 (05) ◽  
pp. 1850025
Author(s):  
Sasadhar Bera ◽  
Indrajit Mukherjee
Keyword(s):  
Response Surface ◽  
Optimization Problems ◽  
Real Life ◽  
Quality Characteristics ◽  
Operating Conditions ◽  
Simultaneous Optimization ◽  
Trade Off ◽  
Multiple Quality Characteristics ◽  
Pin On Disc ◽  
Application Potential

A common problem generally encountered during manufacturing process improvement involves simultaneous optimization of multiple ‘quality characteristics’ or so-called ‘responses’ and determining the best process operating conditions. Such a problem is also referred to as ‘multiple response optimization (MRO) problem’. The presence of interaction between the responses calls for trade-off solution. The term ‘trade-off’ is an explicit compromised solution considering the bias and variability of the responses around the specified targets. The global exact solution in such types of nonlinear optimization problems is usually unknown, and various trade-off solution approaches (based on process response surface (RS) models or without using process RS models) had been proposed by researchers over the years. Considering the prevalent and preferred solution approaches, the scope of this paper is limited to RS-based solution approaches and similar closely related solution framework for MRO problems. This paper contributes by providing a detailed step-by-step RS-based MRO solution framework. The applicability and steps of the solution framework are also illustrated using a real life in-house pin-on-disc design of experiment study. A critical review on solution approaches with details on inherent characteristic features, assumptions, limitations, application potential in manufacturing and selection norms (indicative of the application potential) of suggested techniques/methods to be adopted for implementation of framework is also provided. To instigate research in this field, scopes for future work are also highlighted at the end.

Characterization of a Piezoelectric Membrane for MEMS Power

2001 ◽  
Author(s):  
K. Bruce ◽  
R. Richards ◽  
D. Bahr ◽  
C. Richards
Keyword(s):  
Thin Film ◽  
Power System ◽  
Combustion Engine ◽  
Thermal Power ◽  
Operating Conditions ◽  
Mechanical Power ◽  
Central Component ◽  
Carnot Cycle ◽  
Modular Architecture ◽  
Micro Power

Abstract Work toward the development of a thin-film piezoelectric membrane generator is presented. The membrane generator is the central component of a new MEMS power generation system, the P3 micro power system. The P3 micro power system is based on a two-dimensional, modular architecture, in which the individual generic modules or unit cells each have all the functions of an engine integrated. Each unit cell is an external combustion engine, in which thermal power is converted to mechanical power through the use of a novel thermodynamic cycle that approaches the ideal vapor Carnot cycle. Mechanical power is converted into electrical power through the use of a thin-film piezoelectric membrane generator. This paper introduces the concept of the thin-film piezoelectric membrane generator, and describes its design and fabrication. Results of a study to characterize the performance of the piezoelectric membrane generator under expected operating conditions are presented. Current prototypes of the membrane generator are shown to be capable of producing a peak power of 0.1 milliWatts at a voltage of 0.5 Volts.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

Use of an Integrated Approach for Analysis and Design of Turbocharged Internal Combustion Engine

2021 ◽  
Author(s):  
Thiago Ebel ◽  
Mark Anderson ◽  
Parth Pandya ◽  
Mat Perchanok ◽  
Nick Tiney ◽  
...  
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Early Stage ◽  
Pressure Ratio ◽  
Integrated Approach ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Dynamics Simulation ◽  
Analysis And Design ◽  
Performance Requirements

Abstract When developing a turbocharged internal combustion engine, the choice of turbocharger is usually based on designer experience and existing hardware. However, proper turbocharger design relies on matching the compressor and turbine performance to the engine requirements so that parameters such as boost and back pressure, compressor pressure ratio, and turbine inlet temperatures meet the needs of the engine without exceeding its allowable operating envelope. Therefore, the ultimate measure of a successful turbocharger design is how well it is matched to an engine across various operating conditions. This, in turn, determines whether a new turbocharger is required, or an existing solution can be used. When existing turbocharger solutions are not viable, the engine designer is at a loss on how to define a new turbocharger that meets the desired performance requirements. A common approach in industry has been to scale the performance of an existing turbocharger (compressor and turbine maps) and take these requirements for Original Equipment Manufacturers to possibly match it with a real machine. However, the assumptions made in a basic scaling process are quite simplistic and generally not satisfactory in this situation. A better approach would be to use a validated meanline model for a compressor and turbine instead, allowing to perform an actual preliminary design of such components. Such approach allows to link the engine performance requirements in a very early stage of te component design project and it guides the designer for the design decisions, such as rotor size, variable geometry nozzles, diameter, or shroud trims and others. Therefore, a feasible solution is more likely with design less iterations. This paper describes a methodology for an integrated approach to design and analyze a turbocharged internal combustion engine using commercially available state-of-the-art 1D gas dynamics simulation tool linked to two powerful turbomachinery meanline programs. The outputs of this analysis are detailed performance data of the engine and turbocharger at different engine operating conditions. Two case studies are then presented for a 10-liter diesel truck engine. The first study demonstrates how the programs are used to evaluate an existing engine and reverse engineer an existing turbocharger based only on the available performance maps. Then a second study is done using a similar approach but redesigning a new turbocharger (based on the reverse engineered one) for an increased torque output of the same engine.

Sign in / Sign up

Export Citation Format

Share Document