Tribological Behavior of High Density Polyethylene Nanocomposites With Silane Treated Carbon Nanofibers

2011 ◽  
Author(s):  
Songbo Xu ◽  
Aydar Akchurin ◽  
X. W. Tangpong ◽  
Iskander S. Akhatov ◽  
Tian Liu ◽  
...  
Keyword(s):  
Carbon Nanofibers ◽  
Tribological Properties ◽  
High Density Polyethylene ◽  
High Density ◽  
Micro Hardness ◽  
Melt Mixing ◽  
Silane Coating ◽  
Pin On Disc ◽  
Treated Carbon ◽  
New Applications

New applications of carbon-based materials have been continuously developed in recent years. Carbon Nanofibers (CNFs) with silane coatings were added into high density polyethylene (HDPE) to improve the tribological properties of the nanocomposite material for biomedical applications. The nanocomposites were fabricated with various weight percentages of carbon nanofibers (0.5%, 1%, 3%) that were treated with different silane coating thicknesses (2.8nm, 46nm) through melt-mixing and compressive processing. The wear and friction tests were performed on a pin-on-disc tribometer under phosphate buffered saline lubricated condition. Compared with the pure HDPE, the friction coefficients of the nanocomposites were reduced dramatically and their wear resistance properties were also improved. Micro-hardness measurements of the nanocomposites were carried out and CNFs were found to be capable of improving the material’s micro-hardness effectively. The effects of concentration and silane coating thickness of CNFs on the tribological properties of the resulting nanocomposites were analyzed and the wear mechanism of the CNF/HDPE nanocomposites was discussed.

Wear and Friction of Carbon Nanofiber-Reinforced HDPE Composites

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Songbo Xu ◽  
Aydar Akchurin ◽  
Tian Liu ◽  
Weston Wood ◽  
X. W. Tangpong ◽  
...  
Keyword(s):  
Carbon Nanofibers ◽  
Tribological Properties ◽  
Carbon Nanofiber ◽  
Micro Hardness ◽  
Melt Mixing ◽  
Wear Rates ◽  
Silane Coating ◽  
Wear And Friction ◽  
Pin On Disc ◽  
New Applications

New applications of carbon-based materials have been continuously developed in recent years. Carbon nanofibers (CNFs) with silane coatings were added into high density polyethylene (HDPE) to improve the tribological properties of the nanocomposite material. The nanocomposites were fabricated with various weight percentages of carbon nanofibers (0.5 wt.%, 1 wt.% and 3 wt.%) that were treated with different silane coating thicknesses (2.8 nm and 46 nm) through melt-mixing and compressive processing. The wear and friction tests were performed on a pin-on-disc tribometer under phosphate buffered saline lubricated condition. Compared with the neat HDPE, the friction coefficients of the nanocomposites were reduced in all samples, yet only a couple of nanocomposite samples showed lower wear rates. Micro-hardness measurements of the nanocomposites were carried out and CNFs were found to be capable of increasing the material’s micro-hardness. The effects of concentration and silane coating thickness of CNFs on the tribological properties of the resulting nanocomposites were analyzed and the wear mechanisms of the HDPE/CNF nanocomposites were discussed.

Comparison of Tribological Performances of High Density Polyethylene Enhanced With Carbon Nanofibers

2012 ◽  
Author(s):  
Songbo Xu ◽  
Aydar Akchurin ◽  
X. W. Tangpong ◽  
Tian Liu ◽  
Weston Wood ◽  
...  
Keyword(s):  
Wear Resistance ◽  
High Density Polyethylene ◽  
Carbon Nanofiber ◽  
Optical Microscope ◽  
High Density ◽  
High Wear Resistance ◽  
Melt Mixing ◽  
Wear Rates ◽  
Silane Coating ◽  
Bearing Materials

High density polyethylene (HDPE) is widely used as bearing material in industrial application because of its low friction and high wear resistance properties. Carbon nanofiber (CNF) reinforced HDPE nanocomposites are promising materials for biomedical applications as well, such as being the bearing materials in total joint replacements. The main objective of the present study is to investigate how the wear of HDPE can be altered by the addition of either pristine or silane treated CNFs at different loading levels (0.5 wt.% and 3 wt.%). Two types of silane coating thicknesses, 2.8 nm and 46 nm, were applied on the surfaces of oxidized CNFs to improve the interfacial bonding strength between the CNFs and the matrix. The CNF/HDPE nanocomposites were prepared through melt mixing and hot-pressing. The coefficients of friction (COFs) and wear rates of the neat HDPE and CNF/HDPE nanocomposites were determined using a pin-on-disc tribometer under dry sliding conditions. The microstructures of the worn surfaces of the nanocomposites were characterized using both scanning electron microscope (SEM) and optical microscope to analyze their wear mechanisms. Compared with the neat HDPE, the COF of the nanocomposites were reduced. The nanocomposite reinforced with CNFs coated with the thicker silane coating (46 nm) at 0.5 wt.% loading level was found to yield the highest wear resistance with a wear rate reduction of nearly 68% compared to the neat HDPE.

Tribological properties of High Density Polyethylene based composite: The effect of mollusc shell particles under dry condition

2020 ◽  
pp. 002199832096565
Author(s):  
Besma Sidia ◽  
Walid Bensalah
Keyword(s):  
Tribological Properties ◽  
High Density Polyethylene ◽  
Tribological Behavior ◽  
High Density ◽  
Ftir Analysis ◽  
Mollusc Shell ◽  
Sem Images ◽  
Pin On Disc ◽  
Shell Particles ◽  
Wear Tests

This article highlights the importance of the addition of Mollusc shell (MS) particles, as bio-filler, on the tribological behavior of high-density polyethylene (HDPE) matrix. The elaborated biocomposites are intended to be used as an orthopedic replacement biomaterial. Different mass content of MS (0, 5, 10, 15 and 20 wt. %) have been added to the HDPE matrix. FTIR analysis, crystallinity rate and Rockwell hardness of different bio-composites were performed. A reciprocating pin-on-disc tribometer was used to fulfil dry wear tests. FTIR analysis showed that the presence of MS particles improved the crystallinity of the HDPE phase. Adding to that, it was found that MS improved the hardness, friction coefficient and wear resistance of the HDPE polymer. In fact, by adding 5 wt. % of MS to the HDPE, good tribological properties were achieved. Scanning Electron Microscopy (SEM) was performed to investigate the wear morphology of biocomposites under dry condition. SEM images showed that the morphology of the worn surfaces had been improved by the addition of MS to the polymer. Finally, a wear scenario was proposed.

Effect of inorganic nanofillers on the impact behavior and fracture probability of industrial high-density polyethylene nanocomposite

2017 ◽  
Vol 52 (18) ◽  
pp. 2431-2442 ◽  
Author(s):  
Harun Sepet ◽  
Necmettin Tarakcioglu ◽  
RDK Misra
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Density Polyethylene ◽  
Fracture Probability ◽  
High Density ◽  
Impact Behavior ◽  
Inorganic Filler ◽  
Melt Mixing ◽  
The Impact ◽  
Scanning Electron

The main purpose of this work is to study how the morphology of nanofillers and dispersion and distribution level of inorganic nanofiller influence the impact behavior and fracture probability of inorganic filler filled industrial high-density polyethylene nanocomposites. For this study, nanoclay and nano-CaCO3 fillers–high-density polyethylene mixings (0, 1, 3, 5 wt.% high-density polyethylene) was prepared by melt-mixing method using a compounder system. The impact behavior was examined by charpy impact test, scanning electron microscopy, and probability theory and statistics. The level of the dispersion was characterized with scanning electron microscopy energy dispersive X-ray spectroscopy analysis. The results showed rather good dispersion of both of inorganic nanofiller, with a mixture of exfoliated and confined morphology. The results indicated that the impact strength of the industrial nanocomposite decreased with the increase of inorganic particulate content. The impact reliability of the industrial nanocomposites depends on the type of nanofillers and their dispersion and distribution in the matrix.

scholarly journals In-Situ Synthesis and Property Evaluation of High-Density Polyethylene Reinforced Groundnut Shell Particulate Composite

2021 ◽  
Vol 6 (4) ◽  
pp. 305-311
Author(s):  
Abdulmumin Adebisi ◽  
Tajudeen Mojisola ◽  
Umar Shehu ◽  
Muhammed Sani Adam ◽  
Yusuf Abdulaziz
Keyword(s):  
Tensile Strength ◽  
Water Absorption ◽  
Impact Energy ◽  
High Density Polyethylene ◽  
In Situ Synthesis ◽  
High Density ◽  
Compression Moulding ◽  
Melt Mixing ◽  
Groundnut Shell

In-situ synthesis of high-density polyethylene (HDPE) reinforced groundnut shell particulate (GSP) composite with treated GSP within the range of 10-30 wt% at 10 wt% has been achieved. The adopted technique used in the production of the composite is melt mixing and compounding using two roll mills with a compression moulding machine. Properties such as hardness, tensile strength, impact energy and water absorption analysis were examined. The result revealed that addition of GSP increases the hardness value from 22.3 to 87 Hv. However, the tensile strength progressively decreased as the GSP increases in the HDPE. This trend arises due to the interaction between neighbouring reinforced particulate which appears to influence the matrix flow, thereby inducing embrittlement of the polymer matrix. It was also observed that water absorption rate steadily increased with an increase in the exposure time and the absorbed amount of water increases by increasing the wt% of the GSP. Analysing the obtained results, it was concluded that there were improvements in the hardness, tensile strength, impact energy and water absorption properties of the HDPE-GSP polymer composite when compared to unreinforced HDPE. On these premises, GSP was found as a promising reinforcement which can positively influence the HDPE properties of modern composites.

Effect of particulate fillers on natural rubber/high-density polyethylene blends for roofing application

2020 ◽  
pp. 096739112093461
Author(s):  
WVWH Wickramaarachchi ◽  
S Walpalage ◽  
SM Egodage
Keyword(s):  
Impact Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
Thermoplastic Elastomer ◽  
Cost Effective ◽  
Barium Sulphate ◽  
Filler Loading ◽  
High Density ◽  
Melt Mixing ◽  
Excellent Property

Blending of two or more polymers generates a new material, which is more cost-effective than a newly synthesised material. Blending-type thermoplastic elastomer (TPE) is produced by melt-mixing of a thermoplastic with a rubber. These blends have high demands associated with excellent property combinations of the parent materials. Particulate fillers are used in the rubber and plastic industry for property modification and cost reduction. In this work, six particulate fillers, namely, calcium carbonate, barium sulphate (BaSO4), kaolin, talc, Snobrite clay and dolomite were used to develop natural rubber (NR)/high-density polyethylene (HDPE) TPE blends, and the most suitable filler for roofing application was identified. A series of NR/HDPE 20/80 blends were prepared by varying filler loading from 10 phr to 30 phr at 10 phr intervals using a Plasticorder. Mechanical properties, such as tensile strength, hardness, impact strength and tear strength, and gel content of the blends were investigated. The addition of talc, dolomite and kaolin to NR/HDPE blend showed reduced impact strength, which is the most important property for a roofing application. The other three fillers showed improved impact strength at specific loadings. The blend with 30 phr of BaSO4 was identified as the best blend, as per the overall performance.

scholarly journals Enhancement of the processing window and performance of polyamide 1010/bio‐based high‐density polyethylene blends by melt mixing with natural additives

2019 ◽  
Vol 69 (1) ◽  
pp. 61-71 ◽  
Author(s):  
Luis Quiles‐Carrillo ◽  
Nestor Montanes ◽  
Vicent Fombuena ◽  
Rafael Balart ◽  
Sergio Torres‐Giner
Keyword(s):  
High Density Polyethylene ◽  
High Density ◽  
Melt Mixing ◽  
Polyethylene Blends ◽  
Processing Window ◽  
And Performance ◽  
Polyamide 1010 ◽  
Natural Additives

scholarly journals Graphene Nanoplatelet-Reinforced Poly(vinylidene fluoride)/High Density Polyethylene Blend-Based Nanocomposites with Enhanced Thermal and Electrical Properties

Nanomaterials ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 361 ◽  
Author(s):  
Kartik Behera ◽  
Mithilesh Yadav ◽  
Fang-Chyou Chiu ◽  
Kyong Rhee
Keyword(s):  
Isothermal Crystallization ◽  
High Density Polyethylene ◽  
Vinylidene Fluoride ◽  
High Density ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Graphene Nanoplatelet ◽  
Polyethylene Blend ◽  
Poly Vinylidene Fluoride ◽  
Mixing Method

In this study, a graphene nanoplatelet (GNP) was used as a reinforcing filler to prepare poly(vinylidene fluoride) (PVDF)/high density polyethylene (HDPE) blend-based nanocomposites through a melt mixing method. Scanning electron microscopy confirmed that the GNP was mainly distributed within the PVDF matrix phase. X-ray diffraction analysis showed that PVDF and HDPE retained their crystal structure in the blend and composites. Thermogravimetric analysis showed that the addition of GNP enhanced the thermal stability of the blend, which was more evident in a nitrogen environment than in an air environment. Differential scanning calorimetry results showed that GNP facilitated the nucleation of PVDF and HDPE in the composites upon crystallization. The activation energy for non-isothermal crystallization of PVDF increased with increasing GNP loading in the composites. The Avrami n values ranged from 1.9–3.8 for isothermal crystallization of PVDF in different samples. The Young’s and flexural moduli of the blend improved by more than 20% at 2 phr GNP loading in the composites. The measured rheological properties confirmed the formation of a pseudo-network structure of GNP-PVDF in the composites. The electrical resistivity of the blend reduced by three orders at a 3-phr GNP loading. The PVDF/HDPE blend and composites showed interesting application prospects for electromechanical devices and capacitors.

Palm Kernel Shell Filled Recycled High-Density Polyethylene: Effect of Filler Loading

2016 ◽  
Vol 857 ◽  
pp. 191-195 ◽  
Author(s):  
A. Nadiatul Husna ◽  
Bee Ying Lim ◽  
H. Salmah ◽  
Chun Hong Voon
Keyword(s):  
Thermal Stability ◽  
High Density Polyethylene ◽  
Thermo Gravimetric Analysis ◽  
Palm Kernel ◽  
Filler Loading ◽  
High Density ◽  
Gravimetric Analysis ◽  
Melt Mixing ◽  
Palm Kernel Shell ◽  
Thermal Stability Of

Palm kernel shells (PKS) filled recycled high density polyethylene (rHDPE) biocomposites were produced using melt mixing. The biocomposites were prepared on Brabender Plasticorder at temperature of 185 °C and rotor speed of 50 rpm by varying filler loading (0 to 40 phr). In this study, the effect of PKS loading on rheological properties and thermal stability of rHDPE/PKS were investigated. Rheological study of the biocomposites was carried out by means of capillary rheometer under temperature of 190 °C, 200 °C and 210 °C. Thermal properties of biocomposites were studied by using thermo gravimetric analysis (TGA). The rheological results showed that the flowability of the composite increased with increasing temperature. Meanwhile, the result of TGA showed that at higher PKS loading, rHDPE/PKS biocomposites had lower total weight loss. The thermal stability of the biocomposites was reduced due to the addition of filler loading.

Effects of Epoxidized Nature Rubber on High Density Polyethylene/Recycled Acrylonitrile Butadiene Rubber/Banana Skin Powder Composites

2015 ◽  
Vol 754-755 ◽  
pp. 201-204
Author(s):  
Ragunathan Santiagoo ◽  
Sam Sung Ting ◽  
Azlinda Abdul Ghani ◽  
Hanafi Ismail ◽  
Awiezan Mislan
Keyword(s):  
Tensile Strength ◽  
High Density Polyethylene ◽  
High Density ◽  
Butadiene Rubber ◽  
Rotor Speed ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Acrylonitrile Butadiene Rubber ◽  
Twin Screw ◽  
Powder Composites

The compatibilizer effect of ENR-50 on the tensile properties of high density polyethylene (HDPE)/recycled acrylonitrile butadiene rubber (NBRr)/banana skin powder (BSP)/ composites has been studies. HDPE/NBRr/BSP composites were prepared by melt mixing technique using twin-screw at 180 °C for 9 minutes at rotor speed 50 rpm. The six different composites studied were 100/0/5, 80/20/5, 70/30/5, 60/40/5, 50/50/5, and 40/60/5. As for compatibilized composite a fix 5 wt% of ENR-50 was evaluated. The specimens were analysed for tensile strength and elongation at break (Eb). The results showed that tensile strength and the elongation at break were decreases with the increasing of NBRr loading. However for ENR-50 compatibilized composites, higher tensile strength and elongation at break was recorded. The ENR-50 was found to be an excellent compatibilizer for HDPE/NBRr/BSP composites.

Sign in / Sign up

Export Citation Format

Share Document